带压开采煤层底板的承压能力研究

通过实测资料揭示了煤层底板保护层在一定条件下存在导水和贮水的性能,并剖析了这种性能的水理性质和规律,阐明了起始水力梯度、消压强度、抗水压强度、临界突水系数在概念上的统一性;在此基础上,分析了煤矿突水的机理与模式;并指明了探测研究保护层这一特性在确定开采煤层底板抗水压能力和带压开采安全性等方面的重要意义。

Determination of undrained shear strength using piezocone penetration test in clayey soil for bridge foundation

In order to obtain the reasonable undrained shear strength Su for geotechnical analyses of bridge foundations in Yangtze River floodplain clayey soils, a site-specific study is conducted using the imported piezocone penetration test （CPTu） with dissipation phases at the Fourth Nanjing Yangtze River Bridge construction sites. Taking the values of Su from laboratory tests as references, several existing Su-predicted methods based on CPTu are compared and evaluated. To verify the presented cone factor Nk, additional test sites are selected and examined. The results show that the values of cone factors such as Nkt, Nke, and Nau, depend on the shear test mode and disturbance. Generally, the values of Nke show more scattering than those of Nkt and N△u. For the stratified and layered sediments of the Yangtze River floodplain, it is recommended using the net cone resistance qT to estimate Su and the preliminary cone factor values Nkt are from 7 to 16, with an average of 11. It is also confirmed that the CPTu test, as a new technique in site characterization, can present reasonable parameters for bridge foundations.

冻融循环作用后饱和黏土的应变速率效应试验研究

为研究不同应变速率加载对融化饱和黏土力学效应的影响,对不同初始压实度的融化饱和黏土进行了不同应变速率和围压下的固结不排水三轴剪切试验,分析了融化饱和黏土的应力-应变关系曲线特征、孔隙水压力、割线模量(E_(50))、峰值强度、残余强度、抗剪强度指标的变化规律。结果表明:随着应变速率的增大,融化饱和黏土峰值强度和残余强度均先增大后减小,随后持续增大;而E_(50)模量则一直增大。应变速率未改变偏应力峰值所对应的应变大小;初始压实度不影响融化饱和黏土峰值强度对应的应变值,且在围压为120 k Pa、应变速率为0.15%/h时初始压实度对融化饱和黏土孔隙水压力发展趋势的影响不大,而当应变速率超过1.5%/h时,初始压实度的影响显著。随着围压增大,融化饱和黏土峰值强度对应的应变值及孔隙水压力明显增大。应变速率小于15%/h时,内摩擦角随着应变速率增大而减小,应变速率大于15%/h时,内摩擦角则随着应变速率增大而增大;黏聚力随着应变速率的增大持续增大。其研究结果对加深融土应变速率效应的理解具有一定的理论意义。

STUDY ON OPTIMIZATION OF HIGH PERFORMANCE CONCRETE ADMIXTURES

Influences of admixtures on the workability and strength of high performance concrete （HPC） are in- vestigated. The types of investigated admixtures include naphthalene series high range water reducing agent, polycarboxlic series high range water reduce agent and sodium sulfate hardening accelerating agent. Two kinds of curing condition, namely steam curing condition and standard curing condition, are adopted. The result shows that HPC, added with polycarboxlic series of high performance water reducer, has high workability and strength, while sodium sulfate accelerating agent causes poor workability and low strength. Thus for vapor-cured HPC and its formulations, naphthalene series high range water reducing agent with less sodium sulfate should be given pri- ority. Therefore, the differences of curing conditions should be considered when selecting HPC admixtures.

