The effect of homogenization time on quench sensitivity of a cast 7085 aluminum alloy was investigated by means of end-quenching test, optical microscope （OM）, scanning electron microscope （SEM） and transmission e...The effect of homogenization time on quench sensitivity of a cast 7085 aluminum alloy was investigated by means of end-quenching test, optical microscope （OM）, scanning electron microscope （SEM） and transmission electron microscope （TEM）. The results show that with the increase of homogenization time from 48 h to 384 h, quench sensitivity increased slightly as the largest difference in the hardness was increased from 5.2% to 6.9% in the end-quenched and aged specimens. Prolonging homogenization had little effect on the grain structure, but improved the dissolution of soluble T phase and resulted in larger Al3Zr dispersoids with a low number density. Some small quench-induced η phase particles on Al3Zr dispersoids were observed inside grains during slow quenching, which decreased hardness after subsequent aging. The change in the character of Al3Zr dispersoids exerted slight influence on quench sensitivity.展开更多
A discrete time stochastic traffic assignment model is proposed. The model provides a discrete time description of the variations of flows on a road network during a day or a peak period. The congestion effect at li...A discrete time stochastic traffic assignment model is proposed. The model provides a discrete time description of the variations of flows on a road network during a day or a peak period. The congestion effect at links and link junctions are taken into account. The first in first out principle is enforced on all links at all periods of the day. A stochastic user equilibrium assignment is achieved when the tripmaker is unable to find better travel alternatives. A computational procedure is also presented.展开更多
Through alloy sampling combined with diffusion triple technique, phase equilibria in Al-Ti-Zr ternary system at 1073 Kwere experimentally determined with electron probe microanalysis （EPMA）. Experimental results sho...Through alloy sampling combined with diffusion triple technique, phase equilibria in Al-Ti-Zr ternary system at 1073 Kwere experimentally determined with electron probe microanalysis （EPMA）. Experimental results show that there is a solid solutionβ（Ti,Zr） which dissolves Al up to 16.3% （mole fraction）. Ti and Zr can substitute each other in most Ti-Al and Al-Zr binaryintermediate phases to a certain degree while the maximum solubility of Zr in Ti3Al and TiAl reaches up to 17.9% and 4.0% （molefraction）, respectively. The isothermal section consists of 16 single-phased regions, 27 two-phased regions and 14 three-phasedregions. No ternary phase was detected.展开更多
The Intalox metal tower packing was used to simulate an industrial relevant extractive distillation column for purifying azeotropic multicomponent mixture.In order to explain the inconsistencies in the modeling of tra...The Intalox metal tower packing was used to simulate an industrial relevant extractive distillation column for purifying azeotropic multicomponent mixture.In order to explain the inconsistencies in the modeling of transfer process in nonideal multicomponent distillation column,a method was developed with equilibrium stage models(EQ)and non-equilibrium model(NEQ)incorporated with Maxwell-Stefan diffusion equations in the framework of AspenONE simulator.Dortmund Modified UNIFAC(UNIFAC-DMD)thermodynamic model was employed to estimate activity coefficients.In addition,to understand the reason for the diffusion against driving force and the different results by EQ and NEQ models,explicit investigations were made on diffusion coefficients, component Murphree efficiency and mass transfer coefficients.The results provide valuable information for basic design and applications associated with extractive distillation.展开更多
Phase equilibria in Ti?Ni?Pt ternary system have been experimentally determined through diffusion triple technique combined with alloy samples approach.Assisted with electron probe microanalysis(EPMA)and X-ray diffrac...Phase equilibria in Ti?Ni?Pt ternary system have been experimentally determined through diffusion triple technique combined with alloy samples approach.Assisted with electron probe microanalysis(EPMA)and X-ray diffraction(XRD)techniques,isothermal sections at 1073 and 1173 K of this system were constructed and existence of ternary phase Ti2(Ni,Pt)3 was confirmed.In addition,binary compounds Ti3Pt5 and TiPt3-were found to be stable at 1073 and 1173 K,and remarkable ternary solubility in some binary compounds was detected,e.g.,solubility of Pt in TiNi can be up to about 36%(molar fraction)at 1073 K and 40%(molar fraction)at 1173 K.Furthermore,a ternary invariant transition reaction TiNi3+Ti3Pt5→Ti2(Ni,Pt)3+TiPt3+at a temperature between 1073 and 1173 K was deduced.展开更多
Updated version of local non-equilibrium diffusion model （LNDM） for rapid solidification of binary alloys was considered. The LNDM takes into account deviation from local equilibrium of solute concentration and solu...Updated version of local non-equilibrium diffusion model （LNDM） for rapid solidification of binary alloys was considered. The LNDM takes into account deviation from local equilibrium of solute concentration and solute flux fields in bulk liquid. The exact solutions for solute concentration and flux in bulk liquid were obtained using hyperbolic diffusion equations. The results show the transition from diffusion-limited to purely thermally controlled solidification with effective diffusion coefficient →0 and complete solute trapping KLNDM（v）→1 at v→vDb for any kind of solid-liquid interface kinetics. Critical parameter for diffusionless solidification and complete solute trapping is the diffusion speed in bulk liquid vDb. Different models for solute trapping at the interface with different interface kinetic approaches were considered.展开更多
