体外肝素抗凝度测定及其在体外循环心内直视手术的临床应用

目的：术前判定患者对肝素的敏感程度，决定能否施行体外循环下的心内直视手术。方法：体外肝素抗凝度检测。结果：本法与活化凝血时间（ＡＣＴ）法比较，具有较高的精密度及特异性。体外肝素化，肝素钙１～１５ｍｇ／ｋｇ体重范围内，具有良好线性关系，与ＡＣＴ法检测结果比较显著相关（ｒ＝０．９９６７）。结论：本法可用以预测患者对肝素的敏感程度。

华法林抗凝时PT-INR与APTT的相关性

目的:了解华法林抗凝治疗时PT-INR与APTT的相关性。方法:对169例用华法林抗凝治疗患者的APTT及PT-INR进行了直线相关与回归分析。结果:在不同的抗凝度时,PT-INR与APTT呈正相关,其直线回归方程分别为:低度抗凝时:APTT=8.153+18.368INR;适度抗凝时:APTT=22.359+9.0602INR;高度抗凝时:APTT=-24.782+25.478INR。结论:华法林治疗时APTT随着PT-INR的变化而变化。

Mechanical properties of anti-seepage grouting materials for heavy metal contaminated soil

Cement-based composite grouting materials were used to construct grouting cutoff wall for heavy metal contaminated soil in non-ferrous metal mining areas. Cement, fly ash, and slag as principal ingredients were mixed with water glass in different ways to produce three composite grouting materials. In order to investigate the effect of water glass mixing ratio, Baume degree, fly ash and slag contents on the mechanical properties of the composite grouting materials, particularly their gel time and compressive strength, the beaker-to-beaker method of gel time test and unconfined compressive strength test were conducted. In addition, the phase composition and microstructure of the composite grouting materials were analyzed by the X-ray diffraction（XRD） and scanning electron microscope（SEM） techniques. The test results show that their gel time increases when water glass mixing ratio and Baume degree increase. The gel time increases dramatically when fly ash is added, but decreases slightly if fly ash is partly replaced by slag. When the mixing ratio of water glass is below 20%, their compressive strength increases with the increases of the ratio; when the ratio is above 20%, it significantly decreases. The compressive strength also tends to increase as Baume degree increases, and improves if fly ash and slag are added.

Calculation on uniaxial compressive strength of high strength concrete after wrapped by FRP

A theoretical calculation method of the axial compressive strength of a high strength concrete with fibre reinforced plastics (FRP) constraint is proposed. It is shown by test verification that the FRP strength devotion factor used for this method is in accordance with actual conditions. FRP is not up to the ultimate strength when the concrete reaches the ultimate strength, whose strength devotion factor is in the range of 0.28 to 0.59, which is related to an elastic modulus. The method can be used to estimate axial compressive strength of the concrete strengthened with FRP. The theoretical strength is 10% to 30% higher than the measured one. The deviation comes mainly from a non-ideal bonding condition of FRP-concrete interfaces and discrete property of the testing data of compressive strength.

Mechanical properties of pervious cement concrete

Compressive and flexural strength,fracture energy,as well as fatigue property of pervious cement concrete with either supplementary cementitious materials (SCMs) or polymer intensified,were analyzed.Test results show that the strength development of SCM-modified pervious concrete (SPC) differs from that of polymer-intensified pervious concrete (PPC),and porosity has little effect on their strength growth.PPC has higher flexural strength and remarkably higher flexural-to-compressive strength ratio than SPC at the same porosity level.Results from fracture test of pervious concrete mixes with porosity around 19.5% show that the fracture energy increases with increasing the dosage of polymer,reflecting the ductile damage features rather than brittleness.PPC displays far longer fatigue life than SPC for any given failure probability and at any stress level.It is proved that two-parameter Weibull probability function describes the flexural fatigue of pervious concrete.

Effect of Recycled Coarse Aggregate on Concrete Compressive Strength

The effect of recycled coarse aggregate on concrete compressive strength was investigated based on the concrete skeleton theory. For this purpose, 30 mix proportions of concrete with target cube compressive strength ranging from 20 to 60 MPa were cast with normal coarse aggregate and recycled coarse aggregate from different strength parent concretes. Results of 28-d test show that the strength of different types of recycled aggregate affects the concrete strength obviously. The coarse aggregate added to mortar matrix plays a skeleton role and improves its compressive strength. The skeleton effect of coarse aggregate increases with the increasing strength of coarse aggregate, and normal coarse aggregate plays the highest, whereas the lowest concrete strength occurs when using the weak recycled coarse aggregate. There is a linear relationship between the concrete strength and the corresponding mortar matrix strength. Coarse aggregate skeleton formula is established, and values from experimental tests match the derived expressions.

