汽车甩挂运输最佳运距的研究

汽车甩挂运输是先进的公路运输形式之一。从汽车甩挂运输生产工艺的全过程和尽量提高车时利用率出发,提出了适合我国目前推行汽车甩挂运输的最佳单程运距为53～100 km、133～220 km和293～460km。

变压器运行效率与最佳运行效率的计算

由于供电对象与负荷性质的差异,变压器运行中的输入、输出功率在不断地变化,变压器运行时的效率不是恒定不变的,因此,在选择变压器时,首先应了解供电对象和负荷运行特点,在求得变压器最佳运行效率的基础上,再综合考虑其它条件来正确选取变压器容量,本文介绍的变压器运行效率与最佳运行效率的计算对变压器的经济、节能运行具有实用参考价值。

RESEARCH ON OPTIMAL OPERATION OF WATER PRODUCING SYSTEM

Basing on a viewpoint of all sided water producing system,a comprehensive analysis of the operation status and the relationship between each working unit in water producing system,including coagulation,sedimentation and filtration etc.was made.By investigating the influence of backwashing consumption,the amount of sludge ejected from sedimentation tank and coagulant ratio upon the cost,the cost effective function of the system was presented.Afterwards,the solution was found out and the corresponding computer program was developed.When applied with real world data,it proved that this method significantly reduced the water producing cost.

气固喷射器的三维数值模拟

本文结合欧拉法和拉格朗日方法建立数学物理模型,利用CFD软件对气力输送气固喷射器进行了三维数值模拟,122重点研究了不同气速对喷射器内部流场的压力场、速度场和颗粒浓度场的分布。结果表明:气体进口速度越高,喷射器的1.450001压降越大;随着进口气速的增大颗粒浓度曲线逐渐平缓,颗粒的沉降逐渐减少,输运效果逐渐增强,但当气速增大到一定2.450001程度时,25m/s和30m/s的曲线基本重合,变化不大,在计算的范围内速度为25m/s时输运效率最好。

Optimal operation of water distribution networks under local pipe failures

The optimal operation of water distribution networks under local pipe failures, such as water main breaks, was proposed. Based on a hydraulic analysis and a simulation of water distribution networks, a macroscopic model for a network under a local pipe failure was established by the statistical regression. After the operation objectives under a local pipe failure were determined, the optimal operation model was developed and solved by the genetic algorithm. The program was developed and examined by a city distribution network. The optimal operation alternative shows that the electricity cost is saved approximately 11%, the income of the water corporation is increased approximately 5%, and the pressure in the water distribution network is distributed evenly to ensure the network safe operation. Therefore, the proposed method for optimal operation under local pipe failure is feasible and cost-effective.

A systematic approach for synthesizing a low-temperature distillation system

In this paper, by combining a stochastic optimization method with a refrigeration shaft work targeting method,an approach for the synthesis of a heat integrated complex distillation system in a low-temperature process is presented. The synthesis problem is formulated as a mixed-integer nonlinear programming(MINLP) problem,which is solved by simulated annealing algorithm under a random procedure to explore the optimal operating parameters and the distillation sequence structure. The shaft work targeting method is used to evaluate the minimum energy cost of the corresponding separation system during the optimization without any need for a detailed design for the heat exchanger network(HEN) and the refrigeration system(RS). The method presented in the paper can dramatically reduce the scale and complexity of the problem. A case study of ethylene cold-end separation is used to illustrate the application of the approach. Compared with the original industrial scheme, the result is encouraging.

Receiver Function Estimated by Wiener Filtering

Wiener filtering is used to estimate receiver function in a time_domain. With the vertical component of 3_component teleseismic P waveform as the input of a Wiener filter, receiver function as the filter response, and radial and tangential components as the expected output, receiver function is estimated by minimizing the error between expected and actual outputs. Receiver function can be obtained by solving the Toeplitz equation using the Levinson algorithm. The non_singularity of the Toeplitz equation ensures the stability of Wiener Deconvolution. Both synthetic and observational seismogram checks show that Wiener Deconvolution is an effective time_domain method to estimate receiver function from teleseismic P waveform.