Controlled low-strength material incorporating recycled fine aggregate from urban red brick based construction waste

Sixteen controlled low-strength material( CLSM)mixtures with various cement-to-sand( C/Sa) ratios and water-to-solid( W/So) ratios were prepared using recycled fine aggregate from urban red brick based construction waste.The fluidity and bleeding of the fresh CLSM mixtures were measured via the modified test methods, and the hardened CLSM mixtures were then molded to evaluate their compressive strength and durability. The results showthat the fluidity of the fresh CLSM mixtures is 105 to 227 mm with the corresponding bleeding rate of 3. 7% to 15. 5%, which increases with the increase in fluidity. After aging for 28 d,the compressive strength of the hardened CLSM mixtures reaches 1. 15 to 13. 96 M Pa, and their strength can be further enhanced with longer curing ages. Additionally, the strength increases with the increase of the C/Sa ratio, and decreases with the increase of the W/So ratio under the same curing age. Based on the obtained compressive strength, a fitting model for accurately predicting the compressive strength of the CLSM mixtures was established, which takes into account the above two independent variables( C/Sa and W/So ratios).M oreover, the durability of the hardened CLSM mixtures is enhanced for samples with higher C/Sa ratios.

Strength of copolymer grouting material based on orthogonal experiment

Using the orthogonal experimental design method involving three factors and three levels, the flexural strength and the compressive strength of copolymer grouting material were studied with different compositions of water-cement ratio （mass fraction of water to cement）, epoxy resin content, and waterborne epoxy curing agent content. By orthogonal range and variance analysis, the orders of three factors to influence the strength, the significance levels of different factors, and the optimized compound ratio scheme of copolymer grouting material mixture at different curing ages were determined. An empirical relationship among the strength of copolymer grouting material, the water-cement ratio, the epoxy resin content, and the waterborne epoxy curing agent content was established by multivariate regression analysis. The results indicate that water-cement ratio is the most principal and significant influencing factor on the strength. Epoxy resin content and waterbome epoxy curing agent content also have a significant influence on the strength. But epoxy resin content has a greater influence on the 7-day and 28-day flexural strength, and waterborne epoxy curing agent content has a greater influence on the 3-day flexural strength and the compressive strength. The copolymer grouting material with water-cement ratio of 0.4, epoxy resin content of 8% （mass fraction） and waterbome epoxy curing agent content of 2% （mass fraction） is the best one for repairing of cement concrete pavement. The flexural strength and the compressive strength have good correlation, and the ratio of compressive strength to flexural strength is between 1.0 and 3.3.

Water-induced changes in strength characteristics of polyurethane polymer and polypropylene fiber reinforced sand

As a new kind of air-hardening soil reinforcement material,polymer is being widely applied in river-bank slope reinforcement and ecological slope protection area.Thus,more attention should be paid to study the characteristics of reinforced soil after immersion.In this study,water-induced changes in strength characteristics of sand reinforced with polymer and fibers were reported.Several factors,including polymer content(1%,2%,3%and 4%by weight of dry sand),immersion time(6,12,24 and 48 h),dry density(1.40,1.45,1.50,1.55 and 1.60 g/cm^(3),)and fiber content(0.2%,0.4%,0.6%and 0.8%by weight of dry sand)which may influence the strength characteristics of reinforced sand after immersion were analyzed.The microstructure of reinforced sand was analyzed with nuclear magnetic resonance(NMR)and scanning electron microscope(SEM).Experimental results indicate that the compressive strength increases with the increase of polymer content and decreases with the increase of immersion time;the softening coefficients decrease with the increase of the polymer content and immersion time and increase with an increment in density and fiber content.Fiber plays an active role in reducing water-induced loss of strength at 0.6%content.

