牛仔布的拔染印花工艺

选用拔染剂JN对靛蓝牛仔布进行拔染印花,拔染时,拔染浆中要加入柠檬酸以保证印浆酸性,采用低温粘合剂,选用高浓度,低含固量,增稠性强的非离子型增稠剂,并要求与粘合剂配伍性要好。

Cloning of Hoxc8 Promoter in Mongolian Sheep by Thermal Asymmetric Interlaced PCR

[Objective] The research aimed toexplore the method to obtain Hoxc8 pro- moter of Mongolian Sheep. [Method] Thermal asymmetric interlaced PCR was used to amplify the promoter sequence of Hoxc8 inMongolian Sheep. [Result] The ob- tained sequence by usingthermal asymmetric interlaced PCRwas not ideal and the sequencing results were not matching to the known sequence. Though promoter se- quence of Hoxc8 in Mongolian Sheep was not obtained by thermal asymmetric in- terlaced PCR, but the results could provide references for the relevant studies in the future. [Conclusion] The research laid the foundation for further study on the methy- lation status Hoxc8 promoter in Mongolian Sheep.

Study on Application of Natural Plant Dye Gardenia on Cotton Coloration and the Dyeing Mechanism

Based on the analysis of the structure and properties of gardenia, the gardenia was extracted in neutral bath. The mordant dyeing of cotton, including pre-mordant, one-bath and post-mordant were studied, and the dyeing properties such as dye K/S value and color fastness were investigated. According to the structure and property of mordants including alum, copper sulfate, iron sulfate and rare earth, the interaction mechanisms among gardenia, mordant and cotton fibers were analyzed and the processing factors affecting the mordant dyeing were discussed. As a result, gardenia showed favorable dyeing performance on cotton. The soaping color fastness and crocking fastness were improved by 0.5-1 grade after fixation process with the selected dye-fixing agent and optimized process conditions. The dyeing process and fixation process were optimized.

Solid oxide fuel cell:materials,technology and application

Solid oxide fuel cells (SOFCs) offer a clean, pollution-free technology for the electrochemical conversion of chemical energy of hydrocarbon fuels into electricity. Many programs are being initiated in the United States, Europe, Japan and so on. The funding for SOFC development worldwide has risen dramatically and this trend is expected to continue for at least the next decades. These development programs are also investigating wider applications of SOFCs in stationary, residential, transportation and military sectors. Finally, it is summarized the key materials and fabrication processes of SOFC in this paper.

Cytogenetic comparisons between A and G genomes in Oryza using genomic in situ hybridization

The genomic structures of Oryza sativa （A genome） and O. meyeriana （G genome） were comparatively studied using bicolor genomic in situ hybridization （GISH）. GISH was clearly able to discriminate between the chromosomes of O. sativa and O. meyeriana in the interspecific F1 hybrids without blocking DNA, and co-hybridization was hardly detected. The average mitotic chromosome length of O. meyeriana was found to be 1.69 times that of O. sativa. A comparison of 4,6-diamidino-2-phenylindole staining showed that the chromosomes of O. meyeriana were more extensively labelled, suggesting that the G genome is amplified with more repetitive sequences than the A genome. In interphase nuclei, 9-12 chromocenters were normally detected and nearly all the chromocenters constituted the G genome-specific DNA. More and larger chromocenters formed by chromatin compaction corresponding to the G genome were detected in the hybrid compared with its parents. During pachytene of the F1 hybrid, most chromosomes of A and G did not synapse each other except for 1-2 chromosomes paired at the end of their arms. At meiotic metaphase I, three types of chromosomal associations, i.e.O, sativa-O, sativa （A-A）, O. sativa-O, meyeriana （A-G） and O. meyeriana-O, meyeriana （G-G）, were observed in the F1 hybrid. The A-G chromosome pairing configurations included bivalents and trivalents. The results provided a foundation toward studying genome organization and evolution of O. meyeriana.

