Coal is the backbone of the Indian power sector. The coal-fired power plants remain the largest emitters of carbon dioxide, sulfur dioxide and substantial amounts of nitrogen oxides, which are associated with climate ...Coal is the backbone of the Indian power sector. The coal-fired power plants remain the largest emitters of carbon dioxide, sulfur dioxide and substantial amounts of nitrogen oxides, which are associated with climate and health impacts. Various CO2 mitigation technologies （carbon capture and storage--CCS） and SO2/NOx mitigation technologies （flue gas desulfurization and selective catalytic reduction） have been employed to reduce the environmental impacts of the coal-fired power plants. Therefore, it is imperative to understand the feasibility of various mitigation technologies employed. This paper attempts to perform environmental life cycle assessment （LCA） of Indian coal-fired power plant with and without CO2, SO2 and NOx mitigation controls. The study develops new normalization factors for India in various damage categories, using the Indian emissions and energy consumption data, coupled with the emissions and particulate emission to come up with a final environmental impact of coal-fired electricity. The results show a large degree of dependence on the perspective of assessment used. The impact of sensitivities of individual substances and the effect of plant efficiency on the final LCA results is also studied.展开更多
This paper investigates long-term energy strategy compatible with significant reduction of world carbon dioxide （CO2） emissions, employing a long-term global energy model, Dynamic New Earth 21 （called DNE21）. The ...This paper investigates long-term energy strategy compatible with significant reduction of world carbon dioxide （CO2） emissions, employing a long-term global energy model, Dynamic New Earth 21 （called DNE21）. The model seeks the optimal energy mix from 2000 to 2100 that minimizes the world total energy system cost under various kinds of energy and technological constraints, such as energy resource constraints, energy supply and demand balance constraints, and CO2 emissions constraints. This paper discusses the results of primary energy supply, power generation mix, CO2 emission, CCS （carbon capture and storage） and total system costs for six regions including world as a whole. To evaluate viable pathways forward for implementation of sustainable energy strategies, nuclear power generation is a viable source of clean and green energy to mitigate the CO2 emissions. Present research shows simulation results in two cases consisting of no CO2 regulation case （base case） and CO2 REG case （regulation case） which halves the world CO2 emissions by the year 2050. Main findings of this research describe that renewable and nuclear power generation will contribute significantly to mitigate the CO2 emission worldwide.展开更多
All human activities, including food production, are potentially sources of greenhouse gases （GHG） emissions. In order to provide a better understanding of how to mitigate the GHG emissions, an inventory based on di...All human activities, including food production, are potentially sources of greenhouse gases （GHG） emissions. In order to provide a better understanding of how to mitigate the GHG emissions, an inventory based on different beef supply chains in the United Kingdom and in Brazil was carried out. The carbon footprint of the beef systems was calculated based on the life cycle assessment methodology. Total emissions per kg of bone-free meat were calculated at being 33.85, 33.99 and 45.17 kg of CO2e-100/kg for UK1, UK2 and Brazil farm units, respectively. Based on an average potential for carbon sequestration rate at the proportion of 12：44 for C：CO2 conversion for well managed grasslands, there is a potential sequestration of 1,980 kg of CO2/ha/year. This would potentially reduce the total emissions value for the three distinct supply chains the cases ofUKb UK2 and Brazil, respectively. as being 29.4, 28.4 and 25.4 kg C02-e 100/kg of bone-free meat for展开更多
The HyFrance Group was originally formed in France to support the European project HyWays, by providing （former projects HyFrancel and HyFrance2） the French data and possible hydrogen pathways according to national ...The HyFrance Group was originally formed in France to support the European project HyWays, by providing （former projects HyFrancel and HyFrance2） the French data and possible hydrogen pathways according to national specificities. HyFrance3 is a new project that focuses on the economic competitiveness of different steps of the hydrogen chain, from the production to end usage, at the time horizon of 2030 in France. The project is coordinated by CEA with the other partners being： ADEME （co-funding）, AFH2, CNRS, IFP, Air Liquide, EdF, GdF Suez, TOTAL, ALPHEA. The project is divided into 4 sub-projects, that address present and future French hydrogen industrial markets for chemical ＆ refinery uses, the analysis of the interplay between wind energy production and storage of hydrogen for different automotive requirements （refuelling stations, BtL plants, H2/NG mix）, massive hydrogen storage to balance various offer and demand characteristics, and the supply network （pipeline option competitiveness vs. trucked in supply） to distribute hydrogen in a French region for automotive applications. Technical and economical issues, as well as GHG emissions, are addressed.展开更多