Strength of copolymer grouting material based on orthogonal experiment

Using the orthogonal experimental design method involving three factors and three levels, the flexural strength and the compressive strength of copolymer grouting material were studied with different compositions of water-cement ratio （mass fraction of water to cement）, epoxy resin content, and waterborne epoxy curing agent content. By orthogonal range and variance analysis, the orders of three factors to influence the strength, the significance levels of different factors, and the optimized compound ratio scheme of copolymer grouting material mixture at different curing ages were determined. An empirical relationship among the strength of copolymer grouting material, the water-cement ratio, the epoxy resin content, and the waterborne epoxy curing agent content was established by multivariate regression analysis. The results indicate that water-cement ratio is the most principal and significant influencing factor on the strength. Epoxy resin content and waterbome epoxy curing agent content also have a significant influence on the strength. But epoxy resin content has a greater influence on the 7-day and 28-day flexural strength, and waterborne epoxy curing agent content has a greater influence on the 3-day flexural strength and the compressive strength. The copolymer grouting material with water-cement ratio of 0.4, epoxy resin content of 8% （mass fraction） and waterbome epoxy curing agent content of 2% （mass fraction） is the best one for repairing of cement concrete pavement. The flexural strength and the compressive strength have good correlation, and the ratio of compressive strength to flexural strength is between 1.0 and 3.3.

Performance of Cross-Shaped Concrete Columns Confined by Stirrups

The stress-strain curves of confined concrete were obtained based on tests of seven cross-shaped columns confined by stirrups under axial load. The experiment results showed that the strength and deformation of confined concrete can be enhanced effectively by stirrups for cross-shaped columns. Compared with the non-confined concrete, when the stirrup characteristic value is in the range of 0.046-0.230, the confined concrete compressive strengths has an increase of 8%-43%, and the strain corresponding to the peak stress of confined concrete has an increase of 25%-195%. According to the test results, the effects of stirrup characteristic and stirrup spacing on the compressive strength and strain of confined concrete were analysed. It is shown that the compressive strength of confined concrete has a linear relationship with the product of stirrup characteristic value and stirrup effective restraint coefficient, and the strain corresponding to the peak stress of confined concrete has a nonlinear relationship with the product of stirrup characteristic value and stirrup effective restraint coefficient. The stress-strain curve equation of confined concrete was proposed for cross-shaped columns, and the calculated curves are in good agreement with the experimental curves.

Stress-strain behavior of plastic concrete using monotonic triaxial compression tests

The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures have been done and the stress-strain behavior of such materials and their strength parameter changes have been experimentally investigated. It has been observed that increasing the confining pressures applied on the specimens causes the material behavior to be alike the more ductile materials and the compressive strength increases considerably as well. Moreover, a parametric study has been carded out to investigate the influence of essential parameters on the shear strength parameters of these materials. According to the research, increasing the coarse to fine aggregates ratio leads to the increase of compressive strength of the specimens as well as the increase of the cohesion and internal friction angle of the materials. Furthermore, the bentonite content decrease and the cement factor increase result in an increase of the cohesion parameter of plastic concretes and decrease of the internal friction angle of such materials.

Seismic ductility of very-high-strength-concrete short columns subject to combined axial loading and cyclic lateral loading

The seismic ductility of reinforced very-high-strength-concrete （VHSC） short columns was studied by combinatively applying axial load and low cyclic lateral load on specimens to simulate seismic impact. Twelve specimens with concrete compressive strength ranging from 95.6 MPa to 118.6 MPa and a shear-span ratio of 2.0 were tested for shear failure pattern and fear force-displacement hysteretic responses. Combinative application of axial load and low cyclic lateral load to VHSC short columns incurs shear failure. The displacement ductility is much smaller when the axial load ratio is larger; whereas a larger stirrup ratio is accompanied with a better displacement ductility. The relationship of displacement ductility factor,μ△, with stirrup characteristic value, λv, and test axial load ratio, nt, is μ△=（1＋8λv）/（0.33＋nt）. By this relationship and relevant codes for aseismatic design, the axial load ratio limits for aseismatic design of reinforced VHSC （C95 to C100） short columns for frame construction are respectively 0.5, 0.6, and 0.7 for seismic classes Ⅰ, Ⅱ, and Ⅲ; corresponding minimum characteristic values of stirrups are calculated according to the required characteristic values of at least 1.273 times of experimental results. These data are very useful to aseismatic engineering.

Modified imperialist competitive algorithm-based neural network to determine shear strength of concrete beams reinforced with FRP

Fiber reinforced polymers (FRPs), unlike steel, are corrosion-resistant and therefore are of interest;however, their use is hindered because their brittle shear is formulated in most specifications using limited data available at the time. We aimed to predict the shear strength of concrete beams reinforced with FRP bars and without stirrups by compiling a relatively large database of 198 previously published test results (available in appendix). To model shear strength, an artificial neural network was trained by an ensemble of Levenberg-Marquardt and imperialist competitive algorithms. The results suggested superior accuracy of model compared to equations available in specifications and literature.

