论事物的析构性

作为整体或系统看待的事物都是可以解析和重新融构的 ,都具有析构性。析构性是事物基本的属性之一 ,把握事物的析构性有助于对事物整体形成科学的认识。通过对事物析构度的认识我们能够更好地把握事物的析构性。

Increasing the toughness while reducing the viscosity of carbon nanotube/ polyether imide/polyether ether ketone nanocomposites

Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether imide(PEI)were pre-pared by a direct wet powder blending method using a vertical injection molding machine.The addition of an optimum amount of PEI lowered the viscosity of the molten PEEK by approximately 50%while producing an increase in the toughness of the nanocom-posites,whose strain to failure increased by 129%,and fracture energy increased by 97%.The uniformly dispersed CNT/PEI powder reduced the processing difficulty of PEEK nanocomposites without affecting the thermal resistance.This improvement of the strength and viscosity of PEEK facilitate its use in the preparation of thermoplastic composites.

Mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with diameter of 160 mm

The mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with a diameter of 160 mm manufactured by ＂multi-direction forging（MDF） ＋ extrusion ＋ online cooling＂ technique were investigated by optical microscopy（OM）, scanning electron microscopy（SEM）, X-ray diffraction macro-texture measurement and room temperature（RT） tensile test. The results show that mixed grain structure is caused by the micro-segregation of Al in semi-continuous casting ingot. Homogenization of（380 °C, 8 h） ＋（410 °C, 12 h） cannot totally eliminate such micro-segregation. During MDF and extrusion, the dendrite interiors with 3%-4% Al（mass fraction） transform to fine grain zones, yet the dendrite edges with about 6% Al transform to coarse grain zones. XRD macro-textures of the outer, R/2 and center show typical fiber texture characteristics and the intensity of [0001]//Ra D orientation in the outer（11.245） is about twice as big as those in the R/2（6.026） and center（6.979）. The as-extruded AZ40 magnesium alloy bar has high elongation（A） and moderate ultimate tensile strength（Rm） in both extrusion direction（ED） and radius direction（Ra D）, i.e., A of 19%-25% and Rm of 256-264 MPa; however, yield strength（Rp0.2） shows anisotropy and heterogeneity, i.e., 103 MPa in Ra D, 137 MPa in ED-C（the center） and 161 MPa in ED-O（the outer）, which are mainly caused by the texture.（155 °C, 7 h） ＋（170 °C, 24 h） aging has no influence on strength and elongation of AZ40 magnesium bar.

An Experimental Analysis of Water and Soil Conservation Effected by Micro-landscape Structure

[Objective] This comparative experiment was to explore the soil loss con- trol effects under cultivation combination of different soil and vegetation types, and to provide scientific basis for the upcoming pilot project of ecological recovery. [Method] Both the rudiment of water locomotion functioned by micro-landscape structures and different spatial combinations of various landscape constituents are considered, thus, the combination of multi-soil type, crop species and site conditions is designed in three different experimental sites. [Result] Soil loss estimates in experiments in South Wello significantly depended on various soil type, slope, vegetation and type of con- servation structure; grass cover tremendously reduces soil loss; legume cultivation performed better than cereal cultivation in soil loss control. [Conclusion] By conduct- ing the data analysis of the experiment, a scientific reference is proposed to the agri- culture planting and protective mode for the alleviation of water and soil loss in Amhara Region, Ethiopia.

Effect of CuO and SnO_(2) particle size on hot extrusion deformation of AgCuOSnO_(2):Finite element simulation and experimental study

The finite element model is established according to the experimental results,and then the experimental results are verified by simulation calculation.In terms of the combination of finite element analysis and experiment,the effect of particle size of CuO and SnO_(2) on the stress,strain and microstructure of AgCuOSnO_(2) composite during hot extrusion was studied.The results illustrate that with the decrease of particle size,the dispersion of the second phase increases gradually,while the possibility of“tail shrinkage”of the billet decreases continuously;cubic CuO will evolve to fibrosis,and the degree of fibrosis will increase with the decrease of the particle size and ring clusters.Specifically,the degree of fibrosis at the middle end of the billet is higher than that at the front end,the degree of fibrosis at the front end is higher than that at the back end,and the degree of fibrosis on the surface is higher than that in the core;part of CuO fibers will bend,and the degree of buckling strength is positively correlated with the size of particles and their annular clusters.Additionally,there is fiber CuO in the front and back end of the billet that are inconsistent with the extrusion direction,and the degree of difference was negatively correlated with the particle size.

