黏粒含量对砂土抗剪强度影响的试验研讨

分析砂土黏粒的粒度,可以确定土地内部固相颗粒大小,利用试验可以测定黏粒含量的砂土摩擦角,建立复核多项式关系,黏粒含量增加,土体抗剪强度首先会降低,随后再升高,这是因为黏粒在土地当中,首先发挥的是滚珠作用,其次会发挥骨架作用。本文主要分析了黏粒含量对砂土抗剪强度影响的试验,从而充分利用黏粒含量的作用。

Effects of Al-Ti-B-RE grain refiner on microstructure and mechanical properties of Al-7.0Si-0.55Mg alloy

To investigate the effects of Al-Ti-B-RE grain refiner on microstructure and mechanical properties of Al-7.0Si-0.55Mg （A357） alloy, some novel Al-7.0Si-0.55Mg alloys added with different amount of Al-STi-1B-RE grain refiner with different RE composition were prepared by vacuum-melting. The microstructure and fracture behavior of the AI-7.0Si-0.55Mg alloys with the grain refiners were observed by X-ray diffraction （XRD）, optical microscopy （OM）, scanning electron microscopy （SEM）, and the mechanical properties of the alloys were tested in mechanical testing machine at room temperature. The observation of AI-Ti-B-RE morphology and internal structure of the particles reveals that it exhibits a TiAl3/Ti2Al20RE core-shell structure via heterogeneous TiB2 nuclei. The tensile strength of Al-7.0Si-0.55Mg alloys with Al-5Ti-1B-3.0RE grain refiner reaches the peak value at the same addition （0.2%） of grain refiner.

Effect of chloride salt concentration on unconfined compression strength of cement-treated Lianyungang soft marine clay

This study aims to quantify the influence of the amount of cement and chloride salt on the unconfined compression strength （UCS） of Lianyungang marine clay. The clays with various sodium chloride salt concentrations were prepared artificially and stabilized by ordinary Portland cement with various contents. A series of UCS tests of cement stabilized clay specimen after 28 d curing were carried out. The results indicate that the increase of salt concentration results in the decrease in the UCS of cement-treated soil. The negative effect of salt concentration on the strength of cement stabilized clay directly relates to the cement content and salt concentration. The porosity-salt concentration/cement content ratio is a fundamental parameter for assessing the UCS of cement-treated salt-rich clay. An empirical prediction model of UCS is also proposed to take into account the effect of salt concentration. The findings of this study can be referenced for the stabilization improvement of chloride slat- rich soft clay.

Influence of Gradient on Stability of Soil Slope Containing Roots

Abundant herbaceous and shrub roots play an important role in preventing water and soil erosion and increasing shallow slope stability. In order to make a quantitative analysis on the contribution of root system to slope stability under dif- ferent slope gradient, an unconsolidated and undrained triaxial compression test was conducted to measure the shear strengths of soil and root-soil composite in the two slopes in eastern Qinghai Province. In addition, under the protection of plant roots, the effect of gradient on stability of soil slope was investigated by limit equilibrium method. The results showed that the stability coefficient of soil slope planted with two kinds of brush was decreased with the increase in slope gradient, and the sta- bility coefficient increment of soil slope containing Atriplex canescens roots was higher than that containing Caragana korshinskii roots. When the slope gradient ranged from 25° to 50°, the stability coefficient of soil slope planted with Atriplex canescens or Caragana korshinskii ranged from 0.80 to 1.38. However, when the slope gradient exceeded 55°, the increment of stability coefficient of soil slope became small.

Calculation on uniaxial compressive strength of high strength concrete after wrapped by FRP

A theoretical calculation method of the axial compressive strength of a high strength concrete with fibre reinforced plastics (FRP) constraint is proposed. It is shown by test verification that the FRP strength devotion factor used for this method is in accordance with actual conditions. FRP is not up to the ultimate strength when the concrete reaches the ultimate strength, whose strength devotion factor is in the range of 0.28 to 0.59, which is related to an elastic modulus. The method can be used to estimate axial compressive strength of the concrete strengthened with FRP. The theoretical strength is 10% to 30% higher than the measured one. The deviation comes mainly from a non-ideal bonding condition of FRP-concrete interfaces and discrete property of the testing data of compressive strength.

