期刊文献+
共找到26篇文章
< 1 2 >
每页显示 20 50 100
漏斗型导流内构件对内循环三相流化床流体力学与传质特性的影响 被引量:16
1
作者 韦朝海 李磊 +2 位作者 吴锦华 吴超飞 吴景雄 《化工学报》 EI CAS CSCD 北大核心 2007年第3期591-595,共5页
The effects of funnel-shape internals on hydrodynamics and mass transfer in an internal loop three-phase fluidized bed were investigated.Three different kinds of internals were designed which were setup on the top of ... The effects of funnel-shape internals on hydrodynamics and mass transfer in an internal loop three-phase fluidized bed were investigated.Three different kinds of internals were designed which were setup on the top of draft-tube in terms of horizontal angle and outer diameter, and gas hold up, liquid mixing time, liquid circulation velocity and mass transfer coefficient were measured respectively.It was shown that the riser gas holdup and mass transfer coefficient increased by 10% and 15% than that without such an internal, liquid mixing time decreased by 10% to 25%.When the superficial gas velocity was less than 0.5 cm·s-1, liquid circulation velocity increased with the setup of such internals·Liquid circulation velocity decreased when the superficial gas velocity was above 0.5 cm·s-1.In addition, the variation of structural parameters of funnel-shape internals had significant effects on hydrodynamics and mass transfer. 展开更多
关键词 漏斗型导构件 内循环三相化床 体力学 传质
下载PDF
不同扰流内构件强化管式反应器传质性能的研究 被引量:1
2
作者 王芳 初广文 +3 位作者 邹海魁 向阳 罗勇 陈建峰 《北京化工大学学报(自然科学版)》 CAS CSCD 北大核心 2012年第6期1-5,共5页
采用NaOH-CO2-H2O体系,研究了4种不同扰流内构件及其组合型式对管式反应器传质性能的影响。以气相体积总传质系数KGaV作为衡量传质效果的评价指标,考察了液体流量L、气体流量G、不同扰流内构件及其组合型式对KGaV的影响。结果表明,KGaV... 采用NaOH-CO2-H2O体系,研究了4种不同扰流内构件及其组合型式对管式反应器传质性能的影响。以气相体积总传质系数KGaV作为衡量传质效果的评价指标,考察了液体流量L、气体流量G、不同扰流内构件及其组合型式对KGaV的影响。结果表明,KGaV随着液体流量增大而提高,气体流量的变化对KGaV的影响较小;中心扰流内构件和管壁扰流内构件的加入,有效地提高了管式反应器的KGaV;与空管相比,中心扰流内构件加入后管式反应器的KGaV提高了8%~47%,管壁扰流内构件加入后KGaV提高了15%~46%,中心与管壁组合扰流内构件加入后KGaV提高了19%~65%;通过比较4种扰流内构件对KGaV的影响可知,U型叶扇的传质强化效果最好,平面叶片的传质强化效果最差。 展开更多
关键词 传质强化 构件 管式反应器 气相体积总传质系数
下载PDF
折流内构件移动床中煤在不同停留时间下的热解行为特性 被引量:4
3
作者 周琦 张旭 +4 位作者 王岩 曲思建 张飏 白效言 裴贤丰 《燃料化学学报》 EI CAS CSCD 北大核心 2021年第5期703-711,共9页
针对常规移动床煤热解工艺所面临的无法处理粉煤,轻质焦油产率低、焦油品质差等问题,开发了折流内构件移动床热解工艺来调控气固两相的热质传递和热解反应过程。利用多段集气系统可及时地收集煤在不同热解阶段释放出的油气产物,研究了... 针对常规移动床煤热解工艺所面临的无法处理粉煤,轻质焦油产率低、焦油品质差等问题,开发了折流内构件移动床热解工艺来调控气固两相的热质传递和热解反应过程。利用多段集气系统可及时地收集煤在不同热解阶段释放出的油气产物,研究了淖毛湖煤在不同温度和停留时间下的热解行为特性和产物品质。结果表明,折流内构件强化了颗粒间的热量和挥发分物质的传递,使其可处理0.4−6.0 mm的粉煤;在热解温度550℃,停留时间为3.0 h时,热解焦油产率达到最高为11.38%(占格金焦油产率的86.87%,质量分数),焦油馏分中低于360℃的轻质组分质量分数为85.0%;随着停留时间的延长,热解气中的H2体积分数从22.1%增加到了35.1%,CO体积分数从8.0%增加到了9.5%;在第一和第二层反应器中的焦油产率随停留时间的延长而增加,在第三和第四层反应器内当停留时间为2.0 h时焦油产率最大;随着床层数的增加,焦油模拟蒸馏馏分中的轻质组分含量增加,焦油脂肪烃化合物含量减小,而单环芳烃和二环芳烃的含量逐渐增加。 展开更多