Effect of quenching rate on microstructure and mechanical properties of commercial AA7108 aluminium alloy

A commercial AA7108 aluminium alloy subjected to different quenching procedures from the solid solution temperature of 480 ℃ was considered. Both continuously cooling and quenching to intermediate temperatures （400, 300 and 200 ℃） followed by different holding times were applied. All the materials were subsequently subjected to the same industrial two-step artificial ageing procedure to obtain a maximum strength （T6）. Tensile testing of the different quenched materials in the T6 temper reveals a large deviation in strength dependent on the cooling/holding time, compared with the reference sample. A collection of the different quenched materials was chosen for further investigation of the precipitate structure by transmission electron microscopy （TEM） to explain the differences in mechanical properties.

Dynamic regimes of cemented backfill at early-age

In view of the mechanics characteristic of cemented tailings backfill(CTB)at early age,the separation Hopkinson pressure bar test device was used to explore the effects of curing age and impact energy.A total of 48 CTB samples with diameter of 50 mm and length of 25 mm were prepared with curing ages of 3,5,7 and 9 d.Impact tests under different impact energy(10,20,30 and 40 J)were carried out.The microstructure of CTB at different ages was analyzed by scanning electron microscopy(SEM).The results show that,the curing age mainly affects the mechanical properties and internal structure of early-age CTB.With increasing curing age,the mechanical properties of early-age CTB change from viscoelasticity to brittleness.The impact energy mainly affects the response of dynamic peak compressive strength to strain rate.Under low strain rate,the structure of CTB is broken,but still has bearing capacity,affecting the formation of later strength.It is concluded that the structural loses completely under the action of high strain rate.Therefore,the control of impact energy and the protection of curing age should be fully considered in actual production process.

Evolution of microstructure in semi-solid slurries of rheocast aluminum alloy

Semi-solid metal processing is being developed in die casting applications to give several cost benefits. To efficiently apply this emerging technology, it is important to understand the evolution of microstructure in semi-solid slurries for the control of the theological behavior in semi-solid state. An experimental apparatus was developed which can capture the grain structure at different times at early stages to understand how the semi-solid structure evolves. In this technique, semi-solid slurry was produced by injecting fine gas bubbles into the melt through a graphite diffuser during solidification. Then, a copper quenching mold was used to draw some semi-solid slurry into a thin channel. The semi-solid slurry was then rapidly frozen in the channel giving the microstructure of the slurry at the desired time. Samples of semi-solid 356 aluminum alloy were taken at different gas injection times of 1, 5, 10, 15, 20, 30, 35, 40, and 45 s. Analysis of the microstructure suggests that the fragmentation by remelting mechanism should be responsible for the formation of globular structure in this rheocasting process.

Seventy Years’“Micropedology”1938-2008:The Past and Future

Although the first microscopic observations on soils date already from the beginning of the twentieth century, the publication of Kubiena＇s book ＂Micropedology＂ in 1937 is considered as the beginning of this new scientific discipline. This first system for micromorphological descriptions of soils is considered as morphoanalytical, analysing the fabric according to pure morphological criteria. In a second period Kuniena used a morphogenetic approach, directly relating the global observed fabric to genetic soil horizons. This system, mainly limited to European soils, was in general use till the early nineteen-seventies. End of the nineteen-fifties non- genetic soil classification systems were developed （e.g. USDA）. This trend prompted R. Brewer to publish in 1964 a new morphoanalytical system for fabric analysis, used till the end of last century. Because of some inconsistencies in this approach, a working group of the ISSS published in 1985 a new set of morphoanalytical concepts and associated terminology （Bullock et al.）, in 2003 adapted and extended by Stoops. Several morphosynthetic systems, expressing a complete soil microfabric in a single （compound） term have been proposed, but none was really successful. In 1967 Kubiena introduced the term ＂micromorphometry＂ to name a new branch of micromorphology quantifying the soil fabric, mainly evaluating changes in porosity and structure resulting from soil management. The necessity of dearly defined concepts and terms for fabric analysis of soils and regoliths, even as a need for standardisation of quantitative methods, are discussed in the conclusions.

