A new experimental apparatus was set up to investigate the actual fi-iction characteristics on the basis of speed control of the serve system.A modified friction model was proposed due to real time varying deformation...A new experimental apparatus was set up to investigate the actual fi-iction characteristics on the basis of speed control of the serve system.A modified friction model was proposed due to real time varying deformation resistance.The approach to identify the parameters of comprehensive friction behaviors based on the modified model was proposed and applied to the forging press.The impacts on parameters which the external load had were also investigated.The results show that friction force decreases with velocity in the low velocity regime whereas the friction force increases with the velocity in the high velocity regime under no external load.It is also shown that the Coulomb friction force,the maximum static friction force and the vicious friction coefficient change linearly with the external load taking the velocity at which the magnitude of the steady state friction force becomes minimum as the critical velocity.展开更多
Recently,hybrid energy harvester has been considered as an attractive potential approach to response the worldwide energy crisis due to the combination of advantages from different harvesting mechanism.In this paper,a...Recently,hybrid energy harvester has been considered as an attractive potential approach to response the worldwide energy crisis due to the combination of advantages from different harvesting mechanism.In this paper,a novel low-frequency wide-band hybrid energy harvester based on piezoelectric and triboelectric mechanism is presented and systematically studied including structural design,fabrication process,working principle simulation and measurement.With a vibrational excitation,the polyvinylidene fluoride(PVDF) cantilevers will vibrate and impact the polydimethylsiloxane(PDMS) film on the substrate,producing a piezoelectric output as well as a triboelectric output.The structural parameters of each cantilever are optimized using finite element simulation,and the well-designed PVDF cantilevers with controllable PDMS mass not only reduce the device working frequency but also enlarge the bandwidth.Under a sweep-frequency test,three voltage peaks induced by the piezoelectric part are observed at 15,32.5 and 47.5 Hz,with the value of 320,288 and 264 mV,respectively.With the combined triboelectric part,a 20 V peak-peak voltage is generated at 15 Hz.The electrical driving ability of this hybrid energy harvester also has been demonstrated by lighting up a commercial light emitting diode(LED).展开更多
基金Project(51005251)supported by the National Natural Science Foundation of ChinaProject(2011CB706802)supported by the National Basic Research Development Program of China(973 Program)
文摘A new experimental apparatus was set up to investigate the actual fi-iction characteristics on the basis of speed control of the serve system.A modified friction model was proposed due to real time varying deformation resistance.The approach to identify the parameters of comprehensive friction behaviors based on the modified model was proposed and applied to the forging press.The impacts on parameters which the external load had were also investigated.The results show that friction force decreases with velocity in the low velocity regime whereas the friction force increases with the velocity in the high velocity regime under no external load.It is also shown that the Coulomb friction force,the maximum static friction force and the vicious friction coefficient change linearly with the external load taking the velocity at which the magnitude of the steady state friction force becomes minimum as the critical velocity.
基金supported by the National Natural Science Foundation of China (Grant Nos. 61176103,91023045)the National HiTech Research and Development Program of China ("863" Project) (Grant No.2013AA041102)+1 种基金the National Ph. D. Foundation Project (Grant No.20110001110103)the Global Research Outreach Program of Samsung Advanced Institute of Technology
文摘Recently,hybrid energy harvester has been considered as an attractive potential approach to response the worldwide energy crisis due to the combination of advantages from different harvesting mechanism.In this paper,a novel low-frequency wide-band hybrid energy harvester based on piezoelectric and triboelectric mechanism is presented and systematically studied including structural design,fabrication process,working principle simulation and measurement.With a vibrational excitation,the polyvinylidene fluoride(PVDF) cantilevers will vibrate and impact the polydimethylsiloxane(PDMS) film on the substrate,producing a piezoelectric output as well as a triboelectric output.The structural parameters of each cantilever are optimized using finite element simulation,and the well-designed PVDF cantilevers with controllable PDMS mass not only reduce the device working frequency but also enlarge the bandwidth.Under a sweep-frequency test,three voltage peaks induced by the piezoelectric part are observed at 15,32.5 and 47.5 Hz,with the value of 320,288 and 264 mV,respectively.With the combined triboelectric part,a 20 V peak-peak voltage is generated at 15 Hz.The electrical driving ability of this hybrid energy harvester also has been demonstrated by lighting up a commercial light emitting diode(LED).