Water-induced changes in strength characteristics of polyurethane polymer and polypropylene fiber reinforced sand

As a new kind of air-hardening soil reinforcement material,polymer is being widely applied in river-bank slope reinforcement and ecological slope protection area.Thus,more attention should be paid to study the characteristics of reinforced soil after immersion.In this study,water-induced changes in strength characteristics of sand reinforced with polymer and fibers were reported.Several factors,including polymer content(1%,2%,3%and 4%by weight of dry sand),immersion time(6,12,24 and 48 h),dry density(1.40,1.45,1.50,1.55 and 1.60 g/cm^(3),)and fiber content(0.2%,0.4%,0.6%and 0.8%by weight of dry sand)which may influence the strength characteristics of reinforced sand after immersion were analyzed.The microstructure of reinforced sand was analyzed with nuclear magnetic resonance(NMR)and scanning electron microscope(SEM).Experimental results indicate that the compressive strength increases with the increase of polymer content and decreases with the increase of immersion time;the softening coefficients decrease with the increase of the polymer content and immersion time and increase with an increment in density and fiber content.Fiber plays an active role in reducing water-induced loss of strength at 0.6%content.

Strength of copolymer grouting material based on orthogonal experiment

Using the orthogonal experimental design method involving three factors and three levels, the flexural strength and the compressive strength of copolymer grouting material were studied with different compositions of water-cement ratio （mass fraction of water to cement）, epoxy resin content, and waterborne epoxy curing agent content. By orthogonal range and variance analysis, the orders of three factors to influence the strength, the significance levels of different factors, and the optimized compound ratio scheme of copolymer grouting material mixture at different curing ages were determined. An empirical relationship among the strength of copolymer grouting material, the water-cement ratio, the epoxy resin content, and the waterborne epoxy curing agent content was established by multivariate regression analysis. The results indicate that water-cement ratio is the most principal and significant influencing factor on the strength. Epoxy resin content and waterbome epoxy curing agent content also have a significant influence on the strength. But epoxy resin content has a greater influence on the 7-day and 28-day flexural strength, and waterborne epoxy curing agent content has a greater influence on the 3-day flexural strength and the compressive strength. The copolymer grouting material with water-cement ratio of 0.4, epoxy resin content of 8% （mass fraction） and waterbome epoxy curing agent content of 2% （mass fraction） is the best one for repairing of cement concrete pavement. The flexural strength and the compressive strength have good correlation, and the ratio of compressive strength to flexural strength is between 1.0 and 3.3.

Stress-strain behavior of plastic concrete using monotonic triaxial compression tests

The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures have been done and the stress-strain behavior of such materials and their strength parameter changes have been experimentally investigated. It has been observed that increasing the confining pressures applied on the specimens causes the material behavior to be alike the more ductile materials and the compressive strength increases considerably as well. Moreover, a parametric study has been carded out to investigate the influence of essential parameters on the shear strength parameters of these materials. According to the research, increasing the coarse to fine aggregates ratio leads to the increase of compressive strength of the specimens as well as the increase of the cohesion and internal friction angle of the materials. Furthermore, the bentonite content decrease and the cement factor increase result in an increase of the cohesion parameter of plastic concretes and decrease of the internal friction angle of such materials.

Effect of Recycled Coarse Aggregate on Concrete Compressive Strength

The effect of recycled coarse aggregate on concrete compressive strength was investigated based on the concrete skeleton theory. For this purpose, 30 mix proportions of concrete with target cube compressive strength ranging from 20 to 60 MPa were cast with normal coarse aggregate and recycled coarse aggregate from different strength parent concretes. Results of 28-d test show that the strength of different types of recycled aggregate affects the concrete strength obviously. The coarse aggregate added to mortar matrix plays a skeleton role and improves its compressive strength. The skeleton effect of coarse aggregate increases with the increasing strength of coarse aggregate, and normal coarse aggregate plays the highest, whereas the lowest concrete strength occurs when using the weak recycled coarse aggregate. There is a linear relationship between the concrete strength and the corresponding mortar matrix strength. Coarse aggregate skeleton formula is established, and values from experimental tests match the derived expressions.

