柱塞泵主轴球窝加工研究

针对车间在产工件柱塞泵轴,分析该工件球窝部分的技术要求及加工难点,引入NX8.5软件进行刀路轨迹设计,给出一种倒扣加工的方法,使用VERICUT软件进行仿真加工,并进行模型实体与加工实体误差分析,根据分析报告对刀路轨迹进行改进。

直轴斜盘式柱塞泵常见故障的排除

本文归纳了国产典型直轴斜盘式柱塞泵及关键零部件在使用过程中的常见故障,分析了故障原因并提出处理措施。

直轴斜盘式柱塞泵常见故障的排除

该文归纳了国产典型直轴斜盘式柱塞泵及关键零部件在使用过程中的常见故障,分析了故障原因并提出处理措施。

浅析高压顶轴柱塞泵在钢球磨煤机上的应用

本文通过对点接触和面接触滑动轴瓦结构的分析,综述高压顶轴柱塞泵在钢球磨煤机上的重要作用以及在应用过程中应注意的问题。

关于斜柱塞泵问题

简介了直轴—斜轴柱塞泵结构原理,根据直轴式(斜盘式)柱塞泵到斜轴式柱塞泵的 演化原理,推论出直轴—斜轴泵可以演化成斜轴—斜轴柱塞泵,供研究参考。

工程机械液压柱塞泵使用与维修新探

本文以直轴斜盘式柱塞泵为例,介绍关于工程机械液压柱塞泵使用与维修的几种新的方法。

农业机械液压系统柱塞泵的维修

农业机械液压系统的效率主要取决于液压泵的容积效率，当容积效率下降到72％时，就需要进行常规维修，更换轴承和老化的密封件，更换或修复超出配合间隙的摩擦副，使其性能得到恢复。现以直轴斜盘式柱塞泵为例，介绍其使用及维修方法。

Distribution characteristics and impact on pump＇s efficiency of hydro-mechanical losses of axial piston pump over wide operating ranges

A novel performance model of losses of pump was presented,which allows an explicit insight into the losses of various friction pairs of pump.The aim is to clarify that to what extent the hydro-mechanical losses affect efficiency,and to further gain an insight into the variation and distribution characteristics of hydro-mechanical losses over wide operating ranges.A good agreement is found in the comparisons between simulation and experimental results.At rated speed,the hydro-mechanical losses take a proportion ranging from 87% to 89% and from 68% to 97%,respectively,of the total power losses of pump working under 5 MPa pressure conditions,and 13% of full displacement conditions.Furthermore,within the variation of speed ranging from 48% to 100% of rated speed,and pressure ranging from 14% to 100% of rated pressure,the main sources of hydro-mechanical losses change to slipper swash plate pair and valve plate cylinder pair at low displacement conditions,from the piston cylinder pair and slipper swash plate pair at full displacement conditions.Besides,the hydro-mechanical losses in ball guide retainer pair are found to be almost independent of pressure.The derived conclusions clarify the main orientations of efforts to improve the efficiency performance of pump,and the proposed model can service for the design of pump with higher efficiency performance.

Tribological performance of MoS2 coating on slipper pair in axial piston pump

This study investigates tribological performance of MoS2 coating on slipper pair in axial piston pump.Firstly,the MoS2 coating on the surface of slipper pair was prepared by atmospheric plasma spraying treatment technology.Secondly,the tribological characteristics of slipper pair under various working conditions were evaluated on ring-on-block tester in oil lubrication.The original and worn surfaces of the specimens were analyzed with scanning electron microscope and energy dispersive spectrometer,and then the wear morphologies of the MoS2 coatings were imaged by X-ray photoelectron spectroscopy.The experimental results showed that the friction coefficients of Cu-based materials with MoS2 coating decreased by about 0.05 at 800 N.Especially,when the external load was set to 800 N,the wear rate of the ZY331608 decreased by about 16.4%after the substrates were treated by the MoS2 coating,which exhibited excellent anti-friction and wear resistance.The formation of the MoS2 lubricating film could be classified into four stages,including the initial friction stage,anchoring stage of MoS2 on friction surface,covering stage of the sliding surface by MoS2 and the formation stage of MoS2 film.The dominating wear mechanisms of Cu-based materials with MoS2 coating were adhesive wear and abrasive wear accompanied with oxidative wear.

