关于北斗G2卫星的溯往追终

2022年1月,失效的北斗G2卫星被实践21号卫星从地球静止轨道拖入了坟墓轨道.为了这项捕获任务的安全实施,需要预先确定北斗G2的旋转状态.基于过去10 yr的测光观测数据展示了北斗G2卫星自转的演化过程.根据北斗G2的自转速度和轨道的演化,确认了在过去的10 yr里发生的6次异常事件.据推测, 2012年的小碎片碰撞事件,是随后几年燃油泄漏的导火索. 2017年之后剩余燃油完全释放,再也没有出现转速异常.将2014年太阳能帆板损坏和2016年的解体事件后建立的旋转动力学模型外推1 yr,转轴的标准偏差小于3°,转速标准偏差为0.11°·s^(-1),能够有效地满足捕获任务时刻旋转状态的精度要求.

Kinetic Spectrophotometric Determination of Trace Titanium(Ⅳ) Based on Oxidation Discoloration of Acid Chrome Blue K with Hydrogen Peroxide

A simple and sensitive kinetic spectrophotometric method for the determination of trace amounts of titanium(IV),based upon the catalytic effect of Ti(IV) on the oxidation of acid chrome blue K (ACBK) by hydrogen peroxide in 0.002 mol/L sulfuric acid,is described. The reaction rate is monitored spectrophotometrically by measuring the decrease in absorbance of ACBK at 524 nm. The detection limit of the method is 1.01×10?9 g/mL,and the linear range is 0-0.048 mg/L. The influence of acidity,concentration of reactants,reaction time,reaction temperature and for-eign ions is also discussed. The optimum reaction conditions were established and some kinetic parameters determined. The apparent activation energy of the catalytic reaction is 5.32 kJ/mol. The relative standard deviation for the determi-nation of titanium(IV) at the concentration of 0.048 mg/L is calculated to be 1.31% (n = 11). In combination with sol-vent extraction separation,the method has been successfully applied to the determination of trace titanium(IV) in human hair,plant matter,tea and rock samples. The results are in good agreement with the certified values with the relative standard deviations (RSD) of 1.4%-3.5%.

Magnetorheological finishing of low-gradient curved surfaces based on four-axis linkage technique

Based on the distribution characteristic of magnetic field along the polish wheel,the four-axis linkage technique is advanced to replace a standard five-axis one to figure low-gradient optical surfaces with a raster tool-path in magnetorheological finishing(MRF).After introducing the fundaments of such simplification,the figuring reachability of a four-axis system for the low-gradient optics was theoretically analyzed.Further validation including magnetic field intensity and influence function characteristic was performed to establish its application.To demonstrate the correctness,feasibility and applicability of such technique,a K4 spherical part was figured by two iterations of MRF with surface form error improved to 0.219λPV and 0.027λRMS.Meanwhile,the surface roughness was also improved a lot in MRF process.These theoretical analyses and experimental results both indicate that high form accuracy and excellent surface quality can be obtained by using the four-axis linkage technique in the process of figuring low-gradient optical elements,and the four-axis linkage system undoubtedly is much more easy to control and much more economical.

Effect of Multiple Coatings of One-step Self-etching Adhesive on Microtensile Bond Strength to Primary Dentin

Objective To investigate the effect of multiple coatings of the one-step self-etching adhesive on immediate microtensile bond strength to primary dentin.Methods Twelve caries-free human primary molars were randomly divided into 2 groups with 6 teeth each.In group 1,each tooth was hemisected into two halves.One half was assigned to control subgroup 1,which was bonded with a single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 1 in which the adhesive was applied three times before light curing.In group 2,the teeth were also hemisected into two halves.One half was assigned to control subgroup 2,which was bonded with the single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 2 in which three layers of adhesive were applied with light curing each successive layer.Microtensile bond strength was immediately tested after specimen preparation.Results When the adhesive was applied three times before light curing,the bond strength of the experimental subgroup 1(n=33,57.49±11.61 MPa) was higher than that of the control subgroup 1(n=31,49.71±11.43 MPa,P<0.05).When using the technique of applying multiple layers of adhesive with light curing each successive layer,no difference of immediate bond strength was observed between the control subgroup 2 and the experimental subgroup 2(P>0.05).Conclusion Multiple coatings of one-step self-etching adhesive can increase the immediate bond strength to primary dentin when using the technique of light-curing after applying three layers of adhesive.