Oxygen pressure acid leaching of Gacun complex Cu concentrates

The treatment of the Gacun complex Cu concentrate with high contents of Pb,Zn,Ag,etc by oxygen pressure acid leaching was studied.It is unusual that tetrahedrite,whose treatment was rarely studied,is the primary copper mineral of the concentrates.Most of silver also occurs in the mineral.The optimum operating parameters of oxygen pressure acid leaching were established by conditional tests.Pilot scale test was carried out under the parameters,and the leaching rates of copper and zinc are as high as 97.10% and 89.83% while lead and silver are transformed into sulfate and sulfide respectively and stay in leaching residue.The copper and zinc in lixivium were reclaimed by extraction-electrowinning and purification-electrowinning,respectively,and the lead and silver in the residue were reclaimed separately by chloride leaching and thiourea leaching.The extraction rate of copper achieves 96%,and the leaching rates of lead and silver reach 90% and 95%,respectively.

Concentration of Vinasse Using Membrane Filtration Processes

The application of single nanofiltration （NF） and sequential filtration of microfiltration （MF） and NF for the concentration of vinasse were studied. Filtration experiments were performed at 60 ℃, 500 rpm and different transmembrane pressures using four commercial membranes： MF, PVDF 0.2 μm; NF, PES 300, 500 and 1000 Da. The process effectiveness was evaluated through the permeate flux and the total solids （TS） concentration in the retentate. Because the retention of TS and permeate fluxes were very similar for MF, PVDF-0.2 membrane at 0.10 MPa was selected because of its lower power consumption. The best conditions tested for NF were the following： PES-1000 at 3.50 MPa with a flux of 183.2 kg/m^2 h at a volume reduction factor （VRF） of 2, under which 68% of solids were retained. For the MF ＋ NF, a PES-1000 at 3.50 MPa was selected because a higher permeate flux was achieved at a VRF of 4, and PES-500 at 3.50 MPa because a higher retention of TS was achieved compared to the other experiments. A single NF resulted in a retentate concentration that was almost twice as high as the hybrid MF and NF process, allowing reduced costs in its transportation from distilleries to distant areas.

Optimal trajectory planning for natural biped walking locomotion

An optimal trajectory planning method has been proposed for the walking locomotion of a biped mechanical system with thighs, shanks and small feet, which is modelled as a 3 DOF link system consisting of an inverted pendulum and a 2 DOF swing leg. The locomotion of swing and supporting legs is solved by the optimal trajectory planning based on function approximation. The optimal trajectory planning based on function approximation. The optimal walking locomotion solution with minimum square of input torque exhibits a natural walking gait with one step period of 0.64 s similar to the human walking gait by using the link parameters of an adult’s leg. It is concluded from the computation results that the method proposed in this paper has been proved to be an effective tool for solving the optimal walking locomotion and joint control torque problems for a 3 DOF biped mechanism; when the ankle joint of the supporting leg is a passive joint, a nearly, optimal walking solution can be obtained at t 1=0.49 s and t 2=10 s, and however, when the knee is a passive joint, it is impossible to obtain a solution which satisfies the constraint condition; for the link parameters used in this paper, the length of an optimal stride is 0.3 m.

Optimal design of V-type ultrasonic motor

V-type ultrasonic linear motor fabricated using a simple punching technique was proposed to utilize as an actuator of small precision machine.The stator of the motor is composed of a thin elastic body and four ceramics attached to the upper and bottom areas of the body.The ceramics have each direction of polarization.When two harmonic voltages with a 90° phase difference are applied to the ceramics,symmetric and anti-symmetric displacements will generate at the tip to produce an elliptical motion.A finite element analysis(ATILA) was conducted to simulate the motion pattern for the contact tip of the stator.To develop a model that generates the maximum displacement at contact tip,the FEM program was used for various lengths.In addition,an optimal model was chosen by considering the magnitude and shape of the displacement according to changes in frequency.The maximum elliptical displacement is shown by W2L11 model,which has a ratio of ceramic width to length of 1:5.5.However,the displacement of the contact tip is reduced by the bucking phenomenon if the ratio is larger than 1:6.

Application of Interval Newton Method to Solve Nonlinear Equations and Global Optimization

The basic principle of interval arithmetic and the basic algorithm of the interval Newton methods are introduced.The prototype algorithm can not find any zero in an interval that has zero sometimes,that is,it is instable.So the prototype relaxation procedure is improved in this paper.Additionally,an immediate test of the existence of a solution following branch_and_bound is proposed,which avoids unwanted computations in those intervals that have no solution.The numerical results demonstrat that the improved interval Newton method is superior to prototype algorithm in terms of solution quality,stability and convergent speed.

