According to the winter temperature of Peking,the freeze-thaw（FT） condition in laboratory was determined.Seven groups of epoxy asphalt concrete（EAC） specimen were exposed to different FT cycles.The flexural modulu...According to the winter temperature of Peking,the freeze-thaw（FT） condition in laboratory was determined.Seven groups of epoxy asphalt concrete（EAC） specimen were exposed to different FT cycles.The flexural modulus and fracture energy（G_F） of EAC exposed to different FT cycles were obtained through the 3-point bending test.Meanwhile,the plane strain fracture toughness（K_（IC）） of EAC was obtained through numerical simulation.The results show that the flexural modulus of the FT conditioned EAC samples decreases with the increase of FT cycles.The FT damage of flexural modulus is 60%after 30 FT cycles.Nevertheless,with the increase of FT cycles,the G_F and K_（IC） of EAC decrease first and then increase after 15 FT cycles.展开更多
作为生产复合材料板的一种可供选择的原材料,竹材获得越来越多的关注。用Betung竹材(Dendrocalamus Asper(Schultes.F)Backer Ex Heyne,马来甜龙竹)制得的三层OSB来评估刨片结构长度和预处理技术对其物理力学性能,以及耐久性方面的影响...作为生产复合材料板的一种可供选择的原材料,竹材获得越来越多的关注。用Betung竹材(Dendrocalamus Asper(Schultes.F)Backer Ex Heyne,马来甜龙竹)制得的三层OSB来评估刨片结构长度和预处理技术对其物理力学性能,以及耐久性方面的影响。结果显示,在垂直于纹理方向上,刨片长度对于其断裂模量(MOR)和弹性模量(MOE)的影响很大。将刨片放入乙酸酐溶液中浸泡对于提高OSB尺寸的稳定性略有改善。在实验条件中,将板材浸入冷水和乙酸酐溶液提高了OSB受到地下白蚁侵蚀的抗性。实验中所有生产OSB的参数都比CSA(加拿大标准协会)0437.0标准的最低要求要高。展开更多
Gas-boriding in N2-H2-BCl3 atmosphere resulted in the formation of a thick layer on Inconel 600 alloy.The microstructure of layer produced at 920℃for 2 h consisted of a mixture of chromium borides and nickel borides....Gas-boriding in N2-H2-BCl3 atmosphere resulted in the formation of a thick layer on Inconel 600 alloy.The microstructure of layer produced at 920℃for 2 h consisted of a mixture of chromium borides and nickel borides.The objective of investigations was to determine the influence of the chemical and phase compositions of borided layer on its mechanical properties.The nanoindentation was carried out using Berkovich diamond tip under a load of 50 m N.The gas-borided layer was characterized by high indentation hardness HIT from 1542.6 HV to 2228.7 HV and high elastic modulus EIT from 226.9 to 296.4 GPa.It was found that the mixture with higher percentage of chromium borides was the reason for the increase in HIT and EIT values.The fracture toughness(KC)was measured using Vickers microindentation technique under a load of 0.98 N.The presence of high compressive stresses in normal direction to the top surface caused the strong anisotropy of the borided layer,in respect of fracture toughness.The high difference between the lowest(0.5763 MPa·m^1/2)and the highest(4.5794 MPa·m^1/2)fracture toughness was obtained.This situation was caused by the differences in chemical and phase compositions of tested areas,presence of porosity and residual stresses.Generally,the higher KC values were obtained in areas with lower chromium content.展开更多
The two-stage gas boriding in N_(2)−H_(2)−BCl_(3)atmosphere was applied to producing a two-zoned borided layer on Nisil-alloy.The process was carried out at 910℃ for 2 h.The microstructure consisted of two zones diff...The two-stage gas boriding in N_(2)−H_(2)−BCl_(3)atmosphere was applied to producing a two-zoned borided layer on Nisil-alloy.The process was carried out at 910℃ for 2 h.The microstructure consisted of two zones differing in their phase composition.The outer layer contained only a mixture of nickel borides(Ni_(2)B,Ni_(3)B)only.The inner zone contained additionally nickel silicides(Ni_(2)Si,Ni_(3)Si)occurring together with nickel borides.The aim of this study was to determine the presence of nickel silicides on the mechanical