The quench sensitivity of 6063 alloy was investigated via constructing time-temperature-property（TTP） curves by interrupted quenching technique and transmission electron microscopy（TEM） analysis.The results show t...The quench sensitivity of 6063 alloy was investigated via constructing time-temperature-property（TTP） curves by interrupted quenching technique and transmission electron microscopy（TEM） analysis.The results show that the quench sensitivity of 6063 alloy is lower than that of 6061 or 6082 alloy,and the critical temperature ranges from 300 to 410℃ with the nose temperature of about 360℃.From TEM analysis,heterogeneous precipitate β-Mg2Si is prior to nucleate on the（AlxFeySiz） dispersoids in the critical temperature range,and grows up most rapidly at the nose temperature of 360℃.The heterogeneous precipitation leads to a low concentration of solute,which consequently reduces the amount of the strengthening phase β＇＇ after aging.In the large-scale industrial production of 6063 alloy,the cooling rate during quenching should be enhanced as high as possible in the quenching sensitive temperature range（410-300℃） to suppress the heterogeneous precipitation to get optimal mechanical properties,and it should be slowed down properly from the solution temperature to 410℃ and below 300℃ to reduce the residual stress.展开更多
The quenching sensitivity of AA7136 alloy was investigated by time−temperature−property(TTP)diagrams,and the heterogeneous precipitation behavior during isothermal holding was investigated using scanning electron micr...The quenching sensitivity of AA7136 alloy was investigated by time−temperature−property(TTP)diagrams,and the heterogeneous precipitation behavior during isothermal holding was investigated using scanning electron microscopy,scanning transmission electron microscopy and high resolution transmission electron microscopy.Based on 99.5%TTP diagram,the nose temperature is determined to be about 346℃ with the transformation time of about 0.245 s.The precipitation ofη(MgZn_(2)),T(Al_(2)Zn_(3)Mg_(3)),S(Al_(2)CuMg)or Cu−Zn-rich Y phases can be found depending on isothermal holding temperature and time,and it is described in a time−temperature−precipitation diagram.The size and area fraction of isothermal holding induced phase particles increase,which results in the decrease of hardness of samples after aging.The quantitative contribution to loss of hardness by grain boundaries/subgrain boundaries and dispersoids in the matrix is discussed based on the amount of heterogeneous precipitation related to them.展开更多
The influence of operation parameters on the adsorption performance of protein (bovin serum albumin, BSA) in an expanded bed was studied using Streamline diethyl aminoethyl (DEAE). The result of residence time distrib...The influence of operation parameters on the adsorption performance of protein (bovin serum albumin, BSA) in an expanded bed was studied using Streamline diethyl aminoethyl (DEAE). The result of residence time distributions (RTD) and breakthrough curves showed that adsorption performance of the expanded bed could not be improved by increasing the flow velocity at the range from 16ml·min-1 to 26ml·min-1. The increase of protein concentration from 0.5 mg·ml to 2 mg·ml-1 resulted in poor adsorption performance. With increasing temperature from 5℃ to 30℃ and the sedimented bed height from 11.5cm to 22.5cm, the adsorption characteristics in the expanded bed were improved.展开更多
文摘The quench sensitivity of 6063 alloy was investigated via constructing time-temperature-property（TTP） curves by interrupted quenching technique and transmission electron microscopy（TEM） analysis.The results show that the quench sensitivity of 6063 alloy is lower than that of 6061 or 6082 alloy,and the critical temperature ranges from 300 to 410℃ with the nose temperature of about 360℃.From TEM analysis,heterogeneous precipitate β-Mg2Si is prior to nucleate on the（AlxFeySiz） dispersoids in the critical temperature range,and grows up most rapidly at the nose temperature of 360℃.The heterogeneous precipitation leads to a low concentration of solute,which consequently reduces the amount of the strengthening phase β＇＇ after aging.In the large-scale industrial production of 6063 alloy,the cooling rate during quenching should be enhanced as high as possible in the quenching sensitive temperature range（410-300℃） to suppress the heterogeneous precipitation to get optimal mechanical properties,and it should be slowed down properly from the solution temperature to 410℃ and below 300℃ to reduce the residual stress.
基金financial supports from the National Key Research and Development Program of China (No. 2016YFB0300901)the Scientific Research Project of Inner Mongolia Colleges and Universities, China (No. NJZY21092)。
文摘The quenching sensitivity of AA7136 alloy was investigated by time−temperature−property(TTP)diagrams,and the heterogeneous precipitation behavior during isothermal holding was investigated using scanning electron microscopy,scanning transmission electron microscopy and high resolution transmission electron microscopy.Based on 99.5%TTP diagram,the nose temperature is determined to be about 346℃ with the transformation time of about 0.245 s.The precipitation ofη(MgZn_(2)),T(Al_(2)Zn_(3)Mg_(3)),S(Al_(2)CuMg)or Cu−Zn-rich Y phases can be found depending on isothermal holding temperature and time,and it is described in a time−temperature−precipitation diagram.The size and area fraction of isothermal holding induced phase particles increase,which results in the decrease of hardness of samples after aging.The quantitative contribution to loss of hardness by grain boundaries/subgrain boundaries and dispersoids in the matrix is discussed based on the amount of heterogeneous precipitation related to them.
基金Supported by the National Natural Science Foundation of China(No.29736180).
文摘The influence of operation parameters on the adsorption performance of protein (bovin serum albumin, BSA) in an expanded bed was studied using Streamline diethyl aminoethyl (DEAE). The result of residence time distributions (RTD) and breakthrough curves showed that adsorption performance of the expanded bed could not be improved by increasing the flow velocity at the range from 16ml·min-1 to 26ml·min-1. The increase of protein concentration from 0.5 mg·ml to 2 mg·ml-1 resulted in poor adsorption performance. With increasing temperature from 5℃ to 30℃ and the sedimented bed height from 11.5cm to 22.5cm, the adsorption characteristics in the expanded bed were improved.
