浅析方格网法在杨房沟水电站工程计量中的应用

工程计量需要有较强的说服力和较为严谨的计算过程,一般使用横断面进行工程量计量。为了确定方格网土方计算方法在雅砻江杨房沟水电站前期工程计量中的适用性,通过对方格网土方计算原理的探究,分析了其使用范围、适用条件、方格宽度对计算成果的影响及其取值原则。以杨房沟导流洞进口底板地质超挖工程量计量为例,分析了使用方格网土方计算方法的具体应用步骤和其计算快速高效的特点,以及与断面计算方法相比较具有的优势。结果表明,该方法在某些小范围的土石方工程计量中应用,可以提高工程量计量的效率和可靠性。

Mechanical analysis of transmission lines based on linear sliding cable element

In order to study the sliding characteristics when the cable structures are connected with other rods, a string of sliding cable dements （SCE） consisting of one active threenode SCE passing through the sliding point and multiple inactive two-node SCEs is put forward. Based on the updated Lagrangian formulation, the geometric nonlinear stiffness matrix of the three-node straight sliding cable dement is deduced. The examples about two-span and three-span continuous cable structures are studied to verify the effectiveness of the derived SCE. Comparing the cable tension of SCE with the existing research results, the calculating results show that the error is less than 1%. The sliding characteristics should be considered in practical engineering because of the obvious difference between the cable tension of the SCE and that of the cable element without considering sliding characteristics.

Dynamic Cell Range Expansion-based Interference Coordination Scheme in Next Generation Wireless Networks

Deploying Picocell Base Station(PBS) throughout a Macrocell is a promising solution for capacity improvement in the next generation wireless networks.However,the strong received power from Macrocell Base Station(MBS) makes the areas of Picocell narrow and limits the gain of cell splitting.In this paper,we firstly propose a Dynamic Cell Range Expansion(DCRE) strategy.By expanding the coverage of the cell,we aim to balance the network load between MBS and PBS.Then,we present a cooperative Resource block and Power Allocation Scheme(coRPAS)based on DCRE.The objective of coRPAS is to decrease interference caused by MBS and Macrocell User Equipments,by which we can expand regions of Picocell User Equipments.Simulation results demonstrate the superiority of our method through comparing with other existing methods.

The effect of grid shape on the properties of transparent conductive films based on flexographic printing

The effect of grid shape on the properties of transparent conductive films(TCFs) is theoretically analyzed and experimentally verified. The light transmittance by three types of grid shapes: triangle, square and hexagon have been theoretically calculated and simulated. It was found that hexagonal grid unit has the highest light transmittance limit under the practical lattice parameters and its decrease in light transmittance caused by the increase of line width in printing process is the least. The grid of three different shapes with same theoretical transmittance is fabricated through flexographic printing. The result shows that the actual light transmittance of the printed TCFs is lower than its theoretical value because of the inevitable width increase of printed grid lines, with slight difference between the three shapes. However, it is greatly different in terms of conductivity, leading to variation in the quality factor Q(defined as the ratio of light transmittance to total resistance) which represents the performance of TCFs. The Q of hexagonal grid(6.04) is the highest, which is 21% higher than that of the square grid.

A partition-of-unity based three-node triangular element with continuous nodal stress using radial-polynomial basis functions

A partition-of-unity （PU） based ＂FE-Meshfree＂ three-node triangular element （Trig3-RPIM） was recently developed for linear elastic problems. This Trig3-RPIM element employs hybrid shape functions that combine the shape functions of three-node triangular element （Trig3） and radial-polynomial basis functions for the purpose of synergizing the merits of both finite element method and meshfree method. Although Trig3-RPIM element is capable of obtaining higher accuracy and convergence rate than the Trig3 element and four-node iso-parametric quadrilateral element without adding extra nodes or degrees of freedom （DOFs）, the nodal stress field through Trig3-RP1M element is not continuous and extra stress smooth operations are still needed in the post processing stage. To further improve the property of Trig3-RPIM element, a new PU-based triangular element with continuous nodal stress, called Trig3-RPIMcns, is developed. Numerical examples including several linear, free vibration and forced vibration test problems, have confirmed the correctness and feasibility of the proposed Trig3-RPIMcns element.