Strength characteristics of modified polypropylene fiber and cement-reinforced loess

The reinforcement and stabilization of loess soil are duscussed by using fibers as the reinforcement and cement as the stabilization materials.To study the strength characteristics of loess soil reinforced by modified polypropylene(MPP) fiber and cement,samples were prepared with six different fiber contents,three different cement contents,three different curing periods and three kinds of fiber length.The samples were tested under submergence and non-submergence conditions for the unconfined compressive strength(UCS),the splitting tensile strength and the compressive resilient modulus.The results indicated that combined reinforcement by PP fiber and cement could significantly improve the early strength of loess to 3.65–5.99 MPa in three days.With an increase in cement content,the specimens exhibited brittle fracture.However,the addition of fibers gradually modified the mode of fracture from brittle to ductile to plastic.The optimal dosage of fiber to reinforce loess was in the range of 0.3%–0.45% and the optimum fiber length was 12 mm,for which the unconfined compressive strength and tensile strength reached their maxima.Based on the analysis of failure properties,cement-reinforced loess specimens were susceptible to brittle damage under pressure,and the effect of modified polypropylene fiber as the connecting "bridge" could help the specimens achieve a satisfactory level of ductility when under pressure.

Experimental Study on Uniaxial Compressive Strength of Reservoir Ice

Uniaxial compression experiments on horizontal and ervoir were conducted at different temperatures and strain rates vertical samples of first-year freshwater ice in a res- with an electronic universal machine equipped with low temperature cabinet. The results show that there is no difference between the strengths of two horizontal samples with grain sizes ranging from 1 to 4 mm and 4 to 14 mm, while the strength of the 1--4 mm vertical samples is 1.4 times higher than that of the 4--14 mm vertical samples because of the change of crystal structure. For different load- ing directions, the strengths of the horizontal samples do not differ from those of the vertical samples with the same grain sizes. The relation among the uniaxial compressive strength, strain rate and temperature was established through data analysis in both the ductile and brittle regions.

Damage model of fresh concrete in sulphate environment

A model of damage to fresh concrete in a corrosive sulphate environment was formulated to investigate how and why the strength of corroded concrete changes over time. First, a corroded concrete block was divided into three regions: an expanded and dense region; a crack-development region; and a noncorroded region. Second, based on the thickness of the surface corrosion layer and the rate of loss of compressive strength of the corroding region, a computational model of the concrete blocks' corrosion-resistance coefficient of compressive strength in a sulphate environment was generated. Third, experimental tests of the corrosion of concrete were conducted by immersing specimens in a corrosive medium for 270 d. A comparison of the experimental results with the computational formulae shows that the calculation results and test results are in good agreement. A parameter analysis reveals that the corrosion reaction plays a major role in the corrosion of fresh concrete containing ordinary Portland cement,but the diffusion of the corrosion medium plays a major role in the corrosion of concrete mixtures containing fly ash and sulphate-resistant cement. Fresh concrete with a high water-to-cement ratio shows high performance during the whole experiment process whereas fresh concrete with a low water-to-cement ratio shows poor performance during the late experiment period.

Statistical modelling for effect of mix-parameters on properties of high-flowing sand-concrete

The high-flowing sand-concrete （HFSC） containing natural sands as aggregate was carried out. The high fluidity and stability of HFSC can be achieved by tailoring the mix design parameters, such as fine to coarse sand ratio, dosage of additions, water to binder ratio and dosage of admixtures. Mini-cone slump test, v-fl.mnel time test and viscosity model parameters were used to characterize the behaviour of HFSC in fresh state. The mechanical compressive strength in 28 d was also determined. A factorial design approach was used to establish models highlighting the effect of each mix-parameter on measured properties of HFSC. The derived models are valid for mixtures made with 0 to 0.3 of dune sand to total sand ratio, 82 to 418 kg/m3 of marble powder, 0.42 to 0.46 of water/binder ratio and 1.3% to 1.9% of superplasticizer high water-reducer. The results show that the derived models constitute very efficient means for understanding the influence of key mix-parameters on HFSC properties and are useful in selecting the optimum mix proportions, by simulating their impact on fluidity, stability and compressive strength.