Modified imperialist competitive algorithm-based neural network to determine shear strength of concrete beams reinforced with FRP

Fiber reinforced polymers (FRPs), unlike steel, are corrosion-resistant and therefore are of interest;however, their use is hindered because their brittle shear is formulated in most specifications using limited data available at the time. We aimed to predict the shear strength of concrete beams reinforced with FRP bars and without stirrups by compiling a relatively large database of 198 previously published test results (available in appendix). To model shear strength, an artificial neural network was trained by an ensemble of Levenberg-Marquardt and imperialist competitive algorithms. The results suggested superior accuracy of model compared to equations available in specifications and literature.

Shear strength of clayey sand treated by nanoclay mixed with recycled polyester fiber

The main objective of this study is to investigate the effects of the nanoclay mixed with recycled polyester fiber on the mechanical behavior of soil as a new stabilizer material.To meet this objective,a series of drained direct shear and compaction tests were performed on unreinforced and reinforced soil specimens with three different combinations of the fiber-soil ratios ranging between 0.1%and 0.5%,as well as three different combinations of nanoclay soil ratios ranging between 0.5%and 1.5%of the soil dry weight.Results indicated that composition of the nanoclay recycled polyester fiber with the soil improved the friction angle(Φ)by 41%and cohesion(c)by 174%.The soil particles stick together through viscose gel produced by nanoclay.In addition,the rough and wavy surface of the fibers creates a bond and friction between the soil particles and prevents the movement of soil particles,and as a result,the soil strength is increased.

Performance of Cross-Shaped Concrete Columns Confined by Stirrups

The stress-strain curves of confined concrete were obtained based on tests of seven cross-shaped columns confined by stirrups under axial load. The experiment results showed that the strength and deformation of confined concrete can be enhanced effectively by stirrups for cross-shaped columns. Compared with the non-confined concrete, when the stirrup characteristic value is in the range of 0.046-0.230, the confined concrete compressive strengths has an increase of 8%-43%, and the strain corresponding to the peak stress of confined concrete has an increase of 25%-195%. According to the test results, the effects of stirrup characteristic and stirrup spacing on the compressive strength and strain of confined concrete were analysed. It is shown that the compressive strength of confined concrete has a linear relationship with the product of stirrup characteristic value and stirrup effective restraint coefficient, and the strain corresponding to the peak stress of confined concrete has a nonlinear relationship with the product of stirrup characteristic value and stirrup effective restraint coefficient. The stress-strain curve equation of confined concrete was proposed for cross-shaped columns, and the calculated curves are in good agreement with the experimental curves.

Study on the shear strength of deep reconstituted soils

Based on analytical methods of strength studies for deep soils, direct shear tests were carried out to investigate the shear strength of deep reconstituted soils at different initial dry densities and amounts of water.The results indicate that the shear strength of deep reconstituted soils for identical amounts of water below the plastic limit is enhanced with increasing dry density and but reduced sharply at the critical density, the point at which coarse particles break down.Moreover, the shear strength for identical dry density decreases with additional amounts of water and the rate of degradation is the greatest at the critical density.This is because the friction resistance between coarse particles reduces with increasing amounts of water higher than the plastic limit.In order to obtain reliable strength of deep reconstituted soils, suitable dry densities and amounts of water are necessary.