properties of the borided layer produced on Ni-based alloy.The hardness and elastic modulus were measured using the nanoindenter with a Berkovich diamond tip under a load of 50 mN.The average values of indentation hardness(HI)and indentation elastic modulus(E_(I))obtained in the outer zone were respectively(16.32±1.03)GPa and(232±16.15)GPa.The presence of nickel silicides in the inner zone reduced the indentation hardness(6.8−12.54 GPa)and elastic modulus(111.79−153.99 GPa).The fracture toughness of the boride layers was investigated using a Vickers microindentation under a load of 0.981 N.It was confirmed that the presence of nickel silicides caused an increase in brittleness(by about 40%)of the gas-borided layer.展开更多
In the continuous casting production of medium carbon steel (whose mass fraction of carbon is 0.09 % to 0.16 %) and high strength low alloy steel (whose mass fraction of Mn is 0.90 % to 1.40 %), flecks occurring the m...In the continuous casting production of medium carbon steel (whose mass fraction of carbon is 0.09 % to 0.16 %) and high strength low alloy steel (whose mass fraction of Mn is 0.90 % to 1.40 %), flecks occurring the most often are usually longitudinal and star cracks. In additional to the employment of a galvanized plate mould, two kinds of fluxes with special properties were studied and used to harmonize the conflicts between the function of heat transfer and lubrication. An industrial application revealed that the crystallizing temperature (Tc) and crystal ratio (R) of fluxes have a crucible effect on impeding the occurrence of above defects on a slab surface. In the case of slab section (180 to 240) mm(1000 to 1400) mm and casting speed Vc of (0.7 to 1.2) m/min, the optimized parameters of fluxes are Tc of (1170 to 1190) ℃, R of 80 % to 95 % for medium carbon steel, and Tc of (1100 to 1150) ℃, plus R of 40 % to 60 % for high strength low alloy steel.展开更多
The semi-circular bend(SCB) dynamic fracture toughness test is simulated using discrete element models. The influence of the frictional boundary condition, constitutive law and specimen thickness on the test measureme...The semi-circular bend(SCB) dynamic fracture toughness test is simulated using discrete element models. The influence of the frictional boundary condition, constitutive law and specimen thickness on the test measurements is investigated. It is found that friction between loading plates and the rock specimen affects the test results. Therefore, friction must be carefully considered to obtain accurate measurements. The simulation results also show that in contrast to the 2D model in which a rate-dependent cohesive law must be introduced, 3D models with a rate-independent law can produce good results. Furthermore, the study suggests that test measurements are seriously affected by specimen thickness; thus, full 3D modeling is required for simulation of the SCB test.展开更多
基金The National Natural Science Foundation of China(No.51378122)
文摘According to the winter temperature of Peking,the freeze-thaw（FT） condition in laboratory was determined.Seven groups of epoxy asphalt concrete（EAC） specimen were exposed to different FT cycles.The flexural modulus and fracture energy（G_F） of EAC exposed to different FT cycles were obtained through the 3-point bending test.Meanwhile,the plane strain fracture toughness（K_（IC）） of EAC was obtained through numerical simulation.The results show that the flexural modulus of the FT conditioned EAC samples decreases with the increase of FT cycles.The FT damage of flexural modulus is 60%after 30 FT cycles.Nevertheless,with the increase of FT cycles,the G_F and K_（IC） of EAC decrease first and then increase after 15 FT cycles.
