激光多次熔凝Zr55Cu30Al10Ni5非晶合金的晶化形态与演化机理

采用脉冲激光对Zr55Cu30Al10Ni5非晶合金板进行激光多次熔凝,研究了激光多次熔凝时热影响区的晶化相形态随着熔凝次数增加时的演化规律。结果表明,随着熔凝次数的增加,晶粒数量逐渐增加,晶粒尺寸逐渐变大。随着晶粒的长大,卷入熔池内的晶粒造成的晶化也越来越显著。激光多次熔凝非晶合金时,热影响区内的晶粒尺寸和数量都随熔凝次数的增加而线性增加,不同非晶合金板的形核率和生长速率基本接近,但初始晶粒数量和初始晶粒尺寸不同,这和铜模铸造制备非晶合金板时的具体冷却过程差异有关。

Effect of ultrasonic on morphology of primary Mg_2Si in in-situ Mg_2Si/Al composite

Effects of ultrasonic on morphologies of primary Mg2Si crystals in in-situ Mg2Si/A1 composite were investigated by metallographic microscopy and field emission scanning electron microscopy. The results show that the mean grain size of primary MgESi crystals is refined from 150 to 20 μm by high intensity ultrasonic, and the morphologies of primary MgESi crystals are changed as well. Optical microscopy reveals that primary MgESi crystals without ultrasonic vibration exhibit coarse particles with cavities, in which eutectic structures grow. However, primary Mg2Si crystals with ultrasonic vibration appear fine grains without any cavity. Three-dimensional morphologies of primary Mg2Si without ultrasonic vibration display octahedron and tetrakaidecahedron with hopper-like hole in the crystals. After ultrasonic vibration, primary Mg2Si particles become solid crystals with rounded comers and edges.

Modeling of strain hardening and dynamic recrystallization of ZK60 magnesium alloy during hot deformation

The flow stress behavior of ZK60 alloy at elevated temperature was investigated. The strain hardening and dynamic recrystallization of the alloy were modeled by Kocks-Meching model and Avrami equation, respectively. A new constitutive equation during hot deformation was constructed to predict the flow stress considering the dynamic recrystallization. The results show that the flow stress curves predicted by the proposed equation have high correlation coefficients with the experimental data, which confirms that the developed model is accurate and effective to establish the flow stress equation of ZK60 magnesium alloy during hot deformation. Microstructure observation shows that dynamic recovery occurs in the initial stage of hot deformation. However, the microstructure turns to recrvstallization structure as the strain increases.

Microstructure evolution and dislocation configurations in nanostructured Al-Mg alloys processed by high pressure torsion

Microstructure evolution and dislocation configurations in nanostructured Al–Mg alloys processed by high pressure torsion （HPT） were analyzed by transmission electron microscopy （TEM） and high-resolution TEM （HRTEM）. The results show that the grains less than 100 nm have sharp grain boundaries （GBs） and are completely free of dislocations. In contrast, a high density of dislocation as high as 1017 m^-2 exists within the grains larger than 200 nm and these larger grains are usually separated into subgrains and dislocation cells. The dislocations are 60° full dislocations with Burgers vectors of 1/2〈110〉and most of them appear as dipoles and loops. The microtwins and stacking faults （SFs） formed by the Shockley partials from the dissociation of both the 60° mixed dislocation and 0° screw dislocation in ultrafine grains were simultaneously observed by HRTEM in the HPT Al–Mg alloys. These results suggest that partial dislocation emissions, as well as the activation of partial dislocations could also become a deformation mechanism in ultrafine-grained aluminum during severe plastic deformation. The grain refinement mechanism associated with the very high local dislocation density, the dislocation cells and the non-equilibrium GBs, as well as the SFs and microtwins in the HPT Al-Mg alloys were proposed.