Botswana currently depends on electricity generated from coal-based power plant or electricity supplied from the border in South Africa. The country has good reserves of coal and the solar radiation is sufficiently hi...Botswana currently depends on electricity generated from coal-based power plant or electricity supplied from the border in South Africa. The country has good reserves of coal and the solar radiation is sufficiently high to make solar thermal attractive for generating electricity. The paper presents two conceptual coal-fired power station designs in which a solar sub-system augments heat to the feed heaters or to the boiler. The thermal and economic analyses showed enhanced system performance which indicates that solar power could be embedded into existing fossil fuel plants or new power stations. Integrating solar energy with existing or new fossil fuel based power plants could reduce the cost of stand-alone solar thermal power stations, reduce CO2 emissions and produce experience necessary to operate a full scale solar thermal electricity generation facility.展开更多
Input-output analysis is widely employed to analyze inventories of a product＇s embodied energy and environmental burdens. However, input-output analysis focuses only on the production stage and ignores other life cyc...Input-output analysis is widely employed to analyze inventories of a product＇s embodied energy and environmental burdens. However, input-output analysis focuses only on the production stage and ignores other life cycle phases. Input-output analysis is not exactly a LCA （life cycle assessment） method in the strict sense of ISO 14040 standards, which must cover all stages of a product＇s life cycle, ＂from the cradle to the grave＂, so to speak. A tiered hybrid LCA is a useful tool that covers all life cycle stages by combining a process analysis with the input-output analysis method. This study aims to extend input-output analysis to the use, disposal, and recycling stages by using matrix-based method. The new method is applied to the analysis of the embodied CO2 emissions of a refrigerator as a case study. The entire life cycle C02 emissions are estimated to be 2.9 tons, including indirect emissions, and the reduction in CO2 emissions due to recycling steel scrap is calculated as 48.5 kg. The authors conclude that the new method enables a consistent inventory analysis for all life cycle stages by combining process and input-output methods.展开更多
In the agricultural industry, the importance of transportation costs increases considerably as fuel and labor costs climb. Logistic cooperation is an important strategic alternative to reduce transportation costs and ...In the agricultural industry, the importance of transportation costs increases considerably as fuel and labor costs climb. Logistic cooperation is an important strategic alternative to reduce transportation costs and increase efficiencies. Georgia＇s ornamental industry is characterized by producers that share clients, routes and origins; however, each producer has an independent transportation system. This paper analyses a case study to determine if a transportation alliance, through a horizontal cooperation and routing junction among ornamental producers in Georgia, would reduce shipping costs, increase distribution efficiencies and reduce carbon dioxide emissions. Routing and cost analysis were conducted followed by a sensitivity analysis for each constraint. Results showed that with the use of the GIS ArcLogistics 9.3 software, transportation alliances in the ornamental industry are profitable in terms of transport efficiencies and internal and external costs. Total cost savings per shipping cycle ranged from 1.0% to 13.2%, miles driven savings ranged from 1.1% to 13.6%, total number of trucks required savings ranged from 2.5% to 10% and driving hours savings ranged from 1.0% to 18.4%. CO2 emission reductions were also achieved ranging from 1.2% to 8.4% per shipping cycle.展开更多
In Japan, each municipality generally has its own municipal solid waste incineration facilities because of the principle of self-management in the respective territories. Typically, a small municipality often owns a s...In Japan, each municipality generally has its own municipal solid waste incineration facilities because of the principle of self-management in the respective territories. Typically, a small municipality often owns a small facility. However, a large facility which can run continuously at high temperature with stability would be preferable if the dioxin generation mechanism is to be considered. Accordingly, municipalities in contiguous areas should cooperate mutually by using a large facility. To evaluate the effect of the concentration of large facilities, the authors created a GIS （Geographic Information System） based database of combustible waste generation at town level in Shizuoka Prefecture. Focusing on large facilities in Shizuoka City and superannuated facilities in Shida area, the authors evaluated the effect of the concentration of large facilities in Shizuoka city on utilization rate of facilities, energy balance and CO2 emissions. Our results showed the amount of light oil consumption and CO2 emissions increased because the mileage distance of garbage collection trucks becomes longer. However, the utilization rates of facilities and the amount of energy recovery from waste are improved. From these standpoints, the authors conclude that the concentration of large facilities is better compared to a single municipality based facility.展开更多