关键词 移动床 构件 热解 停留时间 焦油品质
下载PDF
折流内构件移动床新疆淖毛湖煤热解试验研究 被引量:2
4
作者 周琦 《煤炭学报》 EI CAS CSCD 北大核心 2021年第12期4054-4062,共9页
为了提取低阶煤中天然赋存的油气资源以获得高品质的焦油和煤气产品,并解决现有热解技术无法处理小粒径煤、焦油产率低、焦油品质差等技术瓶颈,提出了一种新型外热式折流内构件移动床热解工艺。以新疆淖毛湖煤为研究对象,考察了热解温... 为了提取低阶煤中天然赋存的油气资源以获得高品质的焦油和煤气产品,并解决现有热解技术无法处理小粒径煤、焦油产率低、焦油品质差等技术瓶颈,提出了一种新型外热式折流内构件移动床热解工艺。以新疆淖毛湖煤为研究对象,考察了热解温度、分段控温、多段集气等因素对热解产物分布和品质的影响,验证了新型反应器(折流内构件和多段集气系统)强化小粒径低阶煤热解反应的可行性和先进性。结果表明:折流内构件移动床热解工艺可以处理小粒径低阶煤;折流内构件可强化颗粒的运动,可显著提高颗粒的传热速率,当颗粒进入第2床层时(大约需要40 min)可达到目标温度,且整个试验过程的温度分布较稳定;淖毛湖煤在低温下热解所得焦油品质较差,焦油中的脂肪烃含量较高,适当提高温度会促进焦油的二次反应并有助于提高焦油的品质;通过建立逐渐升温的温度梯度可以提高焦油品质;多段集气系统确保了挥发分物质及时排出,并抑制了挥发分物质在高温下的二次裂解反应;对于粒径为0.4~6.0 mm的新疆淖毛湖煤,当进煤量为5.0 kg/h、停留时间为2.0 h、热解温度为550℃时,焦油产率最高为10.81%,占格金焦油产率的82.5%,焦油中沸点大于360℃的重质组分含量为15.0%,该条件下的焦油的产率及品质均较高;在折流内构件强化热解反应的同时,通过协同调控反应器温度和分段集气可有效提高焦油的产率和品质。 展开更多
关键词 煤热解 新疆淖毛湖煤 构件移动床 反应调控 焦油品质
下载PDF
湿法烟气脱硫系统均流构件结垢分析
5
作者 陈坤洋 郭婷婷 王海刚 《工业安全与环保》 2018年第9期5-8,4,共5页
某电厂湿法脱硫系统在连续运行过程中出现了均流构件结垢堵塞的问题,导致机组无法正常运行。根据取样分析结果和运行数据,此次均流构件结垢的主要成分为Ca SO4晶体。主要原因是脱硫浆液p H值较低(4.1~5.4),增大了Ca SO4析出的趋势,且浆... 某电厂湿法脱硫系统在连续运行过程中出现了均流构件结垢堵塞的问题,导致机组无法正常运行。根据取样分析结果和运行数据,此次均流构件结垢的主要成分为Ca SO4晶体。主要原因是脱硫浆液p H值较低(4.1~5.4),增大了Ca SO4析出的趋势,且浆液中Cl-质量浓度较高,甚至超过20 g/L的限值,加快了Ca SO4的结垢速率。在脱硫系统运行过程中,应首先按照系统安全稳定运行相关措施,保证浆液p H值在合理的区间之内,同时重点对浆液中Cl-加以控制,及时排放脱硫废水以降低Cl-浓度。 展开更多
关键词 湿法烟气脱硫 构件 结垢 CaSO 4 PH Cl^-
下载PDF
基于构件组装的专业图像网格编程环境
6
作者 耿晓琪 《软件导刊》 2011年第5期164-167,共4页
根据图像处理应用专业性的特点,设计了一种基于构件组装的专业图像网格编程环境CB-GRID(Compo-nent Based Grid System).CB-GRID与目前的网格编程环境相比具有用户易用性、专业性、编程方便、高效性。CB-GRID的易用性得益于其采用的构... 根据图像处理应用专业性的特点,设计了一种基于构件组装的专业图像网格编程环境CB-GRID(Compo-nent Based Grid System).CB-GRID与目前的网格编程环境相比具有用户易用性、专业性、编程方便、高效性。CB-GRID的易用性得益于其采用的构件技术、用户只需要把网格服务构件进行组装即可形成图像网格应用;提出了一种最小传输代价构件调度算法,有效地优化了网格应用程序的运行性能,提高了效率。运行并行案例程序结果表明,CB-GRID提供了一种构建高性能的图像处理平台的新思路。 展开更多
关键词 图像应用 网格 构件调度 关键构件流 资源共享
下载PDF
新型絮凝反应器工艺性能试验研究 被引量:5
7
作者 毛进 王璟 +3 位作者 张江涛 王正江 苏艳 柴紫仪 《热力发电》 CAS 北大核心 2010年第5期105-107,112,共4页
根据微涡旋絮凝机理设计出新型絮凝反应器。通过与传统网格絮凝反应器的对比试验,对新型絮凝反应器的絮凝效果进行分析,以确定最佳的反应器结构。试验结果表明,在同等条件下,新型絮凝反应器絮凝效果优于网格反应器,其对悬浊液处理效果稳... 根据微涡旋絮凝机理设计出新型絮凝反应器。通过与传统网格絮凝反应器的对比试验,对新型絮凝反应器的絮凝效果进行分析,以确定最佳的反应器结构。试验结果表明,在同等条件下,新型絮凝反应器絮凝效果优于网格反应器,其对悬浊液处理效果稳定,处理后出水静沉30min,上清液浊度均能达到3NTU以下。相对传统机械搅拌澄清工艺,新型絮凝反应器具有水力停留时间短、对流量变化适应性强、运行稳定等优点。 展开更多
关键词 微涡旋 絮凝 反应器 构件 悬浊液 浊度
下载PDF
基于RUP的统一变更管理 被引量:1
8
作者 彭德良 《科学技术与工程》 2007年第8期1762-1766,共5页
介绍了统一配置管理的相关概念,讨论了一种基于RUP的统一配置管理模型及其关键工件的变更管理。
关键词 软件配置管理 RUP 活动 基线 变更集 构件流
下载PDF
Degradation of pMOSFETs with Ultrathin Oxide andDifferent HALO Dose
9
作者 赵要 胡靖 +1 位作者 许铭真 谭长华 《Journal of Semiconductors》 EI CAS CSCD 北大核心 2004年第9期1097-1103,共7页