Intergranular Corrosion of UNS S31803 Heat Treated at 800 ℃ Varying Range Times

The aim of this work is evaluate the intergranular corrosion on UNS S31803 steel, with heat treatments at 800 ℃, varying treatment times of 30 mins, 360 mins and 1,440 mins. The results confirm the formation of o phases and secondary austenite （γ2）. For the analysis of the influence of o and γ2 phases, metallographic analysis were conducted through optical microscopy, potentiokinetic reactivation electrochemical techniques and potentiodynamic polarization in NaCI 3.5% solution. Microstructural analysis has shown a formation of γ2 and o phase in heat treatment, due to diffusion of chromium and molybdenum from δ phase to y phase, precipitating on δ/γ and δ/δ interfaces. The DL-EPR （Double loop electrochemical potentiokinetic reactivation） results have shown an increase of the DOS （degree of sensitization） for long periods of time on heat treatment. The results of potentiodynamic polarization showed a reduction of the corrosion and pitting potentials, followed by an increase of the current density when the UNS S31830 steel is heat treated during long periods of time.

Microstructure Analysis for Chemical Interaction between Cesium and SUS316 Steel in Fast Breeder Reactor Application

The objective of this study is to presume cesium corrosion process and its dominant factors in SUS316 steel, a fuel cladding material for fast breeder reactor application, based on both experimental results of cesium corrosion out-pile test and thermodynamic consideration. The cesium corrosion test was performed in simulated environment of high burn-up fuel pin. And main corrosion products in the specimen after the corrosion test were specified by TEM （transition electron microscopy） and SEM （scanning electron microscopy） in order to formulate a hypothesis of the cesium corrosion process. At the end of this study, it was found that the dominant factors of the corrosion process are the amount of cesium on the surface of the specimen, chromium content in the alloy, the supply rate of oxygen and temperature.

Microstructure analysis of deep rock in Meilinmiao Mine

SEM tests were conducted on four kinds of typical deep rocks in Meilinmiao Mine, and the micro properties were analyzed. The particles of gritstone are unbroken and particle diameter ranges from 80 lam to 400 pro, and the void between particles is wide. The macroscopic failure of gritstone is caused by breakage of the dung distributed between particles, and po- tassium feldspars contained in gritstone are not leached. The failure of medium sandstone is caused by micro cracks distributed in sandstone particles, and potassium feldspars are leached seriously, so the pores penetrate each other and there is close hy- draulic connection in medium sandstone. The particles of fine sandstone are broken, and the particle diameters range from 60 pm to 300 pm, which determines the pores have good connectivity between particles. The dolomites contained in fine sand- stone are corroded, and the micro fracture form belongs to inter-granular fracture. There are no particles and blocks in micro- structure of sandy mudstone, but there are diverse micro cracks. The failure of mudstone arises from the extension of micro cracks, and the microstructure is different from the other three kinds of sandstones obviously.

Microstructure and mechanical behavior of Ti/Cu/Ti laminated composites produced by corrugated and flat rolling

Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron microscopy, numerical simulation methods, peel and tensile examinations. The effect of CR and FR was comparatively analyzed. The results showed that the CR and FR laminated composites exhibited different effective plastic strain distributions of the Ti layer and Cu layer at the interface. The recrystallization texture, prismatic texture and pyramidal texture were developed in the Ti layer by CR, while the R-Goss texture and shear texture were developed in the Cu layer by CR. The typical deformation texture components were developed in the Ti layer and Cu layer of FR laminated composites. The CR laminated composites had higher bond strength, tensile strength and ductility.