High precision measurement of formaldehyde in air with differential optical absorption spectroscopy

The formaldehyde (HCHO) measurement is described by differential optical absorption spectroscopy (DOAS) technique and the data processing method is discussed in detail, including the selection of retrieval wavelength band, the removing of interfering structures, the steps of data processing and the spectrum dealing with nonlinear method. The HCHO concentra- tion retrieved in different wavelength bands were compared, including relative error, repeatability and detection limit. As a result, the band from 314 to 332 nm was most suitable for the retrieval of HCHO. With these methods, high measurement precision of 1.9% was obtained and the detection limit of HCHO is less than 1.5 ppb. In addition, high linear relativity 0.9999 is achieved by measuring five different concentrations of HCHO with this system.

Effect on Intensity Correlation Time by Input Signal in a Single-Mode Laser with Bias Signal Modulation

The effect on intensity correlation time T by input signal is studied for gain-noise model of a single-mode laser driven by colored pump noise and colored quantum noise with colored cross-correlation with a bias signal modulation in this paper. By using the linear approximation method, we detect that there exists maximum （i.e., resonance） in the curve of the intensity correlation time T upon bias current io when the noise correlation coefficient λ is positive; and there exists minimum （i.e., suppression） in the T-io curve when λ is negative. And whenλ is zero, T increases monotonously with increasing io. Furthermore, the curve of T upon the signal frequency Ω is also studied. Our study shows that no matter what the value of λ is, there exists minimum （i.e., suppression） in the T-Ω curve.

Temperature dependence of excitonic transition in ZnSe/ZnCdSe quantum wells

A theoretical calculation for the temperature dependence of the excitonic transition in ZnSe/ZnOdSe quantum wells is performed. The exciton binding energy is calculated with a variational technique by considering the temperature-dependence parameters. Our results show that the exciton binding energy reduces linearly with temperature increasing. We find that the strain due to lattice mismatch and differential thermal expansion decreases with the temperature increasing.

Technology of Laser Protection and Defrosting Film

A compound coating of electrically conductive and visible transparent film and laser protective film has been developed,this coating has light densities of no less than 4 against 0.53 μm and no less than 3 against 1.06 μm in the range of ±30° angular field.The average transmittance value as high as 60% from 0.4 μm to 0.7 μm has been achieved.The structures of the laser protective filters are compared.The refractive index of a compound material used in the matching layer has been given.Measured results of the laser protective film coating are compared with that of the compound coating.

Science Letters:Controllable high repetition rate gain-switchedNd:YVO_4 microchip laser

We demonstrated a monolithic, compact, diode-pumped gain-switched Nd:YVO4 laser at 1.064 μm wavelength with controllable repetition rate of 1 Hz to 25 kHz. Stable gain-switched pulse train with maximum repetition rate of 25 kHz and pulse width of 16 ns was obtained.

Techniques for DFB Fiber Laser Based Accelerometer

A distributed feedback fiber laser based Bragg grating vibration sensor system is proposed.Demodulated by using an unbalanced M-Z interferometer,experiment demonstrates that the system runs at a sensing sensitivity of about 257.2 rad·s2/m and a resolution of 4.2×10-5 m/s2 for monitoring acceleration.Experimental results show that the phase-shift changes with the acceleration linearly.