The effect of HALO dose on device parameter degradation of pMOSFET with 2.1nm o xide and 0.135μm channel length at hot carrier stress is analyzed.It is found that the degradation mechanism is not sensitive to HALO d... The effect of HALO dose on device parameter degradation of pMOSFET with 2.1nm o xide and 0.135μm channel length at hot carrier stress is analyzed.It is found that the degradation mechanism is not sensitive to HALO dose changing,but the d egradation quantities of linear drain current,saturation drain current,and maxim um transconductance increase with HALO dose enhancing and are larger than those of speculated before.The degradation of device parameters (linear drain current, saturation drain current,and maximum transconductance) is attributed to not onl y the drain series resistance enhancing induced by interface states under spacer oxide and carrier mobility degradation but also the threshold voltage variation and initial threshold voltage increasing with HALO dose enhancing. 展开更多
关键词 hot carrier PMOSFET HALO DEGRADATION
下载PDF
Hydrodynamics and Solids Mixing Behavior in a Riser with Blunt Internals 被引量:3
10
作者 刘会娥 魏飞 +1 位作者 杨艳辉 金涌 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2003年第4期371-376,共6页
The hydrodynamics and solids mixing behavior in a riser with blunt internals are studied. A uniform radial distribution for solids fraction and particle velocity achieves near the internals. The turbulent velocity of ... The hydrodynamics and solids mixing behavior in a riser with blunt internals are studied. A uniform radial distribution for solids fraction and particle velocity achieves near the internals. The turbulent velocity of particles near the wall increases with the addition of the internals, with the lateral solids mixing enhanced significantly. Probability density distribution of particle velocity is bimodal in the riser with internals, which is similar to that in the conventional riser, indicating that no significant difference in the micro flow structure exists between the riser with internals and the conventional riser. At the same time, the axial solids mixing behavior changes insignificantly with the addition of internals. These results indicate that the micro flow structure in the riser is very stable, which changes insignificantly with the change of the bed structure. 展开更多
关键词 RISER internal HYDRODYNAMICS SOLIDS mixing behavior
下载PDF
Hydrodynamics and Lateral Gas Dispersion in a High-Density Circulating Fluidized Bed Reactor with Bluff Internals 被引量:3
11
作者 杨艳辉 贾新莉 +1 位作者 魏飞 金涌 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2001年第3期291-296,共6页
