A continuous semisolid extending extrusion （CSEP） method was proposed. Temperature field and metal flow during continuous semisolid extending extrusion process of 6201 alloy tube were studied. During the process, th...A continuous semisolid extending extrusion （CSEP） method was proposed. Temperature field and metal flow during continuous semisolid extending extrusion process of 6201 alloy tube were studied. During the process, the temperature in the roll-shoe cavity decreases gradually, and the isothermal lines of the alloy deviate from the shoe side to the work roll side in the roll–shoe gap. Metal flow velocity decreases gradually from the surface of the work roll to the surface of the shoe. In the extrusion mould, alloy temperature decreases gradually from the entrance to the exit and from the center to the sidewall of the mould. The extending cavity is radially filled with the alloy. The flow lines in the tube corresponding to the centers of the splitflow orifices and the welding gaps are dense, and the corresponding harness values are high; there are 8 transitional bands between them. In order to prepare 6201 alloy tubes with good surface quality, the pouring temperature from 750 ℃ to 780 ℃ was suggested.展开更多
A silicon temperature sensor with a conventional resistor structure is fabricated on thin-film silicon-on-insulator (SOI) substrate.The sensor has very promising characteristics.The maximum operating temperature ca...A silicon temperature sensor with a conventional resistor structure is fabricated on thin-film silicon-on-insulator (SOI) substrate.The sensor has very promising characteristics.The maximum operating temperature can reach 550℃ even at a low current of 0.1mA.Experimental results support that the minority-carrier exclusion effect can be strong in the conventional resistor structure when the silicon film is sufficiently thin,thus significantly raising the maximum operating temperature.Moreover,since the structure of the device on thin-film SOI wafer is not crucial in controlling the maximum operating temperature,device layout can be varied according to the requirements of applications.展开更多
A new humidity calibration facility using a 2-T （two-temperature）, constant pressure principle for generating gas of known humidity has been developed at NIS for primary realization of relative humidity scale in the...A new humidity calibration facility using a 2-T （two-temperature）, constant pressure principle for generating gas of known humidity has been developed at NIS for primary realization of relative humidity scale in the range from 13% to 98% for calibrating and testing hygrometers to improve the uncertainty. This paper reports the construction of the 2-T humidity generator describing its saturator and the test chamber system. Results of the efficiency tests of its saturator showed satisfactory generation performance for a primary realization of relative humidity scale. The expanded uncertainty of the relative humidity with a coverage factor k = 2 was found to be from ± 0.25 % to ± 0.67%.展开更多
Many engineering components, such as power-plant steam pipes, aero-engine turbine discs, etc., operate under severe loading/temperature conditions. As a result, cracks can initiate and subsequently propagate over time...Many engineering components, such as power-plant steam pipes, aero-engine turbine discs, etc., operate under severe loading/temperature conditions. As a result, cracks can initiate and subsequently propagate over time due to creep. The Liu and Murakami＇s model has proven to be a useful tool for the prediction of creep crack growth under such conditions. Previously, experimental conditions used in obtaining the constant ofmultiaxiality, a, have not reflected the multiaxial severity of the stress state ahead of a crack tip. Therefore, the present study presents a novel method for interpolating crack growth data to obtain a.展开更多
The fatigue and fracture behavior of nickel-based superalloy Inconel 718 was investigated up to the very high cycle regime under rotary bending tests at room temperature. It was found that this superalloy can still fr...The fatigue and fracture behavior of nickel-based superalloy Inconel 718 was investigated up to the very high cycle regime under rotary bending tests at room temperature. It was found that this superalloy can still fracture after exceeding 107 cycles. Fractographic analysis revealed that there was a transition from fatigue crack initiation at multi-sites to single initiation with decreasing stress levels. The fracture surface can be divided into four areas according to the appearance, associated with fracture mechanics analysis of the corresponding stress intensity factors. The fracture mechanism dominant in each area was disclosed by scanning electron microscope examination and analyzed in comparison with those obtained from the crack growth tests. Subsequently, life prediction modeling was proposed by estimating the crack initiation and propagation stage respectively. It was found that Chan (2003)'s model for initiation life and the Paris law for growth life can provide comparable predictions against the experimental life.展开更多
The local environment of Cu atoms in Fe73.5Cu1Nb3Si13.5B9 alloy was investigated by extended X-ray absorption fine structure(EXAFS).Cu clusters began to order when the annealing temperature was around 733 K from the r...The local environment of Cu atoms in Fe73.5Cu1Nb3Si13.5B9 alloy was investigated by extended X-ray absorption fine structure(EXAFS).Cu clusters began to order when the annealing temperature was around 733 K from the results of the Fourier transform curves.The fitting results showed that the first shell of the near fcc(face-centered cubic)Cu clusters only contained Cu atoms.The coordination number increased with the annealing temperature.Subsequently,the occupancy rate increased from 33.3%(annealed at 733 K)to 100% (annealed at 853 K).This local structural change of Cu atoms could probably affect the distribution of the bcc(body-centered cubic)α-Fe in Fe73.5Cu1Nb3Si13.5B9 alloy.展开更多
In this paper,the authors consider a family of smooth immersions Ft : Mn→Nn+1of closed hypersurfaces in Riemannian manifold Nn+1with bounded geometry,moving by the Hkmean curvature flow.The authors show that if the s...In this paper,the authors consider a family of smooth immersions Ft : Mn→Nn+1of closed hypersurfaces in Riemannian manifold Nn+1with bounded geometry,moving by the Hkmean curvature flow.The authors show that if the second fundamental form stays bounded from below,then the Hkmean curvature flow solution with finite total mean curvature on a finite time interval [0,Tmax)can be extended over Tmax.This result generalizes the extension theorems in the paper of Li(see "On an extension of the Hkmean curvature flow,Sci.China Math.,55,2012,99–118").展开更多
基金Projects (51034002, 50974038) supported by the National Natural Science Foundation of ChinaProject (132002) supported by the Fok Ying Tong Education FoundationProject (2011CB610405) supported by National Basic Research Program of China
文摘A continuous semisolid extending extrusion （CSEP） method was proposed. Temperature field and metal flow during continuous semisolid extending extrusion process of 6201 alloy tube were studied. During the process, the temperature in the roll-shoe cavity decreases gradually, and the isothermal lines of the alloy deviate from the shoe side to the work roll side in the roll–shoe gap. Metal flow velocity decreases gradually from the surface of the work roll to the surface of the shoe. In the extrusion mould, alloy temperature decreases gradually from the entrance to the exit and from the center to the sidewall of the mould. The extending cavity is radially filled with the alloy. The flow lines in the tube corresponding to the centers of the splitflow orifices and the welding gaps are dense, and the corresponding harness values are high; there are 8 transitional bands between them. In order to prepare 6201 alloy tubes with good surface quality, the pouring temperature from 750 ℃ to 780 ℃ was suggested.