Hot deformation and processing map of GH3535 superalloy

The hot deformation behavior of GH3535 superalloy was investigated by hot compression tests in the temperature range of 1000-1200 °C and strain rate range of 0.01-50 s-1. The activation energy is about 356.3 k J/mol, and the flow curves and processing map were developed on the basis of experimental data. The processing map exhibits a stable domain which occurs in the strain rate range of 0.01-1 s-1 at all the temperatures and a instable domain which occurs in the strain rate range of 1-50 s-1. Microstructural observations reveal that the full dynamic recrystallization（DRX） occurs in the conditions of（1150 °C, 0.01 s-1）,（1200 °C, 0.01 s-1） and（1200 °C, 0.1 s-1） with different grain sizes and undissolved carbides. The flow localization and cracks occur in the regime of flow instability.

Preparation of tetrapod-like ZnO whiskers from waste hot dipping zinc

Large and uniform tetrapod-like ZnO whiskers （T-ZnO） were prepared from waste hot dipping zinc by vapor oxidation and examined by means of X-ray diffraction and ICP-AES analysis and scanning electron microscope. The products are pure hexagonal wurtzite crystals with tetrapod shape and edge size of center body 56 μm and needle length of 100130 μm. The size and shape of ZnO particles are fully controlled by the growth conditions and T-ZnO can be obtained only at 8501 000 ℃ and total gas flow rate ranging from 40 to 250 L·h-1 in which the size of the T-ZnO particles varies slightly with temperature. The process of the formation of T-ZnO is that T-ZnO may nucleate at the initial stage with a complete tetrapod shape and develop to the large size, but not the process of （preferential） growth of octahedral nuclei and subsequent growth of the needles. The experiment presents a new method to prepare T-ZnO economically by using the waste hot dipping zinc.

Deformation banding in β working of two-phase TA15 titanium alloy

To study deformation banding inβworking of TA15titanium alloy,hot simulation compression experiments were carried out on a Gleeble3500thermal simulator,and the microstructure was investigated by optical microscopy(OM)and electron backscattered diffraction(EBSD).It is found that inβworking of TA15titanium alloy,deformation banding is still an important grain refinement mechanism up to temperature as high as0.7Tm(Tm is the melting temperature).Boundaries of deformation bands(DBBs)may be sharp or diffusive.Sharp DBBs retard discontinuous dynamic recrystallization(DDRX)by prohibiting nucleation,while the diffusive ones are sources of continuous dynamic recrystallization(CDRX).Deformation banding is more significant at high strain rate and large initial grain size.The average width of grain subdivisions is sensitive to strain rate but less affected by temperature and initial grain size.Multi-directional forging which produces crossing DDBs is potential to refine microstructure of small-size forgings.

Ra's Abdah of the north Eastern Desert of Egypt:the role of granitic dykes in the formation of radioactive mineralization,evidenced by zircon morphology and chemistry

Syenogranitic dykes in the north of Egypt's Eastern Desert are of geological and economic interest because of the presence of magmatic and supergene enrichment of radioactive mineralization. Zircon crystal morphology within the syenogranitic dykes allows precise definition of sub-alkaline series granites and crystallized at mean temperature of about 637 °C. The growth pattern of the zircons suggest magmatic and hydrothermal origins of radioactive mineralization. Hydrothermal processes are responsible for the formation of significant zircon overgrowth; high U-zircon margins might have occurred contemporaneously with the emplacement of syenogranitic dykes which show anomalous uranium(e U) and thorium(e Th) contents of up to 1386 and 7330 ppm, respectively.Zircon chemistry revealed a relative increase of Hf consistent with decreasing Zr content, suggesting the replacement of Zr by Hf during hydrothermal activity.Visible uranium mineralization is present and recognized by the presence of uranophane and autunite.

Studies on the Crystallization Properties and Morphology Structure of the Cationic Dyeable Polypropylene Fibers

The crystallization properties and morphology structure of the cationic dyeable polypropylene fibers which were produced by the blending spinning method were studied by making use of X-ray and scanning electron microscopy (SEM). It comes to the conclusions that the larger the crystallite size in the fibers is , the better the dyeable properties of the fibers are and there is a little compatibility between the dyeable agent and polypropylene resin. And the dye-uptake of the fibers may be up to 90% because the dyeable agent can uniformly be scattered in polypropylene.