Preparation and properties of geopolymer-lightweight aggregate refractory concrete

Geopolymer-lightweight aggregate refractory concrete (GLARC) was prepared with geopolymer and lightweight aggregate. The mechanical property and heat-resistance (950 ℃) of GLARC were investigated. The effects of size of aggregate and mass ratio of geopolymer to aggregate on mechanical and thermal properties were also studied. The results show that the highest compressive strength of the heated refractory concrete is 43.3 MPa,and the strength loss is only 42%. The mechanical property and heat-resistance are influenced by the thickness of geopolymer covered with aggregate,which can be expressed as the quantity of geopolymer on per surface area of aggregate. In order to show the relationship between the thickness of geopolymer covered with aggregate and the thermal property of concrete,equal thickness model is presented,which provides a reference for the mix design of GLARC. For the haydite sand with size of 1.18-4.75 mm,the best amount of geopolymer per surface area of aggregate should be in the range of 0.300-0.500 mg/mm2.

Key Technologies in the Design and Construction of 300 m Ultra-High Arch Dams

Starting with the Ertan arch dam （240 m high, 3300 MW） in 2000, China successfully built a total of seven ultra-high arch dams over 200 m tall by the end of 2014. Among these, the ]inping 1 （305 m）, Xiaowan （294.5m）, and Xiluodu （285.5 m） arch dams have reached the 300 m height level （i.e., near or over 300 m）, making them the tallest arch dams in the world. The design and construction of these 300 m ultra-high arch dams posed significant challenges, due to high water pressures, high seismic de- sign criteria, and complex geological conditions. The engineering team successfully tackled these chal- lenges and made critical breakthroughs, especially in the area of safety control. In this paper, the author summarizes various key technological aspects involved in the design and construction of 300 m ultra- high arch dams, including the strength and stability of foundation rock, excavation of the dam base and surface treatment, dam shape optimization, safety design guidelines, seismic analysis and design, treatment of a complex foundation, concrete temperature control, and crack prevention. The experience gained from these projects should be valuable for future practitioners.

Cemented backfill technology based on phosphorous gypsum

Physical-chemical properties of phosphorous gypsum, proportion and cemented mechanism of slurry with gypsum as aggregate were studied to remove the harms of gypsum pile, combining with difficult problems of excessive mined-out gobs, enormous ore body under roadway and low recovery ratio of Yongshaba Mine, Kaiyang Phosphor Mine Group, Guizhou Province, China. An appropriate backfill system and craflwork were designed, using shattering milling method to crush gypsum, double-axles mixing and strong activation mixing way to mix slurry, cemented slurry and mullock backfill alternately process. The results show that gypsum is fit for backfilling afterwards by adding fly ash, though it is not an ideal aggregate for fine granule and coagulate retardation. The suggested dosage （the mass ratio of cement to fly ash to gypsum） is 1：1：6-1：1：8 with mass fraction of solid materials 60%-63%. Slurry is transported in suspend state with non-plastic strength, and then in concretion state after backfilling. The application to mine shows the technology is feasible, and gypsum utilization ratio is up to 100%. Transportation and backfill effect is very good for paste-like slurry and drenching cemented slurry into mullock, and the compressive strength and recovery ratio are 2.0 MPa and 82.6%, respectively, with the maximum subsidence of surface only 1.307 mm. Furthermore, the investment of system is about 7 × 10^6 yuan （RMB）, only 1/10 of that of traditional paste backfill system.

A Statistical Analysis of the Modulus of Elasticity and Compressive Strength of Concrete C45/55 for Pre-stressed Precast Beams

Random behavior of concrete C45/55 XF2 used for prefabricated pre-stressed bridge beams is described on the basis of evaluating a vast set of measurements. A detailed statistical analysis is carried out on 133 test results of cylinders 150 ~ 300 mm in size. The tests have been running in laboratories of the Klokner Institute. A single worker took all specimens throughout the period, and the subsequent measurements of the static modulus of elasticity and the compressive strength of the concrete were performed. The measurements were made at the age of 28 days after specimens casting, and only one testing machine with the same capping method was used. Suitable theoretical models of division are determined on the basis of tests in good congruence, with the use of Z2 and the Bernstein criterion. A set of concrete compressive strength （carried out on 133 test results of cylinders 150 ~ 300 mm after test of static modulus of elasticity） shows relatively high skewness in this specific case. This cause that limited beta distribution is better than generally recommended theoretical distribution for strength the normal or lognormal. The modulus of elasticity is not significantly affected due to skewness because the design value is based on mean value.

