In order to improve the hydriding and dehydriding kinetics of the Mg2Ni-type alloys,Ni in the alloy is substituted by element Co. The nanocrystalline and amorphous Mg2Ni-type Mg2Ni1-xCox (x=0,0.1,0.2,0.3,0.4) alloys w...In order to improve the hydriding and dehydriding kinetics of the Mg2Ni-type alloys,Ni in the alloy is substituted by element Co. The nanocrystalline and amorphous Mg2Ni-type Mg2Ni1-xCox (x=0,0.1,0.2,0.3,0.4) alloys were synthesized by melt-spinning technique. The structures of the as-cast and spun alloys were studied with an X-ray diffractometer (XRD) and a high resolution transmission electronic microscope (HRTEM). An investigation on the thermal stability of the as-spun alloys was carried out with a differential scanning calorimeter (DSC). The hydrogen absorption and desorption kinetics of the alloys were measured with an automatically controlled Sieverts apparatus. The results demonstrate that the substitution of Co for Ni does not alter the major phase of Mg2Ni but results in the formation of secondary phase MgCo2. No amorphous phase is detected in the as-spun Co-free alloy,but a certain amount of amorphous phase is clearly found in the as-spun Co-containing alloys. The substitution of Co for Ni exerts a slight influence on the hydriding kinetics of the as-spun alloy. However,it dramatically enhances the dehydriding kinetics of the as-cast and spun alloys. As Co content (x) increases from 0 to 0.4,the hydrogen desorption capacity increases from 0.19% to 1.39% (mass fraction) in 20 min for the as-cast alloy,and from 0.89% to 2.18% (mass fraction) for the as-spun alloy (30 m/s).展开更多
The correlation between Si content （0.1%-0.5%, mass fraction） and pulse laser welding performance of AI-Mn-Mg aluminum alloy sheets was studied. The sheets were fabricated in the laboratory, with gauge of 0.45 mm, H...The correlation between Si content （0.1%-0.5%, mass fraction） and pulse laser welding performance of AI-Mn-Mg aluminum alloy sheets was studied. The sheets were fabricated in the laboratory, with gauge of 0.45 mm, H16 temper by pulse laser welding. It was found that no cracking existed in the welding pool as Si content was below 0.34%. However, when the Si content increased to 0.47%, cracking formed in the welding pool. Microstructure observations indicated that residual eutectic phases distributed at the grain boundaries were discontinuous and appeared to be small particles in lower Si content alloys; the residual eutectic phases distributed at the grain boundaries were partially continuous and appeared to be films in higher Si content alloys. These phenomena could explain why Si content adversely affected the laser welding performance.展开更多
Bulk metallic glasses (BMGs) with large supercooled liquid region are promising materials for superplastic forming. In this paper, we demonstrate a microstructure-based strategy to pinpoint the composition with the la...Bulk metallic glasses (BMGs) with large supercooled liquid region are promising materials for superplastic forming. In this paper, we demonstrate a microstructure-based strategy to pinpoint the composition with the largest supercooled liquid region in La 86 x Al 14 Cu x (x=16 at%-20 at%) metallic glass system. By monitoring the changes in crystallization behavior of the glassy alloys with composition to search for the alloys exhibiting eutectic crystallization, the glassy alloys with the largest supercooled liquid region in the given alloy system can be found. The metallic glasses with Cu contents of 16 at%-19 at% exhibited two crystallization peaks, and the primary crystallization product was identified to be α-La by means of DSC, XRD and TEM. The increase in Cu content resulted in the decay of the primary crystallization peak and the increase in onset temperature of crystallization, leading to the enlargement of supercooled liquid region. By further suppressing the α-La primary crystallization with increasing Cu content up to 20 at%, the eutectic crystallization of α-La and LaCu 13 through one crystallization reaction occurred upon heating, where the largest supercooled liquid region of 65 K for La 66 Al 14 Cu 20 glassy alloy was located. This study indicats that, in a given glassy alloy system, a larger supercooled liquid region can be achieved by optimizing the alloy compositions to suppress the primary crystallization.展开更多