Effect of solidification rate on MC-type carbide morphology in single crystal Ni-base superalloy AM3

In order to study the effect of the withdrawing rate on carbide morphology,MC-type carbide in single crystal superalloy AM3 was systematically investigated with sample growth rates from 3.5 μm/s to 500 μm/s.The carbide morphologies were investigated by scanning electron microscopy(SEM),and the electron probe microanalysis(EPMA) was used to characterize the carbide composition.The results indicate that the solidification rate is the important factor governing MC carbide growth morphology,size and distribution,composition and growth mechanism.With the increase of withdrawing rate,nodular,rod-like,Chinese script types of carbide morphology are observed.For the low withdrawing rate,with the increase of withdrawing rate,the carbide size becomes larger.For the case of dendritic interface,the carbide size becomes smaller with refinement of dendrites as withdrawing rate increases.The volume fraction of carbides increases with the withdrawing rate increasing.

Relationship Between Iron Oxides and Surface Charge Characteristics in Soils

The relationship between iron oxides and surface charge characteristics in variable charge soils ( latosol and red earth ) was studied in following three ways. ( 1 ) Remove free iron oxides ( Fed ) and amorphous iron oxides ( Feo ) from the soils with sodium dithionite and acid ammonium oxalate solution respectively. ( 2 ) Add 2% glucose ( on the basis of air-dry soil weight ) to soils and incubate under submerged condition to activate iron oxides, and then the mixtures are dehydrated and air-dried to age iron oxides. ( 3 ) Precipitate various crystalline forms of iron oxides onto kaolinite. The results showed that free iron oxides ( Fed ) were the chief carrier of variable positive charges. Of which crystalline iron oxides ( Fed-Feo ) presented mainly as discrete particles in the soils and could only play a role of the carrier of positive charges, and did little influence on negative charges. Whereas the amorphous iron oxides ( Feo ) , which presented mainly as a coating with a large specific surface area, not only had positive charges, but also blocked the negative charge sites in soils. Submerged incubation activated iron oxides in the soils, and increased the amount of amorphous iron oxides and the degree of activation of iron oxide, which resulted in the increase of positive and negative charges of soils. Dehydration and air-dry aged iron oxides in soils and decreased the amount of amorphous iron oxides and the degree of activation of iron oxide, and also led to the decrease of positive and negative charges. Both the submerged incubation and the dehydration and air-dry had no significant influence on net charges. Precipitation of iron oxides onto kaolinite markedly increased positive charges and decreased negative charges. Amorphous iron oxide having a larger surface area contributed more positive charge sites and blocked more negative charge sites in kaolinite than crystalline goethite.

Crystal Growth,Structure and Morphology of Rifapentine Methanol Solvate

Rifapentine, an important antibiotic, was crystallized from methanol solvent in the form of its methanol solvate. The crystal structure of rifapentine methanol solvate belongs to monoclinic, space group P21, with the unit cell parameters of a = 1.2278（3） nm, b = 1.9768（4） rim, c = 1.2473（3） nm, Z= 2, and β = 112.35（3）. The parallelepiped.morphology was also predicted by Materials Studio simulation program.. The influence of intermolecular in-teraction was taken into account in the attachment energy model. The crystal shape fits the calculated morphology well, which was performed on the potential energy minimized model using a generic DREIDING 2.21 force fieldand developed minimization protocol with derived＇partial charges.