High-Speed Road Measurement Systems： Integration of Pavement and General Mapping Laser Technologies

Performing surveys on a single section of a road is quite different from that on a road network. In the first case, the need for performance characteristics of the pavement may be of service to rehabilitation. Surveying a road network, instead, aims to establish service levels, identify deficiencies and priorities and define budgets for maintenance. This challenge needs a methodological approach in order to widen the action plan and optimize the cost-benefit analysis of each asset through the use of preventive maintenance policies. High-speed monitoring systems on the market were specialized towards the necessity of measuring specific performance of the pavement or mapping land （data inventory）. The technological development of instrumentations such as inertial systems and synchronizers has enabled the integration of different devices and the achievement of the best correlation of data. This is the case of the LARAN （laser road analyzer）, whose helpfulness will be presented within a case study in which geometrical data and surface characteristic information-cracks, texture, profiles-were obtained through a unique survey. The cross-analysis resulted efficient for safety purposes and also for the identification of “black points” corresponding to boundary operative conditions of the road with respect to technical standards and recommendations.

Polishing Techniques of Stainless Steel Molding Die for the Slumping Method of Glass Optical Components

In recent years, high precision geometric shape, surface roughness, and cost reduction are required for large glass component molding processes. In this research, the polishing process of stainless steel molding dies used to form thin glass components is investigated. The surface roughness of the polished stainless steel molding die surface is below Rz = 200 nm （P-V） at 15 h polishing with 0.5 % alumina polishing liquid. In the case of polishing process with only the weight of molding die and a polishing pressure of 0.5 kPa, polishing times are approximately 60 h and 20 h, respectively. Final surface roughness polished stainless steel molding die surface with pressure of 0.5 kPa is Rz = 7 nm （P-V）, rms -- 1.6 nm and Ra = 1.4 nm. In a thin glass component manufacturing method, ＂slumping method＂, surface roughness before glass forming is rms = 0.7 nm and Ra = 0.6 nm, and after is rms = 0.7 nm and Ra = 0.6 nm. Therefore, there were no observable changes their surface roughness.

Ion-Velocity Map Imaging Study of Photodissociation Dynamics of Acetaldehyde

The photodissociation dynamics of acetaldehyde in the radical channel CH3＋HCO has been reinvestigated using time-sliced velocity map imaging technique in the photolysis wavelength range of 275-321 nm. The CH3 fragments have been probed via （2＋1） resonance-enhanced multiphoton ionization. Images are measured for CH3 formed in the ground and excited states （v2=0 and 1） of the umbrella vibrational mode. For acetaldehyde dissociation on T1 state after intersystem crossing from S1 state, the products are formed with high translational energy release and low internal excitation. The rotational and vibrational energy of both fragments increases with increasing photodissociation energy. The triplet barrier height is estimated at 3.8814-0.006 eV above the ground state of acetaldehyde.

Technology of fiber-optic temperature sensing and its application in ＆ temperature measuring of gob area

Based on advantages of technology of distributive fiber-optic temperature sensing and specific to its applications in monitoring mine conflagration, the corresponding Processes such as connection arrangement, signal transmission and monitoring were illustrated. As applied in Sitai Coal Mine of Datong Coal Mine Group Co., this method is effective and accurate and could provide reliable gist for monitoring spontaneous combustion in gob area of mines.

Study on the Interaction Between Tangerine Peel and Beer by Absorption Spectrum

This paper presents a new method to study the interaction between tangerine peel and beer by absorption spectrum.The author explores the change laws and the differences of the absorbance on some wave band from the absorption spectrums of tangerine peel and the mixture of tangerine peel and beer. The results show that there is an obvious difference around 323 nm though the absorbance values of the two samples are almost similar in the most bands. The absorbance value of the mixture is obviously greater than that of tangerine peel at 276 nm in the spectrums, and there is a shift of the peak position in the absorption spectrum of the mixture, which shows the differences of the absorbance values and the peak positions of the two samples. Through comparing the characteristics of the two samples' absorption spectrums, a new method for researching new pharmacological action of tangerine peel is presented in this paper. The result indicates that the technology of spectrum analysis will play an important role in the research and development of Chinese herbal pharmacology and new pharmacology.