The energy and environmental impacts resulting from the buildings sector are one of the impending problems which address the international action. The main strategies implemented to answer to this problem are the ener...The energy and environmental impacts resulting from the buildings sector are one of the impending problems which address the international action. The main strategies implemented to answer to this problem are the energy efficiency improvement, the CO2 emissions reduction and the renewable energy share increase in the energy mix. The key subject discussed in this paper is the ＂building energy impact＂, aimed to leading the building sector towards the energy efficiency improvement. The paper＇s aim is to show that an energy assessment is not able to give a consistent evaluation of building energy use, and it could be misleading. Therefore, the paper proposes the exergy assessment as complementary evaluation method, in order to achieve a complete description of the concept ＂building＇s energy impact on the environment＂. In the first section, we describe the parameters currently used for the building energy assessment, focusing on the primary energy index and the CO2 emissions index. In the second section, we introduce the exergy as a complementary index. This index is a possible answer to the problems previously identified. Finally, in the third section, we present three test-cases, analyzed through transient simulation software TRNSYS. The purpose of the test-cases analysis is to show the difference between energy and exergy assessment.展开更多
VOCs play an increasingly important role in affecting air quality and threatening human health in China in recent years,where industry activities show a significant contribution to VOCs emission.In this article we rep...VOCs play an increasingly important role in affecting air quality and threatening human health in China in recent years,where industry activities show a significant contribution to VOCs emission.In this article we report our long term study of industrial VOCs emissions of six major industries (vehicle manufacturing,printing,equipment coating,electronic manufacturing,furniture manufacturing and bio-pharming) on the aspects of emission characteristics,environmental impact and health risk assessment,and control challenge analysis with the purpose to obtain in-depth understanding of industry VOCs emissions and offer some original basements for national control and management of industry VOCs emissions.This study shows that all these industries give middle or low emission with total VOCs concentration less than 1000 mg/m3 at each exhaust pipe.Benzenes,esters,alcohols,ketones,alkanes,chloroalkanes and alkenes were detected as the major emission components and the most frequently monitored VOCs were benzenes,which varied obviously with different processes and industries.The environmental impact assessments indicate that vehicle manufacturing and benzenes should be prior controlled with the purpose to reduce air pollution.While,health risk assessments suggest that furniture manufacturing and chloroalkanes should be firstly controlled.Control analysis indicates that developing technologies with low cost and high efficiency and establishing and completing specific industry emission standards/regulations are the two key issues in VOCs emission management at present stage.展开更多
文摘Coal is the backbone of the Indian power sector. The coal-fired power plants remain the largest emitters of carbon dioxide, sulfur dioxide and substantial amounts of nitrogen oxides, which are associated with climate and health impacts. Various CO2 mitigation technologies （carbon capture and storage--CCS） and SO2/NOx mitigation technologies （flue gas desulfurization and selective catalytic reduction） have been employed to reduce the environmental impacts of the coal-fired power plants. Therefore, it is imperative to understand the feasibility of various mitigation technologies employed. This paper attempts to perform environmental life cycle assessment （LCA） of Indian coal-fired power plant with and without CO2, SO2 and NOx mitigation controls. The study develops new normalization factors for India in various damage categories, using the Indian emissions and energy consumption data, coupled with the emissions and particulate emission to come up with a final environmental impact of coal-fired electricity. The results show a large degree of dependence on the perspective of assessment used. The impact of sensitivities of individual substances and the effect of plant efficiency on the final LCA results is also studied.
文摘This paper investigates long-term energy strategy compatible with significant reduction of world carbon dioxide （CO2） emissions, employing a long-term global energy model, Dynamic New Earth 21 （called DNE21）. The model seeks the optimal energy mix from 2000 to 2100 that minimizes the world total energy system cost under various kinds of energy and technological constraints, such as energy resource constraints, energy supply and demand balance constraints, and CO2 emissions constraints. This paper discusses the results of primary energy supply, power generation mix, CO2 emission, CCS （carbon capture and storage） and total system costs for six regions including world as a whole. To evaluate viable pathways forward for implementation of sustainable energy strategies, nuclear power generation is a viable source of clean and green energy to mitigate the CO2 emissions. Present research shows simulation results in two cases consisting of no CO2 regulation case （base case） and CO2 REG case （regulation case） which halves the world CO2 emissions by the year 2050. Main findings of this research describe that renewable and nuclear power generation will contribute significantly to mitigate the CO2 emission worldwide.