文摘A silicon temperature sensor with a conventional resistor structure is fabricated on thin-film silicon-on-insulator (SOI) substrate.The sensor has very promising characteristics.The maximum operating temperature can reach 550℃ even at a low current of 0.1mA.Experimental results support that the minority-carrier exclusion effect can be strong in the conventional resistor structure when the silicon film is sufficiently thin,thus significantly raising the maximum operating temperature.Moreover,since the structure of the device on thin-film SOI wafer is not crucial in controlling the maximum operating temperature,device layout can be varied according to the requirements of applications.
文摘A new humidity calibration facility using a 2-T （two-temperature）, constant pressure principle for generating gas of known humidity has been developed at NIS for primary realization of relative humidity scale in the range from 13% to 98% for calibrating and testing hygrometers to improve the uncertainty. This paper reports the construction of the 2-T humidity generator describing its saturator and the test chamber system. Results of the efficiency tests of its saturator showed satisfactory generation performance for a primary realization of relative humidity scale. The expanded uncertainty of the relative humidity with a coverage factor k = 2 was found to be from ± 0.25 % to ± 0.67%.
文摘Many engineering components, such as power-plant steam pipes, aero-engine turbine discs, etc., operate under severe loading/temperature conditions. As a result, cracks can initiate and subsequently propagate over time due to creep. The Liu and Murakami＇s model has proven to be a useful tool for the prediction of creep crack growth under such conditions. Previously, experimental conditions used in obtaining the constant ofmultiaxiality, a, have not reflected the multiaxial severity of the stress state ahead of a crack tip. Therefore, the present study presents a novel method for interpolating crack growth data to obtain a.
基金Project supported by the National Natural Science Foundation of China (Nos 10872105 and 51071094)the Mitsubishi Heavy Industries, Ltd, Japan
文摘The fatigue and fracture behavior of nickel-based superalloy Inconel 718 was investigated up to the very high cycle regime under rotary bending tests at room temperature. It was found that this superalloy can still fracture after exceeding 107 cycles. Fractographic analysis revealed that there was a transition from fatigue crack initiation at multi-sites to single initiation with decreasing stress levels. The fracture surface can be divided into four areas according to the appearance, associated with fracture mechanics analysis of the corresponding stress intensity factors. The fracture mechanism dominant in each area was disclosed by scanning electron microscope examination and analyzed in comparison with those obtained from the crack growth tests. Subsequently, life prediction modeling was proposed by estimating the crack initiation and propagation stage respectively. It was found that Chan (2003)'s model for initiation life and the Paris law for growth life can provide comparable predictions against the experimental life.
基金supported by the National Natural Science Foundation of China(Grant No.51071109)the Young Excellent Talents in Tongji University(Grant No.2009KJ003)
文摘The local environment of Cu atoms in Fe73.5Cu1Nb3Si13.5B9 alloy was investigated by extended X-ray absorption fine structure(EXAFS).Cu clusters began to order when the annealing temperature was around 733 K from the results of the Fourier transform curves.The fitting results showed that the first shell of the near fcc(face-centered cubic)Cu clusters only contained Cu atoms.The coordination number increased with the annealing temperature.Subsequently,the occupancy rate increased from 33.3%(annealed at 733 K)to 100% (annealed at 853 K).This local structural change of Cu atoms could probably affect the distribution of the bcc(body-centered cubic)α-Fe in Fe73.5Cu1Nb3Si13.5B9 alloy.
基金supported by the National Natural Science Foundation of China(Nos.11301399,11126189,11171259,11126190)the Specialized Research Fund for the Doctoral Program of Higher Education(No.20120141120058)+1 种基金the China Postdoctoral Science Foundation(No.20110491212)the Fundamental Research Funds for the Central Universities(Nos.2042011111054,20420101101025)
文摘In this paper,the authors consider a family of smooth immersions Ft : Mn→Nn+1of closed hypersurfaces in Riemannian manifold Nn+1with bounded geometry,moving by the Hkmean curvature flow.The authors show that if the second fundamental form stays bounded from below,then the Hkmean curvature flow solution with finite total mean curvature on a finite time interval [0,Tmax)can be extended over Tmax.This result generalizes the extension theorems in the paper of Li(see "On an extension of the Hkmean curvature flow,Sci.China Math.,55,2012,99–118").