Microstructure-Fatigue Crack Propagation Kinetics Relationships of Rail Steels

Microstructural analysis and fatigue crack propagation behavior of three types of rail steels, was performed. These are premium pearlitic, austenitic manganese （AM） and bainitic rail steels. Rectangular un-notched and notched test specimens were machined from railheads of each material using electrical discharge machining （EDM） and used for the mechanical properties and fatigue evaluation respectively. Bainitic steel has the highest yield strength, ultimate strength, and strain to failure as compared to both pearlitic and austenitic manganese steels. Fatigue studies showed that the crack speed for the bainitic steel is lower than that for the pearlitie and the AM steels over the entire range of the energy release rate. The bainitic steel exhibits a higher rate of crack deceleration in the second stage, as indicated by the lower slope of the fatigue crack propagation kinetics curve in comparison with the pearlitic and manganese rail steels. This attests to the superior fatigue damage tolerance of the bainitic rail steel in comparison to pearlitic and austenitic manganese rail steels. Microstructural analysis of the three rail steels revealed that bainitic steel has a more intricate structure than AM and pearlitic steels. AM steel shows very few signs of being work hardened or toughened, which usually increases the mechanical properties of the material. As the number of alloying elements increase, the microstructure of the steel becomes more complex, resulting in the increase of mechanical properties and fatigue fracture resistance of bainitic rail steel.

Properties of CNTs/MoSi2 composites prepared by spark plasma sintering

Molybdenum disilicide(MoSi_2) based composites with various contents of carbon nanotubes(CNTs) were fabricated by spark plasma sintering(SPS) in vacuum under a pressure of 25 MPa.The composites obtained under a sintering temperature of 1500 °C and time of 10 min exhibited optimum mechanical properties at room temperature in terms of fracture toughness and transverse rupture strength.MoSi_2 based composite with 6.0% CNTs(volume fraction) had the highest fracture toughness,transverse rupture strength and hardness,which were improved by about 25.7%,51.5% and 24.4% respectively,as compared with pure MoSi_2.A Mo_(4.8)Si_3C_(0.6) phase was detected in CNTs/MoSi_2 composites by both X-ray diffraction(XRD) method and microstructure analysis with scanning electron microscopy(SEM).It is believed that the fine grains and well dispersed small Mo_(4.8)Si_3C_(0.6) particles had led to a higher hardness and strength of CNTs/MoSi_2 composites because of their particle pullout,crack deflection and micro-bridging effects.

New Activity of the Tanlu Fault Zone in the South of Huaihe to the Nvshanhu Segment since the Late Quaternary

Taking the Huaihe to the Nvshanhu segment of the Tanlu( Tancheng-Lujiang) fault zone as the main research target to explore whether there has been new activity since the late Quaternary,and based on the interpretation of remote sensing images and repeated surface investigations,we excavated trenches at the sections where the tectonic landform is significant,identified and recorded the deformation patterns of the fault and analyzed the activity behavior. Samples of new activity and deformation were collected and oriented slices were ground based on the samples ' original state to make the micro structural analysis and demonstration. All of the above research shows very clear linear tectonic geomorphology along the fault,three trenches across the fault zone all revealed new deformation traces since late Quaternary. The latest stratum dislocated by the fault is the late Quaternary and Holocene. The main slip mode is stick slip,as represented typically by fault scarps,wedge accumulation,the faults and the filled cracks and so on. In general,it shows the characteristics of brittle high-speed deformation and belongs to the prehistoric earthquake ruins. The above understanding was confirmed partially by microscopic analysis. In addition,the similarities and differences and the possible reasons for the characteristics of the latest activities of the Tancheng-Lujiang fault zone in the north and south of the Huaihe River regions are also discussed in this paper.