Mechanical properties of fiber and cement reinforced heavy metal-contaminated soils as roadbed filling

The treatment of contaminated soil is a crucial issue in geotechnical and environmental engineering.This study proposes to incorporate appropriate polypropylene fibers and cements as an effective method to treat heavy metal contaminated soil(HMCS).The objective of this paper is to investigate the effects of fiber content,fiber length,cement content,curing time,heavy metal types and concentration on the mechanical properties of soils.To this end,a series of direct shear test,unconfined compression strength(UCS)test,dry-wet cycle and freeze-thaw cycle test are performed.The results confirm that the appropriate reinforcement of polypropylene fibers and cement is an effective way to recycle HMCS as substitutable fillers in roadbed,which exhibits benefits in environment and economy development.

Key parameters controlling electrical resistivity and strength of cement treated soils

The improvement of question soils with cement shows great technical, economic and environmental advantages. And interest in introducing electrical resistivity measurement to assess the quality of cement treated soils has increased markedly recently due to its economical, non-destructive, and relatively non-invasive advantages. This work aims to quantify the effect of cement content （aw）, porosity （nt）, and curing time（T） on the electrical resistivity （p） and unconfined compression strength （UCS） of cement treated soil. A series of electrical resistivity tests and UCS tests of cement treated soil specimen after various curing periods were carried out. A modified Archie empirical law was proposed taking into account the effect of cement content and curing period on the electrical resistivity of cement treated soil. The results show that nt/（aw·T） and nt/（aw·T^1/2） ratio are appropriate parameters to assess electrical resistivity and UCS of cement treated soil, respectively. Finally, the relationship between UCS and electrical resistivity was also established.

Study on influence factors of cement-stabilized soil compressive strength

The cement dry jet mixing method has been used to reinforce soft cohesive ground to increase the strength of soft cohesive ground and to decrease its deformation. The study briefly introduces the curing mechanism of cement-soil,presents the factors of influencing on compressive strength,mainly analyses the factors including cement mixing ratio,cement strength grade,curing age,moisture content and soil texture and puts forward some rational proposals at last.

Strengthening pelletization of manganese ore fines containing high combined water by high pressure roll grinding and optimized temperature elevation system

Pelletization is one of useful processes for the agglomeration of iron ore or concentrates. However, manganese ore fines are mainly agglomerated by sintering due to its high combined water which adversely affects the roasting performance of pellets. In this work, high pressure roll grinding(HPRG) process and optimization of temperature elevation system were investigated to improve the strength of fired manganese ore pellets. It is shown that the manganese ore possesses good ballability after being pretreated by HPRG twice, and good green balls were produced under the conditions of blending 2.0% bentonite in the feed, balling for 7 min at 16.00% moisture. High quality roasted pellets with the compressive strength of 2711 N per pellet were manufactured through preheating at 1050 °C for 10 min and firing at 1335 °C for 15 min by controlling the cracks formation. The fired manganese pellets keep the strength by the solid interconnection of recrystallized pyrolusite grains and the binding of manganite liquid phase which filled the pores and clearance among minerals. The product pellets contain high Mn grade and low impurities, and can be used to smelt ferromanganese, which provides a possible way to use imported manganese ore fines containing high combined water to produce high value ferromanganese.

Effects of secondary water curing on the long-term strength and durability of concrete after steam-autoclave curing

To study the effects of secondary water( SW) curing of 20 ℃ for 7 d on concrete long-term strength and durability after steam-autoclave curing, concrete specimens were fabricated and subjected to standard,steam-autoclave or steamautoclave + SW curing. The compressive strength,accelerated carbonation depth, and Coulomb electric charges of the specimens were tested at the ages of 28,90,180,and 360 d.Furthermore,mercury intrusion porosimetry experiments on the specimens were conducted at the age of 180 d. Results indicate that compared with standard curing,steam-autoclave curing can enhance the early-age strength of concrete; however, it is detrimental to the development of later-age strength, and reduces chloride and carbonation resistance. Due to the replenishment of water into concrete,SW curing can refine the micro-pore size and decrease the ratio of harmful and more harmful pores in concrete. As a result,SW curing is effective in improving the long-term strength and durability of steamautoclaved concrete,and makes it approach that under standard curing. The improvement amplitudes of SW curing on the concrete compressive strength, chloride and carbonation resistance at 360 d can reach 20. 3%,48. 6%,and 80. 9%,respectively.