Characteristics of Membrane Fouling in an Anaerobic-(Anoxic/Oxic)~n-MBR Process

The characteristics of membrane fouling and cleaning, in a hybrid MBR process, was investigated. Under the condition of sub-critical flux operation, a characteristic three-stage trans-membrane pressure （TMP） profile is observed as time passes. The initially extended period of slow pressure rise, followed by a somewhat faster rise, is then sup- planted by a sudden transition to rapid pressure rise. Membrane cleaning experiments and SEM examination make it apparent that the rapid TMP rise is mainly caused by the accumulation of a surface cake layer, which is a reversible fouling that can be removed by tap water washing. Fouling caused by a gel layer, which is an irreversible fouling, can be removed efficiently by chemical cleaning. NaC10 can oxidize the gel layer, which is formed mainly of macromo-lecular organic substances. The HC1 can remove inorganic particles formed by Ca^2＋, Mg^2＋ ions etc. The sequence of chemicals used in membrane cleaning has an influence on the cleaning result. The effect of the NaC1O＋HC1 cleaning procedure is superior to that of the HCI＋NaC1O one. Particle size distribution measurements （PSD） reveal that fine particles are inclined to deposit or attach on the membrane surface, or in the membrane pores, and caused rapid fouling.

Evaluating lake eutrophication with enhanced thematic mapper data in Wuhan

By analyzing the enhanced thematic mapper (ETM) images of September 1999, and quality observation data for many consecutive years in several parts of the Donghu Lake in Wuhan, China, the authors discovered a good linear relation between grey scale (GS) abstracted from ETM b5, b7 images and eutrophication level of the lakes, and extended the study to eight other major lakes in the area of Wu- han by using lake eutrophication models. Based on the in situ monitoring data, we also evaluated the eu- trophication level of the lakes with modified trophic index method brought by M. Aizaki et al. The results of the two methods showed that the most of the lakes were eutrophicated, and even hyper-eutrophicated in some areas. Six of the 8 lakes had very similar trophic state index (TSI) values. Although two of them differed in TSI value, but within an order, while it was different largely from the one by traditional method. The difference of the results between the two methods might have been due to three causative reasons. First, remote sensing technology reflects the overall status of a certain area corresponding to the ETM images in a certain period, but the modified TSI reflects the annual average values of the monitoring spots. Second, the time the ETM images taken is later than that of in situ data. Third, ETM images are affected by clouds, water depth, and suspended matter. In short, remote sensing result agreed greatly with the in situ monitoring data, indicating that remote sensing technology is feasible and effective for moni- toring and evaluating the lake eutrophication in the Wuhan area and it also can be used to evaluate large-scope lake eutrophication.

Comparison of clonogenic assay with premature chromosome condensation assay in prediction of human cell radiosensitivity

AIM： To determine whether the number of non-rejoining G2-chromatid breaks can predict the radiosensitivity of human cell lines. METHODS： Cell lines of human ovary carcinoma cells （HO8910）, human hepatoma cells （HepG2） and liver cells （L02） were irradiated with a range of doses and assessed both of cell survival and non-rejoining G2-chromatid breaks at 24 h after irradiation. Cell survival was documented by a colony assay. Non-rejoining G2-chromatid breaks were measured by counting the number of non-rejoining G2 chromatid breaks at 24 h after irradiation, detected by the prematurely chromosome condensed （PCC） technique. RESULTS： A linear-quadratic survival curve was observed in three cell lines, and HepG2 was the most sensitive to γ-radiaUon. A dose-dependent linear increase was observed in radiation-induced non-rejoining G2- PCC breaks measured at 24 h after irradiation in all cell lines, and HepG2 was the most susceptible to induction of non-rejoining G2-PCC breaks. A close correlation was found between the clonogenic radiosensitivity and the radiation-induced non-rejoining G2-PCC breaks （r=0.923）. Furthermore, survival-aberration correlations for two or more than two doses lever were also significant. CONCLUSION： The number of non-rejoining G2 PCC breaks holds considerable promise for predicting the radiosensitMty of normal and tumor cells when two or more than two doses lever is tested.