Effect of bluff internals on the hydrodynamics and lateral gas mixing was studied in a 0.186m ID high-density riser. With the bluff internals, the extremely non-uniform radial profiles of solid fraction and particle v... Effect of bluff internals on the hydrodynamics and lateral gas mixing was studied in a 0.186m ID high-density riser. With the bluff internals, the extremely non-uniform radial profiles of solid fraction and particle velocity become flat and the dense downflow layer near the wall disappears, indicating the significant enhancement of solid turbulence introduced by the internals. The fluctuation velocity and solid fraction transient signal analysis indicates a significant increase in fluctuation intensity near the wall region. The length influenced by the internals on the flow structure is about 1 meter. The lateral gas dispersion coefficient increases significantly as the bluff internals exist in the riser. 展开更多
关键词 high-density riser bluff internal solid fraction particle velocity transient analysis gas mixing gas dispersion model
下载PDF
近期国内中文报刊重要科技文章篇目辑览
12
《科技导报》 CAS CSCD 2007年第10期76-76,共1页
关键词 银离子选择性电极 中文报刊 频率适应性起搏器 漏斗型导构件 文章篇目
下载PDF
Refrigerant Distribution Characteristics in Vertical Header of Flat-Tube Heat Exchanger without Internal Protrusion
13
作者 Kazuhiro Endoh 《Journal of Energy and Power Engineering》 2017年第10期655-664,共10页
A heat exchanger that arranges flat tubes horizontally has a vertical header that distributes the refrigerant to each tube. When the heat exchanger works as an evaporator, differences in flow conditions at each branch... A heat exchanger that arranges flat tubes horizontally has a vertical header that distributes the refrigerant to each tube. When the heat exchanger works as an evaporator, differences in flow conditions at each branch, such as the ratio and distribution of vapor and liquid, due to the differences in densities and momentums of vapor and liquid in the two-phase flow make equal distribution difficult. This paper describes the distribution characteristics of a four-branch header that has a rectangular cross-section without the internal protrusion of flat tubes in the case of the inflow of the refrigerant R32 from the bottom of the header by using an equipment that can estimate the distribution ratio of the liquid and vapor phase to each branch. This paper also discusses the distribution characteristics on the basis of the flow visualization in the header. The flow visualization shows that a liquid level that contains vapor phase exists in the header and affects the distribution greatly. 展开更多
关键词 Refrigerant distribution vapor-liquid two-phase flow HEADER flat tube heat exchanger.