Effect of aggressive pH media on peat treated by cement and sodium silicate grout

The effects of aggressive peat nature (pH) on the strength of peat treated by cement and cement-sodium silicate grout were investigated by evaluating the changes in unconfined compressive strength,moisture content,and scanning electron microscopy (SEM) of samples with time in different pH media.The results indicate that peats treated by cement-silicate have higher strength than peats treated by cement,due to an increase in pH value of the media.Furthermore,cement and cement-silicate are highly effective in reducing the moisture content and void ratio of the treated peats.The microstructures of treated peats support the laboratory test results.

Assessment of strength development in cement-admixed artificial organic soil with GX07

To explore the stabilization effect of stabilizing agent GX07 on treating organic soil and the influence of organic matter on the strength development of stabilized soil,artificial organic soil with various organic matter content was obtained by adding different amounts of fulvic acid into non-organic clay,and then liquid-plastic limit tests were carried out on the artificial organic soil.Meanwhile,unconfined compressive strength(UCS) tests were performed on cement-only soil and composite stabilized soil,respectively.The test results indicate that the plastic limit of soil samples increases linearly,and the liquid limit increases exponentially as the organic matter content increases.The strength of stabilized soil is well correlated with the organic matter content,cement content,stabilizing agent content and curing time.When the organic matter content is 6%,as the cement content varies in the range of 10%-20%,the strength of cement-only soil increases from 88.5 to 280.8 kPa.Once 12.6% GX07 is added into the mix,the strength of stabilized soil is 4.93 times compared with that of cement-only soil.GX07 can obviously improve the strength of cemented-soil and has a good economic applicability.A strength model is proposed to predict strength development.

Size effect on cubic and prismatic compressive strength of cement paste

A series of compression tests were conducted on 150 groups of cement paste specimens with side lengths ranging from 40 mm to 200 mm. The specimens include cube specimens and prism specimens with height to width ratio of 2. The experiment results show that size effect exists in the cubic compressive strength and prismatic compressive strength of the cement paste, and larger specimens resist less in terms of strength than smaller ones. The cubic compressive strength and the prismatic compressive strength of the specimens with side length of 200 mm are respectively about 91% and 89% of the compressive strength of the specimens with the side length of 40 mm. Water to binder ratio has a significant influence on the size effect of the compressive strengths of the cement paste. With a decrease in the water to binder ratio, the size effect is significantly enhanced. When the water to binder ratio is 0.2, the size effects of the cubic compressive strength and the prismatic compressive strength of the cement paste are 1.6 and 1.4 times stronger than those of a water to binder ratio of 0.6. Furthermore, a series of formulas are proposed to calculate the size effect of the cubic compressive strength and the prismatic compressive strength of cement paste, and the results of the size effect predicted by the formulas are in good agreement with the experiment results.

Moisture effect on compressive behavior of concrete under dynamic loading

The effect of moisture content upon compressive mechanical behavior of concrete under impact loading was studied. The axial rapid compressive loading tests of over 50 specimens with five different saturations were executed. The technique "split Hopkinson pressure bar"(SHPB) was used. The impact velocity was 10 m/s with corresponding strain rate of 50 s-1. The compressive behavior of materials was measured in terms of stress-strain curves, dynamic compressive strength, dynamic increase factor(DIF) and critical strain at a maximum stress. The data obtained from test indicate that both ascending and descending portions of stress-stain curves are affected by moisture content. However, the effect is noted to be more significant in ascending portion of the stress-strain curves. Dynamic compressive strength is higher at lower moisture content and weaker at higher moisture content.Furthermore, under nearly saturated condition, an increase in compressive strength can be found. The effect of moisture content on the average DIF of concrete is not significant. The critical compressive strain of concrete does not change with moisture content.