文摘All human activities, including food production, are potentially sources of greenhouse gases （GHG） emissions. In order to provide a better understanding of how to mitigate the GHG emissions, an inventory based on different beef supply chains in the United Kingdom and in Brazil was carried out. The carbon footprint of the beef systems was calculated based on the life cycle assessment methodology. Total emissions per kg of bone-free meat were calculated at being 33.85, 33.99 and 45.17 kg of CO2e-100/kg for UK1, UK2 and Brazil farm units, respectively. Based on an average potential for carbon sequestration rate at the proportion of 12：44 for C：CO2 conversion for well managed grasslands, there is a potential sequestration of 1,980 kg of CO2/ha/year. This would potentially reduce the total emissions value for the three distinct supply chains the cases ofUKb UK2 and Brazil, respectively. as being 29.4, 28.4 and 25.4 kg C02-e 100/kg of bone-free meat for
文摘The HyFrance Group was originally formed in France to support the European project HyWays, by providing （former projects HyFrancel and HyFrance2） the French data and possible hydrogen pathways according to national specificities. HyFrance3 is a new project that focuses on the economic competitiveness of different steps of the hydrogen chain, from the production to end usage, at the time horizon of 2030 in France. The project is coordinated by CEA with the other partners being： ADEME （co-funding）, AFH2, CNRS, IFP, Air Liquide, EdF, GdF Suez, TOTAL, ALPHEA. The project is divided into 4 sub-projects, that address present and future French hydrogen industrial markets for chemical ＆ refinery uses, the analysis of the interplay between wind energy production and storage of hydrogen for different automotive requirements （refuelling stations, BtL plants, H2/NG mix）, massive hydrogen storage to balance various offer and demand characteristics, and the supply network （pipeline option competitiveness vs. trucked in supply） to distribute hydrogen in a French region for automotive applications. Technical and economical issues, as well as GHG emissions, are addressed.
文摘Botswana currently depends on electricity generated from coal-based power plant or electricity supplied from the border in South Africa. The country has good reserves of coal and the solar radiation is sufficiently high to make solar thermal attractive for generating electricity. The paper presents two conceptual coal-fired power station designs in which a solar sub-system augments heat to the feed heaters or to the boiler. The thermal and economic analyses showed enhanced system performance which indicates that solar power could be embedded into existing fossil fuel plants or new power stations. Integrating solar energy with existing or new fossil fuel based power plants could reduce the cost of stand-alone solar thermal power stations, reduce CO2 emissions and produce experience necessary to operate a full scale solar thermal electricity generation facility.
文摘Input-output analysis is widely employed to analyze inventories of a product＇s embodied energy and environmental burdens. However, input-output analysis focuses only on the production stage and ignores other life cycle phases. Input-output analysis is not exactly a LCA （life cycle assessment） method in the strict sense of ISO 14040 standards, which must cover all stages of a product＇s life cycle, ＂from the cradle to the grave＂, so to speak. A tiered hybrid LCA is a useful tool that covers all life cycle stages by combining a process analysis with the input-output analysis method. This study aims to extend input-output analysis to the use, disposal, and recycling stages by using matrix-based method. The new method is applied to the analysis of the embodied CO2 emissions of a refrigerator as a case study. The entire life cycle C02 emissions are estimated to be 2.9 tons, including indirect emissions, and the reduction in CO2 emissions due to recycling steel scrap is calculated as 48.5 kg. The authors conclude that the new method enables a consistent inventory analysis for all life cycle stages by combining process and input-output methods.