Effects of synthesis factors on the morphology, crystallinity and crystal size of hydroxyapatite precipitation

The growing necessity of biomaterials has increased the interest in hydroxyapatite. Small differences in particle sizes, stoichiometry, morphology, crystallinity could lead to different clinical behaviors. In the present work, stoichiometry and nanocrystal hydroxyapatite were prepared by wet chemical precipitation method. The effects of concentration of reagents, reaction temperatures and reaction time were studied. Transmission Electron Microscopy, Electron Diffraction, X - ray Diffraction, Fourier Transform Infrared Spectroscopy, arid Inductively Coupled Plasma Spectroscopy were used to characterize the precipitated hydroxyapatite powders. X - ray Diffraction and TEM micrographs results showed that crystallinity, morphology and particle sizes were largely dependent on reaction temperature. Chemical analysis showed that the purity of the precipitated hydroxyapatite depends on reaction time and reaction temperature. Degree of supersaturation and stirring could affect the crystallization process. Particles showed acicular morphology, and had a size of 20 - 30 nm in length at 20 ℃ and 37 ℃ and 150 - 160 nm in length at 75 ℃. Particles were monocrystalline at 20 ℃ and 37 ℃ , and were polycrystalline at 55 ℃ and 75 ℃. The results showed that hydroxyapatite powders with different particle size and morphology could be obtained with carefully controlled reaction conditions.

Mechanism of Ag_3Sn grain growth in Ag/Sn transient liquid phase soldering

Transient liquid phase(TLP)bonding is a potential high-temperature(HT)electron packaging technology that is used inthe interconnection of wide band-gap semiconductors.This study focused on the mechanism of intermetallic compounds(IMCs)evolution in Ag/Sn TLP soldering at different temperatures.Experimental results indicated that morphologies of Ag3Sn grains mainlywere scallop-type,and some other shapes such as prism,needle,hollow column,sheet and wire of Ag3Sn grains were also observed,which was resulted from their anisotropic growths.However,the scallop-type Ag3Sn layer turned into more planar with prolongingsoldering time,due to grain coarsening and anisotropic mass flow of Ag atoms from substrate.Furthermore,a great amount ofnano-Ag3Sn particles were found on the surfaces of Ag3Sn grains,which were formed in Ag-rich areas of the molten Sn and adsorbedby the Ag3Sn grains during solidification process.Growth kinetics of the Ag3Sn IMCs in TLP soldering followed a parabolicrelationship with soldering time,and the growth rate constants of250,280and320°C were calculated as5.83×10-15m2/s,7.83×10-15m2/s and2.83×10-14m2/s,respectively.Accordingly,the activation energy of the reaction was estimated about58.89kJ/mol.

Synthesis of butterfly-like BiVO4/RGO nanocomposites and their photocatalytic activities

A simple and high efficient method was proposed for the synthesis of uniform three dimensional （3D） BiVO4/reduced graphene oxide （RGO） nanocomposite photocatalyst by adopting the microwave assistant and using Bi （NO3）3·5H2O, graphene oxide （GO） and NH4VO3 as precursor. The as-obtained composites were well characterized with the aid of various techniques to study the morphology, structure, composition, optimal and electrical property. In the as-obtained composites, the GO sheets were fully reduced into RGO, and monoclinic structure BiVO4 crystallized completely into butterfly-like BiVO4 lamellas and well bonded with the RGO lamellas. The length and the width of the butterfly-like BiVO4 particle were about 1.5 μm, and the thickness of the flake was about 20 nm. Photocatalytic performances of BiVO4/RGO composite and pure BiVO4 particle have been evaluated by investigating the reduction of Cr（VI） ion-contained wastewater under simulated solar light irradiation, where the BiVO4/RGO composite displayed enhanced photocatalytic activity. It is found that the pseudo-first-order rate constants （k） for the photocatalytic reduction of Cr （VI） by BiVO4/RGO composite was about 4 times as high as that of the pure BiVO4. The present work suggested that the combination of BiVO4 and RGO displayed a remarkable synergistic effect, which led to enhanced photo-catalytic activity on Cr（VI） reduction.

