This paper focuses on the analysis of running conditions and machining processes of conical cam with oscillating follower. We point out the common errors existing in the design and machining of the widely used plane e...This paper focuses on the analysis of running conditions and machining processes of conical cam with oscillating follower. We point out the common errors existing in the design and machining of the widely used plane expansion method of conical cam trough-out line. We show that the motion can be divided into two parts, i.e. the oscillating motion of oscillating bar and the rotary motion of oscillating bar relative to the conical cam. By increasing the rotary motion of oscillating bar, the motion path of tapered roller on oscillating bar (i.e. contour surface of conical cam) can be expanded on the cylinder. Based on these analyses, we present a creative and effective designing and machining method for 3D curve expansion of conical cam with oscillating follower.展开更多
By using an instrumented impact pendulum, the force versus time curves of 7075-T651 aluminum welds were obtained from standard Charpy-V samples. Considering the force-time curves and constant impact velocity, the frac...By using an instrumented impact pendulum, the force versus time curves of 7075-T651 aluminum welds were obtained from standard Charpy-V samples. Considering the force-time curves and constant impact velocity, the fracture energies for different zones were quantified. A fracture energy improvement for the HAZ(33.6 J) was observed in comparison with the weld metal(7.88 J), and base metal(5.37 J and 7.37 J for longitudinal and transverse directions, respectively). This toughness increment was attributed to the microstructural transformation caused by the thermodynamic instability of η′ precipitates during the welding. Fracture energy for weld metal was higher than that for base metal, probably due to pores created during solidification. Regarding the dynamic yielding force obtained from the force-time curves, an approximation to the dynamic yield strength for weld, HAZ and base metal was determined. Fracture surfaces revealed an intergranular failure for base metal in longitudinal direction, whereas a predominately brittle failure(cleavage) with some insights of ductile characteristics was observed for the transverse direction. In contrast, a ductile failure was observed for weld metal and HAZ.展开更多
基金Project supported by the National Natural Science Foundation of China (No. 50575205)the HiTech Research and Development Program (863) of China (No. 2006AA04Z233)and the Natural Science Foundation of Zhejiang Province (Nos. Y104243 and Y105686), China
文摘This paper focuses on the analysis of running conditions and machining processes of conical cam with oscillating follower. We point out the common errors existing in the design and machining of the widely used plane expansion method of conical cam trough-out line. We show that the motion can be divided into two parts, i.e. the oscillating motion of oscillating bar and the rotary motion of oscillating bar relative to the conical cam. By increasing the rotary motion of oscillating bar, the motion path of tapered roller on oscillating bar (i.e. contour surface of conical cam) can be expanded on the cylinder. Based on these analyses, we present a creative and effective designing and machining method for 3D curve expansion of conical cam with oscillating follower.
基金CONACy T (project CB 177834)SIP-IPN for the funds given to conduct this research
文摘By using an instrumented impact pendulum, the force versus time curves of 7075-T651 aluminum welds were obtained from standard Charpy-V samples. Considering the force-time curves and constant impact velocity, the fracture energies for different zones were quantified. A fracture energy improvement for the HAZ(33.6 J) was observed in comparison with the weld metal(7.88 J), and base metal(5.37 J and 7.37 J for longitudinal and transverse directions, respectively). This toughness increment was attributed to the microstructural transformation caused by the thermodynamic instability of η′ precipitates during the welding. Fracture energy for weld metal was higher than that for base metal, probably due to pores created during solidification. Regarding the dynamic yielding force obtained from the force-time curves, an approximation to the dynamic yield strength for weld, HAZ and base metal was determined. Fracture surfaces revealed an intergranular failure for base metal in longitudinal direction, whereas a predominately brittle failure(cleavage) with some insights of ductile characteristics was observed for the transverse direction. In contrast, a ductile failure was observed for weld metal and HAZ.