Process optimization study on the carbonylation of methyl acetate

Acetic anhydride is the important organic chemical raw material, and is used widely in chemical industry,pharmaceutical industry, dyes, spices and other fields. In this paper, the process of carbonylation of methyl acetate in rhodium iodine catalyst system was studied, and the suitable reaction conditions were determined.At the same time, the kinetic model was established. The optimum reaction conditions were as follows： the reaction pressure was 5 MPa, the hydrogen content was 8%, the amount of iodomethane was 15%, the amount of lithium iodide was 3%, the reaction temperature was 150 ℃ and the reaction time is 3 h. Under the above reaction conditions, the selectivity of the reaction is close to 100% and the conversion is as high as 92%. The macroscopic kinetic model of the reaction was established in the temperature range of 120 ℃–150 ℃. The reaction is an irreversible reaction without the formation of by-products and the dynamic equation is also given in the Conclusions section.

A Comparative Study on the Fixed Bed Pyrolysis of Different Biomass Solid Wastes

Biomass in the form of nutshell, hay of catkin, wheat straw and linseed residue in particles have been pyrolyzed in laboratory scale fixed bed reactor which yielded liquid oil, solid char and gas. The variation of oil yield for different biomass feedstock with reactor bed temperature and feed size is presented in this paper. A maximum liquid yield of 55 wt% of dry feedstock is obtained at an optimum temperature of 500℃ for a feed size of 300-600μm with a running time of 55 min for nutshell as the feedstock while the minimum liquid oil yield is found to be 30 wt% of feedstock at an optimum temperature of 400℃ for a feed size of 2.36 mm with a running time of 65 min for linseed residue as the feedstock. A comparison on the product yields is highlighted in this study. The pyrolysis liquid products are characterized and compared for some of the fuel properties like HHV （higher heating value）, viscosity, density and specific gravity.

公路甩挂物流运输组织模式的优化研究

甩挂运输是一种高效、集约、环保的公路运输组织形式,也是国家推行低碳交通的重要组织方式之一。本文通过最佳运输距离和最佳拖挂车比的理论分析,以及引入司机接驳运输模式,探讨了甩挂运输组织模式的优化方案。

Numerical Analysis of Chevron Nozzle Effects on Performance of the Supersonic Ejector-Diffuser System

The supersonic nozzle is the most important device of an ejector-diffuser system.The best operation condition and optimal structure of supersonic nozzle are hardly known due to the complicated turbulent mixing,compressibility effects and even flow unsteadiness which are generated around the nozzle extent.In the present study,the primary stream nozzle was redesigned using convergent nozzle to activate the shear actions between the primary and secondary streams,by means of longitudinal vortices generated between the Chevron lobes.Exactly same geometrical model of ejector-diffuser system was created to validate the results of experimental data.The operation characteristics of the ejector system were compared between Chevron nozzle and conventional convergent nozzle for the primary stream.A CFD method has been applied to simulate the supersonic flows and shock waves inside the ejector.It is observed that the flow structure and shock system were changed and primary numerical analysis results show that the Chevron nozzle achieve a positive effect on the supersonic ejector-diffuser system performance.The ejector with Chevron nozzle can entrain more secondary stream with less primary stream mass flow rate.

FORWARD-BACKWARD STOCHASTIC DIFFERENTIAL EQUATIONS, LINEAR QUADRATIC STOCHASTIC OPTIMAL CONTROL AND NONZERO SUM DIFFERENTIAL GAMES

In this paper, we use the solutions of forward-backward stochastic differential equations to get the explicit form of the optimal control for linear quadratic stochastic optimal control problem and the open-loop Nash equilibrium point for nonzero sum differential games problem. We also discuss the solvability of the generalized Riccati equation system and give the linear feedback regulator for the optimal control problem using the solution of this kind of Riccati equation system.

Best constants for Hausdorf operators on n-dimensional product spaces

In this paper, we study certain Hausdorff operators in the high-dimensional product spaces. We obtain their power weighted boundedness from Lp to Lq and characterize the necessary and sufficient conditions for their boundedness on the power weighted Lp spaces. Moreover, in the case p = q, we obtain the sharp bound constants.