Observation on the effect of acupoint stimulation on regional cerebral blood flow using near-infrared spectroscopy technology

Objective To observe the effect of acupuncture at Kongzui（孔最LU 6）,Sanyinjiao（三阴交 SP 6） and Zusanli（足三里 ST 36） on cerebral blood oxygenation level and explore the relevance between acupuncture and cerebral blood oxygenation level using near-infrared spectroscopy（NIRS）.Methods Quasi-randomized design（random test sequence） was used.In clinical trial ①,placebo acupuncture was applied at Baihui（百会GV 20） of18 adults.In clinical trial ②,54 adults were divided into three groups with 18 each in which acupuncture was applied at LU 6,SP 6 and ST 36 respectively.Before and after acupuncture,verbal fluency test（VFT） was performed and the blood oxygenation level of cerebral cortex was measured using NIRS.Quantized data was processed with JMP10.0.2 software and SPSS software.Results In clinical trial ①,the mean integral values of cerebral blood oxygenation level were 10.8 mMcm·s and 9.2 mMcm·s respectively before and after acupuncture at GV 20 in placebo acupuncture group.There was no significant difference in the cerebral blood oxygenation level after acupuncture.In clinical trial ②,the mean integral values of cerebral blood oxygen level were18.1 mMcm·s and 8.6 mMcm·s respectively before and after acupuncture at LU 6 in[LU 6]acupuncture group,the cerebral blood oxygenation level was significantly decreased after acupuncture（P = 0.001）.The mean integral values of cerebral blood oxygenation level were 16.1 mMcm·s and 17.4 mMcm·s respectively before and after acupuncture at SP 6 in[SP 6]acupuncture group,the cerebral blood oxygenation level was slightly increased after acupuncture,but the increase was not statistically significant.The mean integral values of cerebral blood oxygenation level were 13.8 mMcnvs and 10.1 mMcnvs respectively before and after acupuncture at ST 36 in[ST 36]acupuncture group,the cerebral blood oxygenation level was slightly deceased after acupuncture,but the increase was not statistically significant.Conclusion The cerebral blood oxygenation level of frontal head was decreased by acupuncture at LU 6,the cerebral blood oxygenation level of frontal head was intended to decrease by acupuncture at ST 36.The cerebral blood oxygenation level of frontal head is intended to increase by acupuncture at SP 6.

Ozone profiles retrieval from SCIAMACHY Chappuis-Wulf limb scattered spectra using MART

The Scanning Imaging Absorption spectroMeter for Atmospheric ChartographY(SCIAMACHY) instrument,launched on the Envisat satellite in March 2002,measures the earthshine radiance,simultaneously from the ultraviolet(UV) to the near infrared(NIR),in the three viewing geometries:nadir,limb,and occultation.These measurements are used to retrieve both the total amount and vertical profiles of a large number of atmospheric constituents.In this paper,stratospheric ozone profiles between 15 and 40 km altitude are retrieved on 3 km grids from SCIAMACHY limb scattered radiance in the Chappuis-Wulf band.The study employs a new multiplicative algebraic reconstruction technique(MART) coupled with the radiative transfer model SCIATRAN.This technique is outstanding in that more than one measurement vector element can be used to retrieve the ozone density at any altitude.Furthermore,it is straightforward to understand,easy to implement and likely to produce stable results.Radiance normalization and wavelength pairing is applied to radiance as an intermediate step,using the wavelengths 525 nm,600 nm and 675 nm.The sensitivity of ozone retrieval by this method to tangent altitude pointing,surface albedo,aerosol and cloud parameters is studied,and the results show that the retrieval impact due to tangent altitude pointing bias is the biggest up to 75% with 1 km shift,and the impact of albedo is limited within 5%.The effect of boundary visibility and cloud parameters can be ignored since their impact is too small.The effectiveness of the retrieval is demonstrated using a set of coincident SCIAMACHY products at Hefei that shows a mean bias of less than 12% between 15 and 40 km,and with a better accuracy of 5% from 16 to 36 km.