The discrete element method (DEM) was used to simulate the flow characteristic and strength characteristic of the conditioned sands in the earth pressure balance (EPB) tunneling. In the laboratory the conditioned sand...The discrete element method (DEM) was used to simulate the flow characteristic and strength characteristic of the conditioned sands in the earth pressure balance (EPB) tunneling. In the laboratory the conditioned sands were reproduced and the slump test and the direct shear test of the conditioned sands were implemented. A DEM equivalent model that can simulate the macro mechanical characteristic of the conditioned sands was proposed,and the corresponding numerical models of the slump test and the shear test were established. By selecting proper DEM model parameters,the errors of the slump values between the simulation results and the test results are in the range of 10.3%-14.3%,and the error of the curves between the shear displacement and the shear stress calculated with the DEM simulation is 4.68%-16.5% compared with that of the laboratory direct shear test. This illustrates that the proposed DEM equivalent model can approximately simulate the mechanical characteristics of the conditioned sands,which provides the basis for further simulation of the interaction between the conditioned soil and the chamber pressure system of the EPB machine.展开更多
On the basis of population balance a mathematical model is developed to describe the formation of polymer particle in styrene suspension polymerization. The characteristics of coalescence and breakage of droplets and ...On the basis of population balance a mathematical model is developed to describe the formation of polymer particle in styrene suspension polymerization. The characteristics of coalescence and breakage of droplets and the gel effect are analyzed in particular. Parameters of the models are estimated by experimental data on reaction conversion and particle size distribution. The results show that the model is suitable for predicting polymerization processes.展开更多
In terms of numerical method of Smoluchowski equation the behavior of fission process in diffusion model has been described and analyzed, including the reliance upon time, as well as the deformation parameters at seve...In terms of numerical method of Smoluchowski equation the behavior of fission process in diffusion model has been described and analyzed, including the reliance upon time, as well as the deformation parameters at several nuclear temperatures in this paper. The fission rates and the residual probabilities inside the saddle point are calculated for fissile nucleus n＋^238U reaction and un-fissile nucleus p＋^208Pb reaction. The results indicate that there really exists a transient fission process, which means that the pre-equillbrium fission should be taken into account for the fissile nucleus at the high temperature. Oppositely, the pre-equilibrlum fission could be neglected for the un-fissile nucleus. In the certain case the overshooting phenomenon of the fission rates will occur, which is mainly determined by the diffusive current at the saddle point. The higher the temperature is, the more obvious the overshooting phenomenon is. However, the emissions of the light particles accompanying the diffusion process may weaken or vanish the overshooting phenomenon.展开更多
基金Project(2012CB619500)supported by the National Basic Research Program of ChinaProject supported by Yuying Project of Central South University
文摘The effect of homogenization time on quench sensitivity of a cast 7085 aluminum alloy was investigated by means of end-quenching test, optical microscope （OM）, scanning electron microscope （SEM） and transmission electron microscope （TEM）. The results show that with the increase of homogenization time from 48 h to 384 h, quench sensitivity increased slightly as the largest difference in the hardness was increased from 5.2% to 6.9% in the end-quenched and aged specimens. Prolonging homogenization had little effect on the grain structure, but improved the dissolution of soluble T phase and resulted in larger Al3Zr dispersoids with a low number density. Some small quench-induced η phase particles on Al3Zr dispersoids were observed inside grains during slow quenching, which decreased hardness after subsequent aging. The change in the character of Al3Zr dispersoids exerted slight influence on quench sensitivity.
文摘A discrete time stochastic traffic assignment model is proposed. The model provides a discrete time description of the variations of flows on a road network during a day or a peak period. The congestion effect at links and link junctions are taken into account. The first in first out principle is enforced on all links at all periods of the day. A stochastic user equilibrium assignment is achieved when the tripmaker is unable to find better travel alternatives. A computational procedure is also presented.
基金Project(51171210)supported by the National Natural Science Foundation of ChinaProject(2014CB6644002)supported by the Major State Basic Research Development Program of China
文摘Through alloy sampling combined with diffusion triple technique, phase equilibria in Al-Ti-Zr ternary system at 1073 Kwere experimentally determined with electron probe microanalysis （EPMA）. Experimental results show that there is a solid solutionβ（Ti,Zr） which dissolves Al up to 16.3% （mole fraction）. Ti and Zr can substitute each other in most Ti-Al and Al-Zr binaryintermediate phases to a certain degree while the maximum solubility of Zr in Ti3Al and TiAl reaches up to 17.9% and 4.0% （molefraction）, respectively. The isothermal section consists of 16 single-phased regions, 27 two-phased regions and 14 three-phasedregions. No ternary phase was detected.
