Multistage centrifugal impellers with four different skew angles were investigated by using computational fluid dynamics.The purpose of this work is to investigate the influences of lean angle at the blade tip of the ...Multistage centrifugal impellers with four different skew angles were investigated by using computational fluid dynamics.The purpose of this work is to investigate the influences of lean angle at the blade tip of the impeller inlet.Four variations of lean angles,that is,8°,10°,15° and 20°,were made at first stage impeller.Reynolds Average Navier Stokes equation was used in simulation together with a shear?stress transport(SST) k-w turbulence model and mixing-plane approach,respectively.Three dimensional fluid flows were simplified using periodic model to reduce the computational cost and time required.A good performance was expected that the secondary flow can be effectively reduced in the flow passage of the impeller without excessive increase in manufacturing cost caused by the secondary flow.The results show that secondary flow affects the main flow intricately to form vortices or having non-uniform velocity in the flow passage,which in turn results in substantial fluid energy loss not only in the impeller but also in the guide vane downstream of impeller.The numerical solutions were performed and allowed the optimum design and operating conditions to be obtained.展开更多
The performance of inclined pile group embedded in consolidating soil under surcharge load was investigated by experiment in comparison with vertical pile group and single pile under the same conditions; dragload, dow...The performance of inclined pile group embedded in consolidating soil under surcharge load was investigated by experiment in comparison with vertical pile group and single pile under the same conditions; dragload, downdrag, and layered soil settlement were measured. A three-dimensional numerical model was built via FLAC3D software, and verified by the experimental results. Influence factors, such as consolidation time, pile spacing, and pile tilt angle were analyzed. The results show that dragload of inclined pile group increases with the increase of consolidation time and pile spacing or the decrease of pile tilt angle. Downdrag of inclined pile group increases with the increase of consolidation time, pile spacing and pile tilt angle.展开更多
When applying fiat belts, correct tracking of the belt through the installation has to be assured. Since flat belts are commonly used for conveying and transmission purposes, tracking systems have been well developed,...When applying fiat belts, correct tracking of the belt through the installation has to be assured. Since flat belts are commonly used for conveying and transmission purposes, tracking systems have been well developed, but the ultimate tracking behaviour of the belt can be greatly enhanced by taking special care in the creation of an adequate tracking mechanism. To obtain long-life operation and full value from the equipment, the correct tracking technique plays an important role. This paper deals with two tracking techniques： The skewed and the angled pulley axis. Numerical simulation results are compared with both measurements and an analytical approach. The advantages of numerical simulation compared to experimental tests are ease, convenience and the absence of any safety risk. Compared to analytical approaches the simulation is used for systems for which simple closed form analytic solutions are not possible.展开更多
基金Project(NRF-2010-013-D00007) supported by the National Research Foundation of KoreaWork finacially supported by the 2010 Research Professor Fund of Gyeongsang National University,Korea
文摘Multistage centrifugal impellers with four different skew angles were investigated by using computational fluid dynamics.The purpose of this work is to investigate the influences of lean angle at the blade tip of the impeller inlet.Four variations of lean angles,that is,8°,10°,15° and 20°,were made at first stage impeller.Reynolds Average Navier Stokes equation was used in simulation together with a shear?stress transport(SST) k-w turbulence model and mixing-plane approach,respectively.Three dimensional fluid flows were simplified using periodic model to reduce the computational cost and time required.A good performance was expected that the secondary flow can be effectively reduced in the flow passage of the impeller without excessive increase in manufacturing cost caused by the secondary flow.The results show that secondary flow affects the main flow intricately to form vortices or having non-uniform velocity in the flow passage,which in turn results in substantial fluid energy loss not only in the impeller but also in the guide vane downstream of impeller.The numerical solutions were performed and allowed the optimum design and operating conditions to be obtained.
基金Supported by National Natural Science Foundation of China (No. 51008116)State Key Laboratory of Coastal and Offshore Engineering (No. LP1014)+1 种基金Fundamental Research Funds for the Central Universities (No. 2009B14514)China Postdoctoral Science Foundation (No. 20090461062)
文摘The performance of inclined pile group embedded in consolidating soil under surcharge load was investigated by experiment in comparison with vertical pile group and single pile under the same conditions; dragload, downdrag, and layered soil settlement were measured. A three-dimensional numerical model was built via FLAC3D software, and verified by the experimental results. Influence factors, such as consolidation time, pile spacing, and pile tilt angle were analyzed. The results show that dragload of inclined pile group increases with the increase of consolidation time and pile spacing or the decrease of pile tilt angle. Downdrag of inclined pile group increases with the increase of consolidation time, pile spacing and pile tilt angle.
文摘When applying fiat belts, correct tracking of the belt through the installation has to be assured. Since flat belts are commonly used for conveying and transmission purposes, tracking systems have been well developed, but the ultimate tracking behaviour of the belt can be greatly enhanced by taking special care in the creation of an adequate tracking mechanism. To obtain long-life operation and full value from the equipment, the correct tracking technique plays an important role. This paper deals with two tracking techniques： The skewed and the angled pulley axis. Numerical simulation results are compared with both measurements and an analytical approach. The advantages of numerical simulation compared to experimental tests are ease, convenience and the absence of any safety risk. Compared to analytical approaches the simulation is used for systems for which simple closed form analytic solutions are not possible.