Evolution of the ductile shear zone of the Paishanlou gold deposits,western Liaoning,China

The combination of field surveys with analysis of microstructure of tectonite and Electron Backscatter Diffraction(EBSD) on quartz fabric indicated that three periods of ductile shear events developed in the Paishanlou gold deposits and the E-W and NE-striking ductile shear zones were formed during each event.The E-W-striking ductile shear zone,accompanied by compressional and dextral shear slip,was shear-cut by the NE-striking shear zones,accompanied by compressional-sinistral shear slip and sinistral-normal shear slip,successively.An E-W-striking ductile shear zone developed at a deeper tectonic level and at middle- to high-temperatures,accompanied by abundant microstructures,including microlayering between a polycrystal quartz belt and mica,and quartz deformation was depended on cylinder(10-10) or <c> glide.The development of an E-W-striking shear zone can be seen as a tectonic pattern in the region of the Paishanlou gold deposits of the collision between the Mongolian tectonic belt and the North Archean Craton from Suolun to the Linxi suture zone during the Indosinian.The NE-striking ductile shear zone developed approximately 160 Ma during the early Yianshanian at middle to shallow tectonic levels and at middle- to low-temperatures,accompanied by typical microstructures,including polycrystal quartz aggregation and quartz subgrain rotation recrystallization,etc.,and quartz deformation was depended on prismatic(1011) glide.The last ductile shear event around the NE-striking shear zone developed at low temperatures and shallow tectonic levels,yielding to a pre-existing NE-striking shear zone,accompanied by abundant microstructures,including low-temperature quartz grain boundary migration and bulging recrystallization.The last ductile shear movement may be related to lithosphere thinning and the destruction of the North China Craton from approximately 130-120 Ma,and this shear event resulted directly in the mineralization in the Paishanlou region.

Impact of the next-generation sequencing data depth on various biological result inferences

Next-generation sequencing(NGS) technologies have revolutionized the field of genomics and provided unprecedented opportunities for high-throughput analysis at the levels of genomics,transcriptomics and epigenetics.However,the cost of NGS is still prohibitive for many laboratories.It is imperative to address the trade-off between the sequencing depth and cost.In this review,we will discuss the effects of sequencing depth on the detection of genes,quantification of gene expression and discovering of gene structural variants.This will provide readers information on choosing appropriate sequencing depth that best meet the needs of their particular project.

Multi-scale finite element analysis of chloride diffusion in concrete incorporating paste/aggregate ITZs

In this paper,we propose a concurrent multi-scale finite element(FE) model coupling equations of the degree of freedoms of meso-scale model of ITZs and macroscopic model of bulk pastes.The multi-scale model is subsequently implemented and integrated into ABAQUS resulting in easy application to complex concrete structures.A few benchmark numerical examples are performed to test both the accuracy and efficiency of the developed model in analyzing chloride diffusion in concrete.These examples clearly demonstrate that high diffusivity of ITZs,primarily because of its porous microstructure,tends to accelerate chloride penetration along concentration gradient.The proposed model provides new guidelines for the durability analysis of concrete structures under adverse operating conditions.

Lagrangian-based spatial-temporal topological study on the evolution and migration of coherent structures in wall turbulence

In this work,we study the development,evolution,and migration of turbulent coherent structures in the turbulent boundary layer at Reτ=630 using time-resolved particle image velocimetry(TR-PIV).Multiple techniques,including multi-scale analysis,conditional averaging,cross-correlation,and spatial-temporal topological analysis are applied to extract the evolution principle,migration trajectory,and convection velocity vector of the targeted coherent structures from a Lagrangian perspective.The spanwise vortex structures with larger scale and intensity at a certain wall-normal height y were the main focus of the present study.In the statistical sense,spanwise vortex structures move away from the wall with the shape changing from a bulge to an ellipse,and finally to a circle.Two straight lines emerge from the mean transfer trajectory curve of the spanwise vortex,in which the horizontal one is located at the viscous sublayer(y^(+)<10),the other is a logarithmic straight line existing in the range of 50<y^(+)<120,and the inclination angle of the tangential migration path is fixed at around 12°.The streamwise convection velocity U_(c)of scaled spanwise vortex structures satisfies U_(c)/U_(∞)=0.5-0.6 below y=0.03δ(i.e.,U^(+)_(c)=11-13 undery^(+)=20).In particular,in the region of 50<y^(+)<120,the velocity growth curves of U_(c)and wall-normal convection velocity V_(c)follow the log-law distribution very well,and the slopes are consistent with that of the log-law region of the turbulent boundary layer.Our observations provide microscopic evidences of the logarithmic-linear distribution of the migration trajectory of spanwise vortex structures.