Water Permeability in Fly Ash-Based Geopolymer Concrete

This research investigated the water permeability coefficient of fly ash-based geopolymer concrete. The effect of sodium hydroxide （Na（OH）） concentrations and Si/AI ratios on water permeability and compressive strength of geopolymer concretes were studied. The geopolymer concrete were prepared from Mae Moh fly ash with sodium silicate （Na2SiO3） and sodium hydroxide （Na（OH）） solutions. In the first group, concentration of Na（OH） was varied at 8, 10, 12, and 14 molar and the Si/AI ratio was kept constant at 1.98. In the second group, a concentration of Na（OH） was kept constant at 14 molar and the Si/AI ratio was varied at 2.2, 2.4, 2.6, and 2.8. The hardened concretes were air-cured in laboratory. The compressive strength and water permeability were tested at the age of 28 and 60 days. The results showed that compressive strengths of geopolymer concrete significantly increased with the increase of a concentration of Na（OH） and Si/AI ratio. The water permeability coefficients increase with the decrease of compressive strength. In addition, the high reduction of water permeability coefficients with time was found in geopolymer concrete with lower Na（OH） concentration than that higher Na（OH） concentration.

Behavior of Reinforced Concrete Columns under Combined Axial Load and Bending in Accordance with a Nonlinear Numerical Model

A nonlinear numerical model was developed to analyze reinforced concrete columns under combined axial load and bending up to failure. Results of reinforced concrete columns under eccentric compression tested to failure are presented and compared to results from a numerical nonlinear model. The tests involved 10 columns with cross-section of 250 mm × 120 mm, geometrical reinforcement ratio of 1.57% and concrete with compression strength around 40 MPa, with 3,000 mm in length. The main variable was the load eccentricity in the direction of the smaller dimension of cross-section. Experimental results of ultimate load and of the evolution of transverse displacements and concrete strains are compared with the numerical results. The estimated results obtained by the numerical model are close to the experimental ones, being suitable for use in verification of elements under combined axial load and bending.

Effect of waste concrete with different strength on mechanical properties of recycled fine aggregate mortar

The influence of source concrete (SC) with different compression strengths on the workability and mechanical properties of recycled mortar made with river sand substituted by 100% fine recycled concrete aggregates (FRCA) is experimentally investigated. The basic physical performance test shows that with the increase in SC strength, FRCA exhibit lower water absorption and crushing index, meanwhile keeping higher densities. Mechanical property tests, including compressive strength, flexural strength and uniaxial compressive stress-strain tests, show that compressive strength,flexural strength and elasticity modulus of recycled sand mortars increase roughly with the increase in SC strength. The proposed mixture design method demonstrates that all of the components can be kept as the same as those in natural mortar mixture design and FRCA must be pre-wetted before making mortar mixture. Meanwhile, the reuse of higher strength SC can ensure that recycled mortar mixtures are able to achieve similar mechanical performance when compared to natural mortar designs.

Effect of elevated-temperature annealing on microstructure and properties of Cu−0.15Zr alloy

Cu−0.15Zr(wt.%)alloy with uniform and fine microstructure was fabricated by rapid solidification followed by hot forging.Evolution of microstructure,mechanical properties and electrical conductivity of the alloy during elevated-temperature annealing were investigated.The alloy exhibits good thermal stability,and its strength decreases slightly even after annealing at 700℃ for 2 h.The nano-sized Cu_(5)Zr precipitates show significant pinning effect on dislocation moving,which is the main reason for the high strength of the alloy.Additionally,the large-size Cu_(5)Zr precipitates play a major role in retarding grain growth by pinning the grain boundaries during annealing.After annealing at 700℃ for 2 h,the electrical conductivity of samples reaches the peak value of 88%(IACS),which is attributed to the decrease of vacancy defects,dislocations,grain boundaries and Zr solutes.

Experimental investigation on strength and deformation of plain high-strength concrete under multiaxial stress state

To investigate the strength and deformation behavior of plain high-strength concrete （HSC） under muhiaxial stress states, a large static-dynamic true triaxial machine was employed, and muhiaxial tests were performed on 100 mm × 100 mm × 100 mm cubes concrete specimens. Friction-reducing pads were three-layer plastic membranes with glycerine in-between for the compressive loading plane. The tensile loading plane of concrete samples was processed by attrition machine, and then the samples were glued up with the loading plate with structural glue. Failure modes of specimens were described. The principal static compressive strengths, strains at the peak stress and stress-strain curves were measured, and the influence of stress ratios on them was analyzed as well. Experimental results show that the ratio of the compressive strength σ3f over the uniaxial compressive strengthfo depends on brittleness-stiffness of concrete besides stress state and stress ratios. The formula of Kupfer-Gerstle＇ s and Ottosen＇ s failure criterion for plain HSC under biaxial compression and muhiaxial stress state is proposed respectively.