An important consideration when using hot-dip galvanized tubular structures is the uncertainty of the joint behaviour due to the possible reduction in the global joint resistance produced by the vent holes required fo...An important consideration when using hot-dip galvanized tubular structures is the uncertainty of the joint behaviour due to the possible reduction in the global joint resistance produced by the vent holes required for the galvanizing process. This paper assesses the effect on the joint strength of the angle between the brace members and the chord in a K- or N-joints made with rectangular hollow sections. The study is focused on the case when those brace members include characteristic holes required for the hot-dip galvanizing process. To accomplish the objective of the proposed work, some tests on full-scale K- and N-joints, including angles of 35°, 45°, 55° and 90°, were carried out. The experimental work was complemented by a validated numerical simulation in order to give some design recommendations and to extend the research to other joint configurations.展开更多
A series of ethylene oxide (EO)-propylene oxide (PO) randomco-polymers (EOPO) were used to form aqueous two-phase systems (ATPS)with ammonium sulfate. Effects of EOPO's properties on the phaseseparation behaviors ...A series of ethylene oxide (EO)-propylene oxide (PO) randomco-polymers (EOPO) were used to form aqueous two-phase systems (ATPS)with ammonium sulfate. Effects of EOPO's properties on the phaseseparation behaviors and on the partition of cephalexin and7-aminodesacetoxicephalosporanic acid (7-ADCA) in ATPS wereinvestigated. Both the molar mass and molar ratio of EO to PO of EOPOcould greatly influence partition behaviors of cephalexin and 7-ADCAas well as the binodal curve of ATPS.展开更多
In order to investigate the effects of probe support on the stall characteristics of micro compressors, an experiment was carried out on a large-scale low-speed research compressor according to the principle of geomet...In order to investigate the effects of probe support on the stall characteristics of micro compressors, an experiment was carried out on a large-scale low-speed research compressor according to the principle of geometric similarity. A cylindrical probe support intruding to 50% blade span was mounted at 50% chord upstream from the rotor blade leading edge. The static pressure rise characteristic of the compressor is measured, with and without the probe support respectively. The dynamic compressor behavior from pre-stall to full stall was also measured. The results indicate that the stability margin of the compressor is lowered after installing the probe support. The stall inception is aroused by modal wave disturbances. The disturbances developed into two stall cells smoothly before installing the probe support, while the disturbances first developed into a single stall cell then splitting into two stall cells after installing the probe support. The presence of probe support lowers the initial intensity of the rotating stall of the compressor, while it doesn't alter the intensity of the rotation stall after the compressor enters into full stall.展开更多
文摘An important consideration when using hot-dip galvanized tubular structures is the uncertainty of the joint behaviour due to the possible reduction in the global joint resistance produced by the vent holes required for the galvanizing process. This paper assesses the effect on the joint strength of the angle between the brace members and the chord in a K- or N-joints made with rectangular hollow sections. The study is focused on the case when those brace members include characteristic holes required for the hot-dip galvanizing process. To accomplish the objective of the proposed work, some tests on full-scale K- and N-joints, including angles of 35°, 45°, 55° and 90°, were carried out. The experimental work was complemented by a validated numerical simulation in order to give some design recommendations and to extend the research to other joint configurations.
基金Supported by the National Natural Science Foundation of China (No. 29873014) and the Key Disciplinary Foundation of Shanghai.
文摘A series of ethylene oxide (EO)-propylene oxide (PO) randomco-polymers (EOPO) were used to form aqueous two-phase systems (ATPS)with ammonium sulfate. Effects of EOPO's properties on the phaseseparation behaviors and on the partition of cephalexin and7-aminodesacetoxicephalosporanic acid (7-ADCA) in ATPS wereinvestigated. Both the molar mass and molar ratio of EO to PO of EOPOcould greatly influence partition behaviors of cephalexin and 7-ADCAas well as the binodal curve of ATPS.
基金funded by the National Natural Science Foundation of China(Grant No.51161130525 and 51136003)the 111 Project,No.B07009
文摘In order to investigate the effects of probe support on the stall characteristics of micro compressors, an experiment was carried out on a large-scale low-speed research compressor according to the principle of geometric similarity. A cylindrical probe support intruding to 50% blade span was mounted at 50% chord upstream from the rotor blade leading edge. The static pressure rise characteristic of the compressor is measured, with and without the probe support respectively. The dynamic compressor behavior from pre-stall to full stall was also measured. The results indicate that the stability margin of the compressor is lowered after installing the probe support. The stall inception is aroused by modal wave disturbances. The disturbances developed into two stall cells smoothly before installing the probe support, while the disturbances first developed into a single stall cell then splitting into two stall cells after installing the probe support. The presence of probe support lowers the initial intensity of the rotating stall of the compressor, while it doesn't alter the intensity of the rotation stall after the compressor enters into full stall.