下载PDF
Hydrodynamic parameters in a flood impacted boulder block ramp: Krzczonówka mountain stream, Polish Carpathians 被引量:1
14
作者 RADECKI-PAWLIK Artur PLESINSKI Karol +2 位作者 RADECKI-PAWLIK Bartosz KUBON Piotr MANSON Russell 《Journal of Mountain Science》 SCIE CSCD 2018年第11期2335-2346,共12页
Boulder block ramps are river engineering structures used to stabilise river beds. Block ramps provide a semi-natural and aesthetically pleasing solution to certain river engineering problems in mountain streams. When... Boulder block ramps are river engineering structures used to stabilise river beds. Block ramps provide a semi-natural and aesthetically pleasing solution to certain river engineering problems in mountain streams. When constructing block ramps,one can use the dissipative behaviour of large macroroughness elements randomly placed on the river bed to enhance fish migration in an upstream direction thus, in this sense, meeting the requirements of the EU Water Framework Directive. Block ramps are often designed and constructed to replace damaged drop hydraulic structures in the channels of mountain streams. This paper investigates the resilience of a particular block ramp placed in the Krzczonówka stream(Polish Carpathians) in terms of the engineering design function and its durability against damaging. A hydrodynamic analysis of a block ramp is presented before and after a flood event that changed the configuration of the blocks. The seminatural unstructured hydraulic structure was built on the Krzczonowka stream to protect gas pipes which are located beneath it. As a result of several floods, the boulder block chute described in this paper was damaged, and some boulders were dislodged and transported downstream. Our post-flood investigations of bathymetry and velocity revealed that even damaged boulder blocks, removed from the chute and displaced downstream of the structure, still provide significant energy dissipation of the flowing water. The novel of our paper is for the first time showing very detailed analysis of unstructured block ramp hydrodynamics parameters done in the field.Also the novel finding of our investigations shows that before and after the flood event the unstructured block ramp structure, is still fish friendly in terms of hydrodynamics. 展开更多
关键词 Boulder ramp Mountain stream Hydrodynamic Ramp chute
下载PDF
Genre analysis on business English correspondence
15
作者 WANG Ji-yu 《Sino-US English Teaching》 2007年第12期42-46,56,共6页
This thesis has collected 156 business letters and analyzed their characteristics within the framework of V. K. Bhatia's cognitive structuring model. Each kind of the business letters follows different moves and with... This thesis has collected 156 business letters and analyzed their characteristics within the framework of V. K. Bhatia's cognitive structuring model. Each kind of the business letters follows different moves and within moves, a wide range of strategies are employed. This paper on the one hand illustrates the different structures of business letters and on the other hand demonstrates that the sequencing of the moves enjoys a great flexibility, which to some degree reflects the dynamic nature of genre. 展开更多
关键词 GENRE cognitive structure MOVE STRATEGY business correspondence
下载PDF
Numerical study of homogeneous–heterogeneous reactions on stagnation point flow of ferrofluid with non-linear slip condition
16
作者 Zaheer Abbas Mariam Sheikh 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2017年第1期11-17,共7页
This study deals with the stagnation point flow of ferrofluid over a flat plate with non-linear slip boundary condition in the presence of homogeneous-heterogeneous reactions.Three kinds of ferroparticles,namely,magne... This study deals with the stagnation point flow of ferrofluid over a flat plate with non-linear slip boundary condition in the presence of homogeneous-heterogeneous reactions.Three kinds of ferroparticles,namely,magnetite(Fe_3O_4),cobalt ferrite(CoFe_2O_4) and manganese zinc ferrite(Mn-ZnFe_2O_4) are taken into account with water and kerosene as conventional base fluids.The developed model of homogeneous-heterogeneous reactions in boundary layer flow with equal and unequal diffusivities for reactant and autocatalysis is considered.The governing partial differential equations are converted into system of non-linear ordinary differential equations by mean of similarity transformations.These ordinary differential equations are integrated numerically using shooting method.The effects of pertinent parameters on velocity and concentration profiles are presented graphically and discussed.We found that in the presence of Fe_3O_4-kerosene and CoFe_2O_4-kerosene,velocity profiles increase for large values of α and β whereas there is a decrement in concentration profiles with increasing values of if and K_s.Furthermore,the comparison between non-magnetic(A1_2O_3) and magnetic Fe_3O_4 nanoparticles is given in tabular form. 展开更多
