期刊文献+
共找到4篇文章
< 1 >
每页显示 20 50 100
双相钢激光焊管的焊缝组织演变及扩口性能研究 被引量:2
1
作者 陈礼斌 夏明生 徐杰 《河北冶金》 2012年第9期11-15,共5页
介绍了马氏体含量不同的双相钢(DP590和DP780)激光焊管的焊缝组织演变,研究了焊缝硬度分布特征及其对扩口性能的影响。结果表明:激光焊缝的熔合区存在明显硬化,组织为单一的马氏体,DP780钢热影响区出现了显著的软化,DP590钢无软化区存在... 介绍了马氏体含量不同的双相钢(DP590和DP780)激光焊管的焊缝组织演变,研究了焊缝硬度分布特征及其对扩口性能的影响。结果表明:激光焊缝的熔合区存在明显硬化,组织为单一的马氏体,DP780钢热影响区出现了显著的软化,DP590钢无软化区存在,造成这一差别的原因在于两者马氏体含量不同;软化区的存在导致DP780钢激光焊管的扩口率急剧下降,仅为DP590钢的10%左右;建立了焊管扩口的数值模型,模拟结果与试验结果相吻合。 展开更多
关键词 双相钢 激光焊管 焊缝组织 扩口性能 研究
下载PDF
加工工艺对高精度铂毛细管扩口性能的影响
2
作者 马光 李银娥 《有色金属》 CSCD 2002年第B07期49-52,共4页
研究不同加工工艺对高精度铂毛细管扩口性能的影响。试验结果表明,采用通用的轧管-带芯杆拉拔-多次空拉工艺时,铂毛细管扩口破裂率较高;采用板材拉伸-带芯杆拉拔-少量空拉工艺时,铂毛细管扩口时无破裂。
关键词 加工工艺 铂毛细管 扩口性能 自动控制设备
下载PDF
5052铝合金无缝薄壁管扩口性能研究
3
作者 高宝亭 杨晓禹 +1 位作者 刚建伟 张岩 《铝加工》 CAS 2019年第1期28-31,共4页
通过对比进口料和国产料的组织,确定了提高5052合金管材扩口性能组织的改进方向为细化组织晶粒度,消除组织各向异性。对比拉伸法和轧制法,发现轧制法生产的管材退火后组织晶粒更细小且各向异性更小。通过退火制度摸索,确定采用(470℃~... 通过对比进口料和国产料的组织,确定了提高5052合金管材扩口性能组织的改进方向为细化组织晶粒度,消除组织各向异性。对比拉伸法和轧制法,发现轧制法生产的管材退火后组织晶粒更细小且各向异性更小。通过退火制度摸索,确定采用(470℃~490℃)×4h制度退火后的轧制管材组织的均匀程度最好,扩口成功率最高,完全可以达到实际应用需求。 展开更多
关键词 5052合金 薄壁管 扩口性能 加工工艺 退火工艺
下载PDF
Influence of volute distortion on the performance of turbocharger centrifugal compressor with vane diffuser 被引量:5
4
作者 ZHENG XinQian JIN Lei TAMAKI Hideaki 《Science China(Technological Sciences)》 SCIE EI CAS 2013年第11期2778-2786,共9页
As the geometry of the volute of turbocharger compressor is non-axisymmetric,it causes a distortion at the outlet of the diffuser and influences the upstream components.A distortion model in which a pressure distortio... As the geometry of the volute of turbocharger compressor is non-axisymmetric,it causes a distortion at the outlet of the diffuser and influences the upstream components.A distortion model in which a pressure distortion was applied as outlet boundary condition was established to simulate the distortion induced by the volute.It turned out to be sufficient to impose a circumferentially asymmetric pressure distribution at the outlet of the diffuser to replace the volute.Based on the distortion model which was verified,the influence of the amplitude of the distortion on the performance of centrifugal compressor was studied in detail.The results show that the distortion severely harms aerodynamic stability of the investigated compressor.The larger the amplitude of the distortion,the worse the performance of the compressor.The distortion induced by asymmetric volute propagates to upstream components and causes local flow separation at part of diffuser and impeller,and then causes the compressor surge.When the amplitude of the volute distortion is 10%,the stable flow range of the centrifugal compressor decreases to near zero.To authors’knowledge,the relationship between the compressor performance and distortion amplitude is first obtained quantitatively,which provides evidence to improve the performance of turbocharger compressor by decreasing the distortion induced by asymmetric volute. 展开更多
关键词 TURBOCHARGER vane diffuser centrifugal compressor stability DISTORTION
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部