The ductility and plastic asymmetry of an as-annealed magnesium alloy plate were studied in compression through combined process of torsion and subsequent annealing by optical microscope and EBSD. The yield strength...The ductility and plastic asymmetry of an as-annealed magnesium alloy plate were studied in compression through combined process of torsion and subsequent annealing by optical microscope and EBSD. The yield strength（YS） and ultimate compression strength（UCS） as well as the compression ductility（CD） were simultaneously raised by prior torsion at room temperature. The CD was further enhanced by subsequent annealing. Also, the torqued sample followed by annealing experienced a rising CD with the increase in prior strain, leading to the maximum true strain of 0.279, which is twice that of the as-annealed original one. The sample showed a largely reduced tension-compression yield asymmetry by subjecting to pre-torsion alone or combined with a subsequent annealing. The enhanced ductility and reduced asymmetry are attributed to the development of a gradient microstructure with refined grains, and also randomization of the weakened texture due to torsion and subsequent annealing.展开更多
Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dyna...Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.展开更多
To deeply understand and even describe the evolutions of the low-energy twin boundary density(BLDΣ3n)in a thermal-plastic deformation process,an improved twin density model as a function of average grain size and sto...To deeply understand and even describe the evolutions of the low-energy twin boundary density(BLDΣ3n)in a thermal-plastic deformation process,an improved twin density model as a function of average grain size and stored energy is developed.For Nimonic 80A superalloy,the model is solved based on the EBSD statistical results of grain size and BLDΣ3n in the specimens compressed at temperatures of 1273−1423 K and strain rates of 0.001−10 s−1.The corresponding relationships of BLDΣ3n with stored energy and grain size varying with temperature and strain rate are clarified by the superimposed contour plot maps.It is summarized that BLDΣ3n increases with increasing stored energy and decreasing grain size,and higher BLDΣ3n with finer grains corresponds with lower temperatures and higher strain rates.Such relationships are described by the improved twin density model,and the prediction tolerance of the solved model is limited in 2.8%.展开更多
基金Project(51474241)supported by the National Natural Science Foundation of ChinaProject(2013CB632204)supported by the National Basic Research Program of China
文摘The ductility and plastic asymmetry of an as-annealed magnesium alloy plate were studied in compression through combined process of torsion and subsequent annealing by optical microscope and EBSD. The yield strength（YS） and ultimate compression strength（UCS） as well as the compression ductility（CD） were simultaneously raised by prior torsion at room temperature. The CD was further enhanced by subsequent annealing. Also, the torqued sample followed by annealing experienced a rising CD with the increase in prior strain, leading to the maximum true strain of 0.279, which is twice that of the as-annealed original one. The sample showed a largely reduced tension-compression yield asymmetry by subjecting to pre-torsion alone or combined with a subsequent annealing. The enhanced ductility and reduced asymmetry are attributed to the development of a gradient microstructure with refined grains, and also randomization of the weakened texture due to torsion and subsequent annealing.
基金Project (14JJ6047) supported by the Natural Science Foundation of Hunan Province,ChinaProject (51274092) supported by the National Natural Science Foundation of ChinaProject (20120161110040) supported by the Doctoral Program of Higher Education ofChina
文摘Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.
基金the financial supports from Chongqing Basic Research and Frontier Exploration Program, China (cstc2018jcyj AX0459)the Fundamental Research Funds for the Central Universities, China (2019CDQYTM027, 2019CDJGFCL003, 2018CDPTCG0001-6)Open Fund of State Key Laboratory of Materials Processing and Die & Mould Technology, China (P2020-001)
文摘To deeply understand and even describe the evolutions of the low-energy twin boundary density(BLDΣ3n)in a thermal-plastic deformation process,an improved twin density model as a function of average grain size and stored energy is developed.For Nimonic 80A superalloy,the model is solved based on the EBSD statistical results of grain size and BLDΣ3n in the specimens compressed at temperatures of 1273−1423 K and strain rates of 0.001−10 s−1.The corresponding relationships of BLDΣ3n with stored energy and grain size varying with temperature and strain rate are clarified by the superimposed contour plot maps.It is summarized that BLDΣ3n increases with increasing stored energy and decreasing grain size,and higher BLDΣ3n with finer grains corresponds with lower temperatures and higher strain rates.Such relationships are described by the improved twin density model,and the prediction tolerance of the solved model is limited in 2.8%.