Assessment of Groundwater Pollution Potential through GIS Technique： A Case Study for Pelly-Mianrudan Plain, Lali Urban District, Iran

Considering the low average rainfall in the country and the importance of groundwater as a water supply source for drinking and agricultural water sections, water quality condition of groundwater must be controlled and prevented from any contamination. Identifying the vulnerable areas to pollution is one way of prevention. Many models have been offered for this purpose. In this study, a numerical rating scheme, called DRASTIC has been used for evaluating potential for groundwater pollution in pelly-mianrudan plain that is located in northern Lalli city in Khuzestan province. Resulted map obtained in GIS environment shows that the study area has DRASTIC index of 71-150 that is divided to five vulnerable zones namely no significance, very low, low, low to moderate, moderate to high. Maximum groundwater vulnerability correspondent low to medium zone that approximately covers 45 percentage of the study area and other parts on the northwest and center of the study area has high vulnerability. The sensitivity analysis showed that correlation DRASTIC index with net Recharge （0.68） and Impact of vadose zone media （0.63） parameters is more than other parameters in the study pelly-mianrudan area. The statistical analysis confirms that parameter soil media and topography are the most sensitive to contamination, followed in importance by parameters aquifer medium, vadose zone, recharge, hydraulic conductivity and depth to water.

Polychlorinated dibenzo-p-dioxins and dibenzofurans in flue gas emissions from municipal solid waste incinerators in China

Polychlorinated dibenzo-p-dioxins and furans （PCDD/Fs） emissions in flue gas from two types of municipal solid waste incinerators （MSWIs） most commonly used in China were investigated in this study. The selected incinerators include two grate-type MSWIs： MSWI-A （350 t/d） and MSWI-B 050 t/d）, and two fluidized bed MSWIs： MSWI-C （400 t/d） and MSWI-D （400 t/d）, which are all equipped with semi-dry lime scrubber and bag filter except MSWI-D equipped with cyclone and wet scrubber （WS） as air pollutant control device （APCD）. Results indicated that the emission concentration and the international toxic equivalents （I-TEQs） of the PCDD/Fs from the stacks were in the range of 1.210-10.273 ng/Nm^3 and 0.019-0.201 ng I-TEQ/Nm^3, respectively. They were greatly lower than the emission regulation standard of PCDD/Fs in China （1.0 ng I-TEQ/Nm^3）. However, only the PCDD/Fs emission level from MSWI-C was below 0.1 ng I-TEQ/Nm^3. Although the homologue profiles were distinct, the contributions of the 2,3,7,8-subsituted congeners to the total I-TEQ were similar among all the investigated MSWIs. Two major 2,3,7,8-substituted congeners, 2,3,4,7,8-PeCDF and 1,2,3,7,8-PeCDD, account for 47% and 9% （average values） of the total I-TEQ values, respectively. The correlation between PCDD/Fs levels and composition of flue gas was also discussed.

Use of Probiotics in Aquaculture

Diseases of cultured animal and environmental pollution are very important problems in aquaculture. The use of probiotics in aquaculture has more advantages than the use of antibiotics and chemicals in aquaculture. This review introduces the use and mechanisms of the probiotics in aquaculture.