文摘作为生产复合材料板的一种可供选择的原材料,竹材获得越来越多的关注。用Betung竹材(Dendrocalamus Asper(Schultes.F)Backer Ex Heyne,马来甜龙竹)制得的三层OSB来评估刨片结构长度和预处理技术对其物理力学性能,以及耐久性方面的影响。结果显示,在垂直于纹理方向上,刨片长度对于其断裂模量(MOR)和弹性模量(MOE)的影响很大。将刨片放入乙酸酐溶液中浸泡对于提高OSB尺寸的稳定性略有改善。在实验条件中,将板材浸入冷水和乙酸酐溶液提高了OSB受到地下白蚁侵蚀的抗性。实验中所有生产OSB的参数都比CSA(加拿大标准协会)0437.0标准的最低要求要高。
基金financially supported by Ministry of ScienceHigher Education in Poland as a part of the “02/24/DSPB” Project
文摘Gas-boriding in N2-H2-BCl3 atmosphere resulted in the formation of a thick layer on Inconel 600 alloy.The microstructure of layer produced at 920℃for 2 h consisted of a mixture of chromium borides and nickel borides.The objective of investigations was to determine the influence of the chemical and phase compositions of borided layer on its mechanical properties.The nanoindentation was carried out using Berkovich diamond tip under a load of 50 m N.The gas-borided layer was characterized by high indentation hardness HIT from 1542.6 HV to 2228.7 HV and high elastic modulus EIT from 226.9 to 296.4 GPa.It was found that the mixture with higher percentage of chromium borides was the reason for the increase in HIT and EIT values.The fracture toughness(KC)was measured using Vickers microindentation technique under a load of 0.98 N.The presence of high compressive stresses in normal direction to the top surface caused the strong anisotropy of the borided layer,in respect of fracture toughness.The high difference between the lowest(0.5763 MPa·m^1/2)and the highest(4.5794 MPa·m^1/2)fracture toughness was obtained.This situation was caused by the differences in chemical and phase compositions of tested areas,presence of porosity and residual stresses.Generally,the higher KC values were obtained in areas with lower chromium content.
基金This work has been financially supported by Ministry of Science and Higher Education in Poland as a part of the Project No.0513/SBAD.
文摘The two-stage gas boriding in N_(2)−H_(2)−BCl_(3)atmosphere was applied to producing a two-zoned borided layer on Nisil-alloy.The process was carried out at 910℃ for 2 h.The microstructure consisted of two zones differing in their phase composition.The outer layer contained only a mixture of nickel borides(Ni_(2)B,Ni_(3)B)only.The inner zone contained additionally nickel silicides(Ni_(2)Si,Ni_(3)Si)occurring together with nickel borides.The aim of this study was to determine the presence of nickel silicides on the mechanical properties of the borided layer produced on Ni-based alloy.The hardness and elastic modulus were measured using the nanoindenter with a Berkovich diamond tip under a load of 50 mN.The average values of indentation hardness(HI)and indentation elastic modulus(E_(I))obtained in the outer zone were respectively(16.32±1.03)GPa and(232±16.15)GPa.The presence of nickel silicides in the inner zone reduced the indentation hardness(6.8−12.54 GPa)and elastic modulus(111.79−153.99 GPa).The fracture toughness of the boride layers was investigated using a Vickers microindentation under a load of 0.981 N.It was confirmed that the presence of nickel silicides caused an increase in brittleness(by about 40%)of the gas-borided layer.
文摘In the continuous casting production of medium carbon steel (whose mass fraction of carbon is 0.09 % to 0.16 %) and high strength low alloy steel (whose mass fraction of Mn is 0.90 % to 1.40 %), flecks occurring the most often are usually longitudinal and star cracks. In additional to the employment of a galvanized plate mould, two kinds of fluxes with special properties were studied and used to harmonize the conflicts between the function of heat transfer and lubrication. An industrial application revealed that the crystallizing temperature (Tc) and crystal ratio (R) of fluxes have a crucible effect on impeding the occurrence of above defects on a slab surface. In the case of slab section (180 to 240) mm(1000 to 1400) mm and casting speed Vc of (0.7 to 1.2) m/min, the optimized parameters of fluxes are Tc of (1170 to 1190) ℃, R of 80 % to 95 % for medium carbon steel, and Tc of (1100 to 1150) ℃, plus R of 40 % to 60 % for high strength low alloy steel.
基金supported by the Australian Research Council(Grant No.DE130100457)State Key Laboratory of Hydraulics and Mountain River Engineering(SKHL)(Grant No.SKHL1407)the National Natural Science Foundation of China(Grant Nos.41202207,51204112 and 2015JY0045)
文摘The semi-circular bend(SCB) dynamic fracture toughness test is simulated using discrete element models. The influence of the frictional boundary condition, constitutive law and specimen thickness on the test measurements is investigated. It is found that friction between loading plates and the rock specimen affects the test results. Therefore, friction must be carefully considered to obtain accurate measurements. The simulation results also show that in contrast to the 2D model in which a rate-dependent cohesive law must be introduced, 3D models with a rate-independent law can produce good results. Furthermore, the study suggests that test measurements are seriously affected by specimen thickness; thus, full 3D modeling is required for simulation of the SCB test.