The Preparation of Ultra-fine Calcium Carbonate and Its properties Study

This article adopts the double decomposition method, select the appropriate experimental conditions and operation process, respectively add appropriate amount of sodium carboxymethyl cellulose （CMC） as crystal control agent to study the influence of crystalline of ultrafine calcium carbonate. The experimental results show that the different concentrations of CMC as crystal control agent on the morphology and crystal structure of calcium carbonate have obvious effect, which emerge morphology change from square to spherical, crystalline transition from calcite to aragonite. Thus, the results provide experimental data and theoretical basis for the use of different additives, and provide experimental basis and feasible solution for this kind of reaction.

Mineralogical and micromorphological characteristics of Si-Fe-Mn oxyhydroxides from the PACMANUS hydrothermal field, Eastern Manus Basin

The mineralogical and micromorphological characteristics of Si-Fe-Mn oxyhydroxides from the dacite-hosted PACMANUS hydrothermal field were analyzed.The samples are poorly crystallized Si-Fe-Mn oxyhydroxides with minor birnessite, todorokite, nontronite, goethite, and opal-A.There are some microtextures which are rather like fossil microbes such as the filamentous silica and the hollow pipes.Flakes of nontronite crystals are found either forming a honeycomb texture or distrib- uted on the surface of the hollow pipes.Nontronite is the product precipitated from low-temperature hydrothermal fluids, and microbes may play a role in its formation.Si-Fe-Mn oxyhydroxides have two kinds of nuclei: Si-Mn nuclei and Si nuclei, both enveloped by the similar Si-Fe outer layer, existing in the rod-shaped oxyhydroxide and spheroidal oxyhydroxide, respectively.In the Si-Mn nuclei, the concentration of SiO2 is between 39.32 wt% and 86.31 wt%, and MnO concentration is between 4.97 wt% and 27.01 wt%, but Fe2O3 concentration is very low (0.54 wt%-3.43 wt%).In the Si nucleus the concentration of SiO2 is 90.17 wt%, but concentration of MnO and Fe2O3 are low, with 0.06 wt% and 3.47 wt%, respectively.The formation of the Si-Mn nucleus is closely related to microbes, whereas the Si nucleus is of inorganic origin.

Growth control of peptide-nanotube spherulitic films： Experiments and simulations

Multi-hierarchical self-assembly （MHSA） is a key process responsible for the spontaneous formation of many complex structures. However, because of the complexity of the process, the underlying mechanism remains largely unclear. Thus, a deeper understanding of MHSA is required, especially for the preparation of MHSA systems via bottom-up methodologies. We show here, experimentally and theoretically, that the complex-formation MHSA of peptide nanotube films can be controlled solely by manipulating the experimental parameter of humidity. Furthermore, we identify growth-front nucleation （GFN; the formation of new grains at the perimeter） as the physical background for the observed morphological transitions by correlating experimental observations with phase-field modeling of the morphological evolution. Our findings indicate a simple way to control multi-hierarchical morphologies, crucial for the employment of bottom-up techniques in constructing complex structures for practical applications.

Preparation of Highly Crystalline Graphitic Nanocarbon for the Electro-Oxidation of Methanol

Highly crystalline graphitic nanocarbons （GNC） have been prepared by the wet-air treatment of hydrothermally- derived graphitic porous carbon. The materials were characterized by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and electrochemical methods. The experimental results revealed that the treatment temperature has a significant effect on the morphology and degree of graphitic crystallinity. When GNC was treated at 450 ~C under a wet-air atmosphere, the product （GNC-450） consisted of aggregates of silkworm-shaped carbon nanoparticles with enhanced graphitic characteristics. GNC-450 was evaluated as a catalyst support in the electro-oxidation of methanol. The Pt/GNC-450 catalyst contained smaller Pt particles and had a higher electrochemically active surface area than a commercial carbon black-supported Pt catalyst. In the electro-oxidation of methanol, the Pt/GNC-450 catalyst showed the highest performance among the Pt catalysts examined in this study. The superior catalytic performance appears to be closely related to the enhanced graphitic characteristics with highly dispersed Pt nanoparticles on the graphitic layers, which have a positive effect on the electrochemical performance.