基金Project(2006AA05Z132) supported by the National High-tech Research and Development Program of ChinaProjects(50871050, 50961009) supported by the National Natural Science Foundation of China+1 种基金Project(2010ZD05) supported by the Natural Science Foundation of Inner Mongolia, ChinaProject(NJzy08071) supported by the High Education Science Research Program of Inner Mongolia, China
文摘In order to improve the hydriding and dehydriding kinetics of the Mg2Ni-type alloys,Ni in the alloy is substituted by element Co. The nanocrystalline and amorphous Mg2Ni-type Mg2Ni1-xCox (x=0,0.1,0.2,0.3,0.4) alloys were synthesized by melt-spinning technique. The structures of the as-cast and spun alloys were studied with an X-ray diffractometer (XRD) and a high resolution transmission electronic microscope (HRTEM). An investigation on the thermal stability of the as-spun alloys was carried out with a differential scanning calorimeter (DSC). The hydrogen absorption and desorption kinetics of the alloys were measured with an automatically controlled Sieverts apparatus. The results demonstrate that the substitution of Co for Ni does not alter the major phase of Mg2Ni but results in the formation of secondary phase MgCo2. No amorphous phase is detected in the as-spun Co-free alloy,but a certain amount of amorphous phase is clearly found in the as-spun Co-containing alloys. The substitution of Co for Ni exerts a slight influence on the hydriding kinetics of the as-spun alloy. However,it dramatically enhances the dehydriding kinetics of the as-cast and spun alloys. As Co content (x) increases from 0 to 0.4,the hydrogen desorption capacity increases from 0.19% to 1.39% (mass fraction) in 20 min for the as-cast alloy,and from 0.89% to 2.18% (mass fraction) for the as-spun alloy (30 m/s).
基金Project(2011KJZD04)supported by the CHINALCO Science and Development Foundation,China
文摘The correlation between Si content （0.1%-0.5%, mass fraction） and pulse laser welding performance of AI-Mn-Mg aluminum alloy sheets was studied. The sheets were fabricated in the laboratory, with gauge of 0.45 mm, H16 temper by pulse laser welding. It was found that no cracking existed in the welding pool as Si content was below 0.34%. However, when the Si content increased to 0.47%, cracking formed in the welding pool. Microstructure observations indicated that residual eutectic phases distributed at the grain boundaries were discontinuous and appeared to be small particles in lower Si content alloys; the residual eutectic phases distributed at the grain boundaries were partially continuous and appeared to be films in higher Si content alloys. These phenomena could explain why Si content adversely affected the laser welding performance.
基金supported by the National Natural Science Foundation of China (Grant Nos. 50631010, 50771005 and 50771006)the National Basic Research Program of China (Grant No. 2007CB613900)
文摘Bulk metallic glasses (BMGs) with large supercooled liquid region are promising materials for superplastic forming. In this paper, we demonstrate a microstructure-based strategy to pinpoint the composition with the largest supercooled liquid region in La 86 x Al 14 Cu x (x=16 at%-20 at%) metallic glass system. By monitoring the changes in crystallization behavior of the glassy alloys with composition to search for the alloys exhibiting eutectic crystallization, the glassy alloys with the largest supercooled liquid region in the given alloy system can be found. The metallic glasses with Cu contents of 16 at%-19 at% exhibited two crystallization peaks, and the primary crystallization product was identified to be α-La by means of DSC, XRD and TEM. The increase in Cu content resulted in the decay of the primary crystallization peak and the increase in onset temperature of crystallization, leading to the enlargement of supercooled liquid region. By further suppressing the α-La primary crystallization with increasing Cu content up to 20 at%, the eutectic crystallization of α-La and LaCu 13 through one crystallization reaction occurred upon heating, where the largest supercooled liquid region of 65 K for La 66 Al 14 Cu 20 glassy alloy was located. This study indicats that, in a given glassy alloy system, a larger supercooled liquid region can be achieved by optimizing the alloy compositions to suppress the primary crystallization.