Direct prejudgement of hot images with detected diffraction rings in high power laser system

A direct prejudgement strategy that takes the diffraction ring as the analysis target is put forward to predict hot images induced by defects of tens of microns in the main amplifier section of high power laser systems. Analysis of hot-image formation process shows that the hot image can be precisely calculated with the extracted intensity oscillation of the diffraction ring on the front surface of the nonlinear plate. The gradient direction matching （GDM） method is adopted to detect diffraction tings. Recognition of simulated diffraction rings shows that it is feasible to directly prejudge hot images induced by those closely spaced defects and the defects that are far apart from each other. Image compression and cluster analysis are utilized to optimize the performance of the GDM method in recognizing actually collected diffraction images. Results show that hot images induced by defects of tens of microns can be directly prejudged without redundant information.

Turbulent hydrodynamics experiments in high energy density plasmas： scientific case and preliminary results of the TurboHEDP project

The physics of compressible turbulence in high energy density(HED) plasmas is an unchartered experimental area.Simulations of compressible and radiative flows relevant for astrophysics rely mainly on subscale parameters. Therefore,we plan to perform turbulent hydrodynamics experiments in HED plasmas(TurboHEDP) in order to improve our understanding of such important phenomena for interest in both communities: laser plasma physics and astrophysics. We will focus on the physics of supernovae remnants which are complex structures subject to fluid instabilities such as the Rayleigh–Taylor and Kelvin–Helmholtz instabilities. The advent of megajoule laser facilities, like the National Ignition Facility and the Laser Megajoule, creates novel opportunities in laboratory astrophysics, as it provides unique platforms to study turbulent mixing flows in HED plasmas. Indeed, the physics requires accelerating targets over larger distances and longer time periods than previously achieved. In a preparatory phase, scaling from experiments at lower laser energies is used to guarantee the performance of future MJ experiments. This subscale experiments allow us to develop experimental skills and numerical tools in this new field of research, and are stepping stones to achieve our objectives on larger laser facilities. We review first in this paper recent advances in high energy density experiments devoted to laboratory astrophysics. Then we describe the necessary steps forward to commission an experimental platform devoted to turbulent hydrodynamics on a megajoule laser facility. Recent novel experimental results acquired on LULI2000, as well as supporting radiative hydrodynamics simulations, are presented. Together with the development of LiF detectors as transformative X-ray diagnostics, these preliminary results are promising on the way to achieve micrometric spatial resolution in turbulent HED physics experiments in the near future.

Hybrid 1D/2D heterostructure with electronic structure engineering toward high-sensitivity and polarization-dependent photodetector

The widespread application of photodetectors has triggered an urgent need for high-sensitivity and polarization-dependent photodetection.In this field,the two-dimensional(2D)tungsten disulfide(WS_(2))exhibits intriguing optical and electronic properties,making it an attractive photosensitive material for optoelectronic applications.However,the lack of an effective built-in electric field and photoconductive gain mechanism in 2D WS_(2)impedes its application in high-performance photodetectors.Herein,we propose a hybrid heterostructure photodetector that contains 1D Te and 2D WS_(2).In this device,1D Te induces in-plane strain in 2D WS_(2),which regulates the electronic structures of local WS_(2)and gives rise to type-Ⅱ band alignment in the horizontal direction.Moreover,the vertical heterojunction built of 2D WS_(2)and 1D Te introduces a high photoconductive gain.Benefiting from these two effects,the transfer of photogenerated carriers is optimized,and the proposed photodetector exhibits high sensitivity(photoresponsivity of ~27.7 A W^(-1),detectivity of 9.5×10^(12)Jones,and short rise/decay time of 19.3/17.6 ms).In addition,anisotropic photodetection characteristics with a dichroic ratio up to 2.1 are achieved.This hybrid 1D/2D heterostructure overcomes the inherent limitations of each material and realizes novel properties,opening up a new avenue towards constructing multifunctional optoelectronic devices.