The forming quality of high-strength TA18 titanium alloy tube during numerical control bending in changing bending angle β, relative bending radius R/D and tube sizes such as diameter D and wall thickness t was clari...The forming quality of high-strength TA18 titanium alloy tube during numerical control bending in changing bending angle β, relative bending radius R/D and tube sizes such as diameter D and wall thickness t was clarified by finite element simulation. The results show that the distribution of wall thickness change ratio Δt and cross section deformation ratio ΔD are very similar under different β; the Δt and ΔD decrease with the increase of R/D, and to obtain the qualified bent tube, the R/D must be greater than 2.0; the wall thinning ratio Δto slightly increases with larger D and t, while the wall thickening ratio Δti and ΔD increase with the larger D and smaller t; the Δto and ΔD firstly decrease and then increase, while the Δti increases, for the same D/t with the increase of D and t.展开更多
A two-dimensional numerical model is proposed to simulate the thermal discharge from a power plant in Jiangsu Province. The equations in the model consist of two-dimensional non-steady shallow water equations and ther...A two-dimensional numerical model is proposed to simulate the thermal discharge from a power plant in Jiangsu Province. The equations in the model consist of two-dimensional non-steady shallow water equations and thermal waste transport equations. Finite volume method （FVM） is used to discretize the shallow water equations, and flux difference splitting （FDS） scheme is applied. The calculated area with the same temperature increment shows the effect of thermal discharge on sea water. A comparison between simulated results and the experimental data shows good agreement. It indicates that this method can give high precision in the heat transfer simulation in coastal areas.展开更多
To characterize the elastic-plastic properties of thin film materials on elastic-plastic substrates,a simple theory model was proposed,which included three steps:dimensionless analysis,finite element modeling and data...To characterize the elastic-plastic properties of thin film materials on elastic-plastic substrates,a simple theory model was proposed,which included three steps:dimensionless analysis,finite element modeling and data fitting.The dimensionless analysis was applied to deriving two preliminary nondimensional relationships of the material properties,and finite element modeling and data fitting were carried out to establish their explicit forms.Numerical indentation tests were carried out to examine the effectiveness of the proposed model and the good agreement shows that the proposed theory model can be applied in practice.展开更多
基金Project(GJJ150810)supported by the Research Project of Science and Technology for Jiangxi Province Department of Education,ChinaProject(gf201501001)supported by National Defense Key Discipline Laboratory of Light Alloy Processing Science and Technology,Nanchang Hangkong University,ChinaProject(BSJJ2015015)supported by Doctor Start-up Fund of Jiangxi Science&Technology Normal University,China
文摘The forming quality of high-strength TA18 titanium alloy tube during numerical control bending in changing bending angle β, relative bending radius R/D and tube sizes such as diameter D and wall thickness t was clarified by finite element simulation. The results show that the distribution of wall thickness change ratio Δt and cross section deformation ratio ΔD are very similar under different β; the Δt and ΔD decrease with the increase of R/D, and to obtain the qualified bent tube, the R/D must be greater than 2.0; the wall thinning ratio Δto slightly increases with larger D and t, while the wall thickening ratio Δti and ΔD increase with the larger D and smaller t; the Δto and ΔD firstly decrease and then increase, while the Δti increases, for the same D/t with the increase of D and t.
文摘A two-dimensional numerical model is proposed to simulate the thermal discharge from a power plant in Jiangsu Province. The equations in the model consist of two-dimensional non-steady shallow water equations and thermal waste transport equations. Finite volume method （FVM） is used to discretize the shallow water equations, and flux difference splitting （FDS） scheme is applied. The calculated area with the same temperature increment shows the effect of thermal discharge on sea water. A comparison between simulated results and the experimental data shows good agreement. It indicates that this method can give high precision in the heat transfer simulation in coastal areas.
基金Projects(50531060,10525211,10828205)supported by the National Natural Science Foundation of ChinaProject(10525211)supported by National Science Found for Distinguished Young Scholars of ChinaProject(076044)supported by the Cultivation Fund of the Key Scientific and Technical Innovation Project,Ministry of Education of China
文摘To characterize the elastic-plastic properties of thin film materials on elastic-plastic substrates,a simple theory model was proposed,which included three steps:dimensionless analysis,finite element modeling and data fitting.The dimensionless analysis was applied to deriving two preliminary nondimensional relationships of the material properties,and finite element modeling and data fitting were carried out to establish their explicit forms.Numerical indentation tests were carried out to examine the effectiveness of the proposed model and the good agreement shows that the proposed theory model can be applied in practice.