BURDEN OF ABNORMAL HEMATOPOIETIC CLONE IN PATIENTS WITH MYELODYSPLASTIC SYNDROMES

Objective To investigate the role of the burden of abnormal hematopoietic clone in the development of myelodysplastic syndromes (MDS). Methods The ratio of the bone marrow cells with abnormal chromosomes to the total counted bone marrow cells was regarded as the index of MDS clone burden. The disease severity related parameters including white blood cell count, hemoglobin, platelet count, lactate dehydrogenase level, bone marrow blast, myeloid differentiation index, micromegakaryocyte, transfusion, interleukin-2, tumor necrosis factor (TNF), CD4^+ and CD8^+ T cells of MDS patients were assayed, and the correlations between those parameters and MDS clone burden were also analyzed. Results The clone burden of MDS patients was 67.4%±36.2%. MDS clone burden positively correlated with bone marrow blasts (r = 0.483, P<0.05), negatively with hemoglobin level (r=-0.445, P<0.05). The number of blasts, hemoglobin, and erythrocytes in high clone burden (>50%) and low clone burden (≤50%) groups were 7.78%±5.51% and 3.45%±3.34%, 56.06±14.28 g/L and 76.40±24.44 g/L, (1.82±0.48)×10~ 12 /L and (2.32±0.66)×10~ 12 /L, respectively (all P<0.05). CD4^+ T lymphocytes of MDS patients and normal controls were (0.274±0.719)×10~ 9 /L and (0.455±0.206)×10~ 9 /L, respectively (P<0.05). CD8^+ T lymphocytes of MDS patients and normal controls were (0.240±0.150)×10~ 9 /L and (0.305±0.145)×10~ 9 /L, respectively. The serum level of interleukin-2 of MDS patients (6.29±3.58 ng/mL) was significantly higher than normal control (3.11±1.40 ng/mL, P<0.05). The serum level of TNF of MDS patients and normal control group were 2.42±1.79 ng/mL and 1.68±0.69 ng/mL, respectively. The ratio of CD4 to CD8 was higher in high clone burden MDS patients (1.90±0.52) than that in low clone burden patients (0.97±0.44, P<0.05). Conclusion The quantitive clonal karyotype abnormalities and deficient T cell immunity are important parameters for evaluating MDS severity and predicting its progression.

Impact of Artificial Perspiration on Photo-stability of Reactive Dyes on Cellulose

The photo-reactions between metabolic products of human sweat and dyestuffs on garments may produce many toxic substances which could directly contact skin and threaten human health. In order to investigate the impact of the perspiration on photo-fading of reactive dyes on cellulose, nine commercial reactive dyes belonging to three types of chromophores (azo, Cu-complex azo and anthraquinone) respectively were chosen and their perspiration-light stability on cotton fabric was studied following ATTS test standard. It is found that the impact of the artificial perspiration on dyes varies with different chromophores: anthraquinone reactive dyes always show the best photo-stability, whereas Cu-complex azo reactive dyes appear to be the most sensitive under exposure to light and perspiration. The pH value of perspiration also greatly influences the fading of dyes with different reactive groups: the fading rate of most chlorotriazinyl reactive dyes in acidic perspiration (pH=3.5) is higher than in alkaline perspiration (pH=8.0), while the reverse is true for most vinylsulphonyl dyes. Furthermore, the study of the contribution of individual component of the artificial perspiration discloses that L-Histidine monohydrochloride monohydrate, DL-Aspartic acid and lactic acid play the major roles on the photo-fading of those selected dyestuffs and inorganic salts including disodium hydrogen phosphate and sodium chloride usually decelerate photo-fading.

Sonochemical Decolorization of Methyl Orange in Aqueous Solution

The sonochemical decolorization of Methylene Orange was studied using a 24 kHz Ultrasound device with a 1.4 cm diameter horn. pH, power density, the effects of pH and power density on decolorization were discussed. The combined effect of radiate time, the initial concentration of dyes and the addition of Fe^2＋ on the decolorization was studied using response surface methodology. The results showed that the factorial central composite design was successfully employed for experimental design and predication of the results. AtpH = 2.8, T=30℃, power denstity= 300 W/L and Fe^2＋ of 2 mg/L, the decolorization percentage of 5 mg/L dye solution reached 96% after 60 mill ultreatment. The rate of decolorization of the dye was greatly improved in the presence of Fe^2＋. The sonolysis of the dye followed first-order kinetics.

Clean Coal Technologies in China： Current Status and Future Perspectives

Coal is the dominant primary energy source in China and the major source of greenhouse gases and air pollutants. To facilitate the use of coal in an environmentally satisfactory and economically viable way, clean coal technologies （CCTs） are necessary. This paper presents a review of recent research and development of four kinds of CCTs： coal power generation; coal conversion; pollution control; and carbon capture, utilization, and storage. It also outlines future perspectives on directions for technology re search and development （R＆D）. This review shows that China has made remarkable progress in the R＆D of CCTs, and that a number of CCTs have now entered into the commercialization stage.