关键词 Ferrofluid Stagnation point flow Homogeneous-heterogeneous reactions Generalized slip boundary condition Numerical solution
下载PDF
Hot compression deformation characteristics of Mg-Mn alloys
17
作者 方超 张静 +3 位作者 廖爱林 薛绍展 袁付庆 潘复生 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2010年第10期1841-1845,共5页
The hot deformation behaviors of solution treated Mg-1.8Mn-0.4Er-0.2Al alloys were investigated by means of compression tests on Gleeble-1500 in strain rate range of 0.01-10s-1,deformation temperature range of 250-450... The hot deformation behaviors of solution treated Mg-1.8Mn-0.4Er-0.2Al alloys were investigated by means of compression tests on Gleeble-1500 in strain rate range of 0.01-10s-1,deformation temperature range of 250-450℃ and a true strain of 0.6.The constitutive relationships among flow stress,strain rate and deformation temperature were described by Arrhenius-type equations,based on the fact that the material constants could be calculated under a wide range of strains.The results show that the flow stress of the experimental alloy decreases with temperature increasing and strain rate decreasing.Under the experimental conditions,the products of constant α and n in the constitutive equation are stable within certain strains,and the deformation activation energy ranges from 160 to 220 kJ/mol.It is proved that the values of calculated flow stress are close to the experimental results with average error of 2.01%. 展开更多
关键词 magnesium alloy thermal deformation flow stress constitutive equation
下载PDF
Software/Hardware Integrating Model of Embedded Reconfigurable Computing System for Digital Signal Processing
18
作者 刘守山 张同军 +1 位作者 毕丽君 陶安利 《Journal of Measurement Science and Instrumentation》 CAS 2010年第4期343-348,共6页
The system model of embedded reconfigurable system is discussed firstly, followed by the construction of the soft- ware and hardware platform. Based on the platform, the function trait and control models of digital si... The system model of embedded reconfigurable system is discussed firstly, followed by the construction of the soft- ware and hardware platform. Based on the platform, the function trait and control models of digital signal processing tasks are described. According the functional unit model and control model, a software/hardware integrating model with dataflow control infrastructure is constructed. The software/hardware partition is carded out in the experiments of ultrasonic signal processing, and the results show that the system model is practicable. 展开更多
关键词 RECONFIGURABLE embedded system digital signal prooessing integrating model function unit
下载PDF
水力桨隔板絮凝反应器工艺性能试验研究 被引量:2
19
作者 范文飙 李伟光 +2 位作者 公绪金 孙云凯 南军 《中国给水排水》 CAS CSCD 北大核心 2015年第19期99-103,共5页
基于微涡旋絮凝理论,开发出了利用水流动能自驱动的水力桨隔板絮凝反应器,并对比研究了其与传统网格絮凝反应器的絮凝沉淀效能,确定了水力桨隔板絮凝反应器的最佳结构和运行参数。结果表明:在同等条件下,水力桨隔板絮凝反应器的絮凝效... 基于微涡旋絮凝理论,开发出了利用水流动能自驱动的水力桨隔板絮凝反应器,并对比研究了其与传统网格絮凝反应器的絮凝沉淀效能,确定了水力桨隔板絮凝反应器的最佳结构和运行参数。结果表明:在同等条件下,水力桨隔板絮凝反应器的絮凝效果和稳定性均优于传统网格反应器,在最佳条件下,上清液浊度可达到3.0 NTU以下,水头损失较传统网格反应器降低40%以上。水力桨隔板絮凝反应器具有水力停留时间短、能耗低、抗冲击负荷能力强等优点,为净水厂升级改造提供了技术与理论支撑。 展开更多
关键词 水力桨隔板絮凝 微涡旋 构件 浊度
原文传递
Research on Component Law of Chinese Patent Medicine for Anti-influenza and Development of New Recipes for Anti-influenza by Unsupervised Data Mining Methods 被引量:17
20
作者 唐仕欢 陈建新 +6 位作者 李耿 吴宏伟 陈畅 张娜 高娜 杨洪军 黄璐琦 《Journal of Traditional Chinese Medicine》 SCIE CAS CSCD 2010年第4期288-293,共6页
Objective:To analyze the component law of Chinese patent medicines for anti-influenza and develop new prescriptions for anti-influenza by unsupervised data mining methods. Methods: Chinese patent medicine recipes for ... Objective:To analyze the component law of Chinese patent medicines for anti-influenza and develop new prescriptions for anti-influenza by unsupervised data mining methods. Methods: Chinese patent medicine recipes for anti-influenza were collected and recorded in the database, and then the correlation coefficient between herbs, core combinations of herbs and new prescriptions were analyzed by using modified mutual information, complex system entropy cluster and unsupervised hierarchical clustering, respectively. Results: Based on analysis of 126 Chinese patent medicine recipes, the frequency of each herb occurrence in these recipes, 54 frequently-used herb pairs, 34 core combinations were determined, and 4 new recipes for influenza were developed. Conclusion: Unsupervised data mining methods are able to mine the component law quickly and develop new prescriptions. 展开更多
关键词 INFLUENZA unsupervised data mining methods swine influenza new prescription discovery
原文传递
上一页 1 2 下一页 到第
使用帮助 返回顶部