文摘In the agricultural industry, the importance of transportation costs increases considerably as fuel and labor costs climb. Logistic cooperation is an important strategic alternative to reduce transportation costs and increase efficiencies. Georgia＇s ornamental industry is characterized by producers that share clients, routes and origins; however, each producer has an independent transportation system. This paper analyses a case study to determine if a transportation alliance, through a horizontal cooperation and routing junction among ornamental producers in Georgia, would reduce shipping costs, increase distribution efficiencies and reduce carbon dioxide emissions. Routing and cost analysis were conducted followed by a sensitivity analysis for each constraint. Results showed that with the use of the GIS ArcLogistics 9.3 software, transportation alliances in the ornamental industry are profitable in terms of transport efficiencies and internal and external costs. Total cost savings per shipping cycle ranged from 1.0% to 13.2%, miles driven savings ranged from 1.1% to 13.6%, total number of trucks required savings ranged from 2.5% to 10% and driving hours savings ranged from 1.0% to 18.4%. CO2 emission reductions were also achieved ranging from 1.2% to 8.4% per shipping cycle.
文摘In Japan, each municipality generally has its own municipal solid waste incineration facilities because of the principle of self-management in the respective territories. Typically, a small municipality often owns a small facility. However, a large facility which can run continuously at high temperature with stability would be preferable if the dioxin generation mechanism is to be considered. Accordingly, municipalities in contiguous areas should cooperate mutually by using a large facility. To evaluate the effect of the concentration of large facilities, the authors created a GIS （Geographic Information System） based database of combustible waste generation at town level in Shizuoka Prefecture. Focusing on large facilities in Shizuoka City and superannuated facilities in Shida area, the authors evaluated the effect of the concentration of large facilities in Shizuoka city on utilization rate of facilities, energy balance and CO2 emissions. Our results showed the amount of light oil consumption and CO2 emissions increased because the mileage distance of garbage collection trucks becomes longer. However, the utilization rates of facilities and the amount of energy recovery from waste are improved. From these standpoints, the authors conclude that the concentration of large facilities is better compared to a single municipality based facility.
文摘The energy and environmental impacts resulting from the buildings sector are one of the impending problems which address the international action. The main strategies implemented to answer to this problem are the energy efficiency improvement, the CO2 emissions reduction and the renewable energy share increase in the energy mix. The key subject discussed in this paper is the ＂building energy impact＂, aimed to leading the building sector towards the energy efficiency improvement. The paper＇s aim is to show that an energy assessment is not able to give a consistent evaluation of building energy use, and it could be misleading. Therefore, the paper proposes the exergy assessment as complementary evaluation method, in order to achieve a complete description of the concept ＂building＇s energy impact on the environment＂. In the first section, we describe the parameters currently used for the building energy assessment, focusing on the primary energy index and the CO2 emissions index. In the second section, we introduce the exergy as a complementary index. This index is a possible answer to the problems previously identified. Finally, in the third section, we present three test-cases, analyzed through transient simulation software TRNSYS. The purpose of the test-cases analysis is to show the difference between energy and exergy assessment.
基金supported by the Team Interaction and Cooperation of the Science and Technology Program of the Chinese Academy of Sciencesthe Knowledge Innovation Program of the Chinese Academy of Sciences(KZCX2-YW-JS402)+4 种基金the National Basic Research Program of China(2010CB732300)the Strategic Priority Research Program of the Chinese Academy of Science(XDB05050200)the National High Technology Research and Development Program of China(2012AA063101)the Program of Chinese Academy for Environmental Planning(2012A014)Beijing Municipal Natural Science Foundation(8112015)
文摘VOCs play an increasingly important role in affecting air quality and threatening human health in China in recent years,where industry activities show a significant contribution to VOCs emission.In this article we report our long term study of industrial VOCs emissions of six major industries (vehicle manufacturing,printing,equipment coating,electronic manufacturing,furniture manufacturing and bio-pharming) on the aspects of emission characteristics,environmental impact and health risk assessment,and control challenge analysis with the purpose to obtain in-depth understanding of industry VOCs emissions and offer some original basements for national control and management of industry VOCs emissions.This study shows that all these industries give middle or low emission with total VOCs concentration less than 1000 mg/m3 at each exhaust pipe.Benzenes,esters,alcohols,ketones,alkanes,chloroalkanes and alkenes were detected as the major emission components and the most frequently monitored VOCs were benzenes,which varied obviously with different processes and industries.The environmental impact assessments indicate that vehicle manufacturing and benzenes should be prior controlled with the purpose to reduce air pollution.While,health risk assessments suggest that furniture manufacturing and chloroalkanes should be firstly controlled.Control analysis indicates that developing technologies with low cost and high efficiency and establishing and completing specific industry emission standards/regulations are the two key issues in VOCs emission management at present stage.