Study on Dyeing Behavior of Modified Flax

The study of dyeability of the modified flax that uses dye-uptake to reflect its modifying effect is reported in this paper. The optimal technological condition is that the concentration of the modifying agent is 4 g/l, and NaOH is 6 g/l at liquor ratio of 1∶30 for 60 min. at 85℃.Dyeability include uptake rate and color fastness. Dye-uptake of the modified flax is twice more than that of the unmodified. And their color fastness doesnt fall and some of them raise 0.51 level.

Fluorescence Spectral Study on the Rhodamine B-I_3^- Association Nanoparticle System and Its Analytical Applications

In acid medium, rhodamine B（RhB）, rhodamine S（RhS）, rhodamine 6G（RhG） and butyl rhodamine B（b-RhB） have a fluorescence peak at 580, 549, 553 and 580nm, respectively. BrO^-3 oxidizes excess I^- into I^-3 Rhodamine dyes combine I^-3 to form ion association nanoparticles, resulting in fluorescence quenching at 580, 549, 553 and 580 rim, respectively. The fluorescence quenching intensity is proportional to the concentration of BrO^-3 in the range of 0.020 4 - 0.710 μg/mL for RhB, 0.025 - 0. 512μg/mL for RhS, 0.025 - 0.260 μg/mL for RhG, 0.025 - 1.28μg/mL for b-RhB, respectively. In the four systems, RhB system has good stability and high sensitivity. Thus, a simple, sensitive fluorescence method was proposed for the determination of BrO^-3 in commercial bread additives and flours, with satisfactory results. The results of the fluorescence spectra and scan electron microscopy show that the formation of about 60 ran （RhB - I^-3） n association nanoparticles and the interface between the nanoparticles and solution are main factors that cause the fluorescence quenching.

Color Matching for Fiber Blends Based on Stearns-Noechel Model

Prediction of the formula for matching a given color standard by blending pro-dyed fibers is of considerable importance to the textile industry. This kind of formulation suffers from a lack of computer-aided tool to assist the colorist attempting to find a good recipe to reproduce a target color. In this article a tristimulus color matching algorithm based on Stcarns-Noechel model is proposed. This algorithm was run to predict recipes for 36 viscose blends. The maximum color difference is 0.97 CIELAB units. It is demonstrated that the algorithm can be used in color matching of fiber blends.

Synthesis and Application of a Polymeric Crosslinking Agent for Improving Fixation of Vinylsulfone-type Dyes on Cotton by a Pad-dry-cure Process

A new class of novel polymeric crosslinging agent （NPCA）, which contained silane coupling group and the epoxy groups, was designed and synthesized in our laboratory. NPCA was a non-formaldehyde multifunctional crosslinking polymer. The cotton fabrics dyed with 8.0% （owf） Vinylsulpone-type dyes were treated with 3.0%- 4.0% NPCA, 0.5 mol/L potassium thiocyanate as a catalyst, then padded through two dips and two nips to reach a wet pickup of 80%- 85%, then dried at 80℃ for 2 minutes and cured in oven at 140- 150℃ for 3 minutes. Crocking fastness and fixation （%） were improved with up to 1.0 -1. 5 units, 35%- 50%, respectively. And there was little difference between the color yield of dyed fabrics before and after the treatment at certain conditions. The possible crosslinking mechanism of NPCA was also investigated. It was concluded that NPCA can improve colorfastness of cotton fabric by means of the three-dimensional network, covalent bonding and other molecular forces.

Dyeing of Polypropylene Fibers with Vat Dyes

Polypropylene fibers have been extensively used in a variety of/products, including carpets and upholstery, due to their non-absorbency, good weather resistance, good resistance to macroorgamsms and so on. Because of their hydrophobic and highly crystalline nature, those well-established conventionai dyeing processes are difficult to apply to unmodified polypropylene. Colors of polypropylene fibers are primarily obtained by mass coloration which has the disadvantages of limited number of colors available and difficulties in inventory control due to the rapidly changing color needs of the market. In this paper, the use of vat dyes to dye polypropylene fabrics is investigated. Seventeen vat dyes were screened and factors influencing uptake of dyes by polypropylene fabrics were studied.