Shear strength features of soils developed from purple clay rock and containing less than two-millimeter rock fragments

Soil shear strength is an important indicator of engineering design and an essential parameter of soil precision tillage and agricultural machinery and equipment design. Although numerous studies have investigated the characteristics of different soil shear strengths, only a few of these works have paid attention to soils containing considerable quantities of rock fragments. To date, most studies on the effects of rock fragments on the shear strength have paid attention to the role of rock fragments with sizes 〉2 mm. The effects of rock fragments 〈2 mm in soil are generally ignored. Similar to rock fragments 〉2 ram, the presence of rock fragments 〈2 mm could also change the mechanical properties of soils. Thus, in the present study we evaluated the potential influence of 〈2 mm rock fragments on soil shear strength via an unconsolidated undrained （UU） triaxial compression test. Our results were as follows： （1） A certain quantity of 〈2 mm rock fragments presented in purple soils developed from clay rocks; and an appropriate quantity of 〈2 mm rock fragments could improve the shear strength of soils. （2） The different PSDs of soils containin 〈2 mm rock fragment mainly caused variations in the internal friction angle of soils. （3） The shear strengths of the two mudstone-developed red-brown and gray-brown purple soils was more sensitive to water than that of the shale-developed coarse-dark purple soil. As the soil water content increased from 9% to 23%, the changes in the cohesion, internal friction angle, shear strength, and the maximum principal stress difference were smaller in the coarse dark purple soil than in the two other soils. We therefore concluded that 〈2 mm rock fragments in purple soils exerted important effects on soil shear strength. A better understanding of the differences among the shear strength features of purple soils could help improve the design of agricultural machinery and equipment.

Preparation and properties of geopolymer-lightweight aggregate refractory concrete

Geopolymer-lightweight aggregate refractory concrete (GLARC) was prepared with geopolymer and lightweight aggregate. The mechanical property and heat-resistance (950 ℃) of GLARC were investigated. The effects of size of aggregate and mass ratio of geopolymer to aggregate on mechanical and thermal properties were also studied. The results show that the highest compressive strength of the heated refractory concrete is 43.3 MPa,and the strength loss is only 42%. The mechanical property and heat-resistance are influenced by the thickness of geopolymer covered with aggregate,which can be expressed as the quantity of geopolymer on per surface area of aggregate. In order to show the relationship between the thickness of geopolymer covered with aggregate and the thermal property of concrete,equal thickness model is presented,which provides a reference for the mix design of GLARC. For the haydite sand with size of 1.18-4.75 mm,the best amount of geopolymer per surface area of aggregate should be in the range of 0.300-0.500 mg/mm2.

Critical embedment depth of a rigid retaining wall against overturning in unsaturated soils considering intermediate principal stress and strength nonlinearity

The overturning stability is vital for the retaining wall design of foundation pits, where the surrounding soils are usually unsaturated due to water draining. Moreover, the intermediate principal stress does affect the unsaturated soil strength; meanwhile, the relationship between the unsaturated soil strength and matric suction is nonlinear. This work is to present closed-form equations of critical embedment depth for a rigid retaining wall against overturning by means of moment equilibrium. Matric suction is considered to be distributed uniformly and linearly with depth. The unified shear strength formulation for unsaturated soils under the plane strain condition is adopted to characterize the intermediate principal stress effect, and strength nonlinearity is described by a hyperbolic model of suction angle. The result obtained is orderly series solutions rather than one specific answer; thus, it has wide theoretical significance and good applicability. The validity of this present work is demonstrated by comparing it with a lower bound solution. The traditional overturning designs for rigid retaining walls, in which the saturated soil mechanics neglecting matric suction or the unsaturated soil mechanics based on the Mohr-Coulomb criterion are employed, are special cases of the proposed result. Parametric studies about the intermediate principal stress, matric suction and its distributions along with two strength nonlinearity methods on a new defined critical buried coefficient are discussed.

Low secondary compressibility and shear strength of Shanghai Clay

In order to investigate the compressibility, particularly the secondary compression behaviour, soil structure and undrained shear strength of Shanghai Clay, a series of one-dimensional consolidation tests （some up to 70 d） and undrained triaxial tests on high-quality intact and reconstituted soil specimens were carried out. Shanghai Clay is a lightly overconsolidated soil （OCR=1.2-1.3） with true cohesion or bonding. Due to the influence of soil structures, the secondary compression index Ca varies significantly with consolidation stress and the maximum value of C~ occurs in the vicinity of preconsolidation stress. Measured coefficients of secondary compression generally fall in the range of 0.2%-0.8% based on which Shanghai Clay can be classified as a soil with low to medium secondary compressibility. The effect of soil structures on the compressibility of Shanghai Clay is found to reduce with an increase in depth. Soil structure has an important influence on initial soil stiffness, but does not appear to affect undrained shear strength significantly. Undrained shear strengths of intact Shanghai Clay from compression tests are approximately 20% higher than those from extension tests.