基金Supported by the National Natural Science Foundation of China （20776118）, Science ＆ Technology Bureau of Xi＇an [CXY09019 （1）], Innovation Foundation for Graduated Student of Northwest University （08YJC21）, Shaanxi Research Center of Engineering Technology for Clean Coal Conversion （2008ZDGC-13）.
文摘The Intalox metal tower packing was used to simulate an industrial relevant extractive distillation column for purifying azeotropic multicomponent mixture.In order to explain the inconsistencies in the modeling of transfer process in nonideal multicomponent distillation column,a method was developed with equilibrium stage models(EQ)and non-equilibrium model(NEQ)incorporated with Maxwell-Stefan diffusion equations in the framework of AspenONE simulator.Dortmund Modified UNIFAC(UNIFAC-DMD)thermodynamic model was employed to estimate activity coefficients.In addition,to understand the reason for the diffusion against driving force and the different results by EQ and NEQ models,explicit investigations were made on diffusion coefficients, component Murphree efficiency and mass transfer coefficients.The results provide valuable information for basic design and applications associated with extractive distillation.
基金Project(2016YFB0701404)supported by the National Key Research and Development Program of ChinaProject(51171210)supported by the National Natural Science Foundation of China
文摘Phase equilibria in Ti?Ni?Pt ternary system have been experimentally determined through diffusion triple technique combined with alloy samples approach.Assisted with electron probe microanalysis(EPMA)and X-ray diffraction(XRD)techniques,isothermal sections at 1073 and 1173 K of this system were constructed and existence of ternary phase Ti2(Ni,Pt)3 was confirmed.In addition,binary compounds Ti3Pt5 and TiPt3-were found to be stable at 1073 and 1173 K,and remarkable ternary solubility in some binary compounds was detected,e.g.,solubility of Pt in TiNi can be up to about 36%(molar fraction)at 1073 K and 40%(molar fraction)at 1173 K.Furthermore,a ternary invariant transition reaction TiNi3+Ti3Pt5→Ti2(Ni,Pt)3+TiPt3+at a temperature between 1073 and 1173 K was deduced.
文摘Updated version of local non-equilibrium diffusion model （LNDM） for rapid solidification of binary alloys was considered. The LNDM takes into account deviation from local equilibrium of solute concentration and solute flux fields in bulk liquid. The exact solutions for solute concentration and flux in bulk liquid were obtained using hyperbolic diffusion equations. The results show the transition from diffusion-limited to purely thermally controlled solidification with effective diffusion coefficient →0 and complete solute trapping KLNDM（v）→1 at v→vDb for any kind of solid-liquid interface kinetics. Critical parameter for diffusionless solidification and complete solute trapping is the diffusion speed in bulk liquid vDb. Different models for solute trapping at the interface with different interface kinetic approaches were considered.
基金Project (2007CB714006) supported by the National Basic Research Program of China
文摘The discrete element method (DEM) was used to simulate the flow characteristic and strength characteristic of the conditioned sands in the earth pressure balance (EPB) tunneling. In the laboratory the conditioned sands were reproduced and the slump test and the direct shear test of the conditioned sands were implemented. A DEM equivalent model that can simulate the macro mechanical characteristic of the conditioned sands was proposed,and the corresponding numerical models of the slump test and the shear test were established. By selecting proper DEM model parameters,the errors of the slump values between the simulation results and the test results are in the range of 10.3%-14.3%,and the error of the curves between the shear displacement and the shear stress calculated with the DEM simulation is 4.68%-16.5% compared with that of the laboratory direct shear test. This illustrates that the proposed DEM equivalent model can approximately simulate the mechanical characteristics of the conditioned sands,which provides the basis for further simulation of the interaction between the conditioned soil and the chamber pressure system of the EPB machine.
文摘On the basis of population balance a mathematical model is developed to describe the formation of polymer particle in styrene suspension polymerization. The characteristics of coalescence and breakage of droplets and the gel effect are analyzed in particular. Parameters of the models are estimated by experimental data on reaction conversion and particle size distribution. The results show that the model is suitable for predicting polymerization processes.
基金The project supported by National Natural Science Foundation of China under Grant No. 10547005
文摘In terms of numerical method of Smoluchowski equation the behavior of fission process in diffusion model has been described and analyzed, including the reliance upon time, as well as the deformation parameters at several nuclear temperatures in this paper. The fission rates and the residual probabilities inside the saddle point are calculated for fissile nucleus n＋^238U reaction and un-fissile nucleus p＋^208Pb reaction. The results indicate that there really exists a transient fission process, which means that the pre-equillbrium fission should be taken into account for the fissile nucleus at the high temperature. Oppositely, the pre-equilibrlum fission could be neglected for the un-fissile nucleus. In the certain case the overshooting phenomenon of the fission rates will occur, which is mainly determined by the diffusive current at the saddle point. The higher the temperature is, the more obvious the overshooting phenomenon is. However, the emissions of the light particles accompanying the diffusion process may weaken or vanish the overshooting phenomenon.