Mechanical and electrical properties of coarse-grained soilaffected by cyclic freeze-thaw in high cold regions

To evaluate the geotechnical properties of coarse-grained soil affected by cyclic freeze-thaw,the electrical resistivity and mechanical tests are conducted.The soil specimens are prepared under different water contents,dry densities and exposed to 0?20 freeze-thaw cycles.As a result,the stress?strain behavior of the specimen(w=14.0%andρd=1.90 g/cm^3)changes from strain-hardening into strain-softening due to the freeze-thaw effect.The electrical resistivity of test specimen increases with the freeze-thaw cycles change,but the mechanical parameters(the unconfined compressive strength qu and the deformation modulus E)and brittleness index decrease considerably at the same conditions.All of them tend to be stable after 7?9 cycles.Moreover,both the dry density and the water content have reciprocal effects on the freeze-thaw actions.The failure and pore characteristics of specimens affected by freeze-thaw cycles are discussed by using the image analysis method.Then,an exponential function equation is developed to assess the electrical resistivity of specimens affected by the cyclic freeze-thaw.Linear relations between the mechanical parameters and the electrical resistivity of specimens are established to evaluate the geotechnical properties of the soil exposed to freeze-thaw actions through the corresponding electrical resistivity.

A Statistical Analysis of the Modulus of Elasticity and Compressive Strength of Concrete C45/55 for Pre-stressed Precast Beams

Random behavior of concrete C45/55 XF2 used for prefabricated pre-stressed bridge beams is described on the basis of evaluating a vast set of measurements. A detailed statistical analysis is carried out on 133 test results of cylinders 150 ~ 300 mm in size. The tests have been running in laboratories of the Klokner Institute. A single worker took all specimens throughout the period, and the subsequent measurements of the static modulus of elasticity and the compressive strength of the concrete were performed. The measurements were made at the age of 28 days after specimens casting, and only one testing machine with the same capping method was used. Suitable theoretical models of division are determined on the basis of tests in good congruence, with the use of Z2 and the Bernstein criterion. A set of concrete compressive strength （carried out on 133 test results of cylinders 150 ~ 300 mm after test of static modulus of elasticity） shows relatively high skewness in this specific case. This cause that limited beta distribution is better than generally recommended theoretical distribution for strength the normal or lognormal. The modulus of elasticity is not significantly affected due to skewness because the design value is based on mean value.

Seismic ductility of very-high-strength-concrete short columns subject to combined axial loading and cyclic lateral loading

The seismic ductility of reinforced very-high-strength-concrete （VHSC） short columns was studied by combinatively applying axial load and low cyclic lateral load on specimens to simulate seismic impact. Twelve specimens with concrete compressive strength ranging from 95.6 MPa to 118.6 MPa and a shear-span ratio of 2.0 were tested for shear failure pattern and fear force-displacement hysteretic responses. Combinative application of axial load and low cyclic lateral load to VHSC short columns incurs shear failure. The displacement ductility is much smaller when the axial load ratio is larger; whereas a larger stirrup ratio is accompanied with a better displacement ductility. The relationship of displacement ductility factor,μ△, with stirrup characteristic value, λv, and test axial load ratio, nt, is μ△=（1＋8λv）/（0.33＋nt）. By this relationship and relevant codes for aseismatic design, the axial load ratio limits for aseismatic design of reinforced VHSC （C95 to C100） short columns for frame construction are respectively 0.5, 0.6, and 0.7 for seismic classes Ⅰ, Ⅱ, and Ⅲ; corresponding minimum characteristic values of stirrups are calculated according to the required characteristic values of at least 1.273 times of experimental results. These data are very useful to aseismatic engineering.