Analysis of pressure pulsation mechanism and dynamic characteristics of axial piston pump

The pressure pulsation of axial piston pump is not only an important cause of rotation speed fluctuation,vibration noise and output stability of the hydraulic system,but also the main information source for obtaining fault information.Hydraulic system is characterized by strong noise interference,which leads to low signal-to-noise ratio(SNR)of detection signals.Therefore,it is necessary to dig deep into the system operating state information carried by pressure signals.Firstly,based on flow loss mechanism of the plunger pump,the mapping relationship between flow pulsation and pressure pulsation is analyzed.After that,the pressure signal is filtered and reconstructed based on standard Gabor transform.Finally,according to the time-domain waveform morphology of pressure signal,four characteristic indicators are proposed to analyze the characteristics of pressure fluctuations under different working conditions.The experimental results show that the standard Gabor transform can accurately extract high-order harmonics and phase frequencies of the signal.The reconstructed time-domain waveform of pressure pulsation of the axial piston pump contains a wealth of operating status information,and the characteristics of pulsation changes under various working conditions can provide a new theoretical basis and a method support for fault diagnosis and health assessment of hydraulic pumps,motors and key components.

Lubrication characteristics of external return spherical hinge pair of axial piston pump or motor under combined action of inclination and offset distance

External return mechanism is a mechanical structure applied to axial piston pumps.To study its lubrication characteristics,the Reynolds equation applied to an external return spherical hinge pair was deduced based on the vector equation of relative-motion velocity of the external return spherical hinge pair under the influence of external swash plate inclination and offset distance.The results show that the total friction,axial leakage flow,and maximum value of the maximum oil-film pressure increase with increasing pump-shaft speed and decrease with increasing offset distance in one working cycle when the external-swash-plate inclination is constant.However,the varying offset distance has little effect on the axial leakage flow.The maximum value of the maximum oil-film pressure decreases with increasing external-swash-plate inclination and the total leakage flow increases with increasing external-swash-plate inclination in one working cycle when the offset distance is constant.It can be seen that the abovementioned parameters are important factors that affect the lubrication characteristics of external return spherical hinge pairs.Therefore,the complex effects of different coupling parameters should be comprehensively considered in the design of the external return mechanism.

Parametric analysis of thermal effect on hydrostatic slipper bearing capacity of axial piston pump

Hydrostatic slipper was often used in friction bearing design, allowing improvement of the latter's dynamic behavior. The influence of thermal effect on hydrostatic slipper bearing capacity of axial piston pump was investigated. A set of lumped parameter mathematical models were developed based on energy conservation law of slipper/ swash plate pair. The results show that thermal equilibrium clearance due to solid thermal deformation periodically changes with shaft rotational angle. The slipper bearing capacity increases dramatically with decreasing thermal equilibrium clearance. In order to improve the slipper bearing capacity, length-to-diameter ratio of fixed damper varies from 3.5 to 8.75 and radius ratio of slipper varies from 1.5 to 2.0. In addition, the higher slipper thermal conductivity is useful to improve slipper bearing capability, but the thermal equilibrium clearance is not compromised.

A new design method for the transition region of the valve plate for an axial piston pump

The optimization of the valve plate transition region is an important way of reducing the noise emission for an axial piston pump. However, the optimized methods through simulation or experiment are actually trial and error, and they cannot indicate the precise structural parameters of the valve plate transition region. In this study, a new design method for the transition region of valve plate based on the matching of flow area and reduction of transient reverse flow was proposed, and with which a valve plate was designed. Then, the impact of the flow ripple in the discharge line of an axial piston pump and the pressure overshoot and undershoot in the piston chamber on hydraulic and structural noise for axial piston pump is discussed. The noise reduction effect of the axial piston pump with this valve plate was analyzed by adopting a flow characteristic simulation model. Finally, the results showed that the application of this design method could contribute much to the reduction of the flow ripple and elimination of the pressure overshoot and undershoot. As a consequence, the method can be used in the design of a low-noise open circuit axial piston pump.

Investigation on structural optimization of anti-overturning slipper of axial piston pump

Improving the carrying ability of oil film between slipper and swash plate and reducing the partial abrasion of slipper are important to improve the service life and reliability of axial piston pump.In this paper,a numerical simulation model was developed for slipper/swash-plate friction pair based on the elastohydrodynamic theory.The dynamic micro-motion and pressure distribution of slipper were analyzed and it was pointed out that the tilt of slipper was the main reason for its partial abrasion.The simulations about the slippers with different slopes on the outer edge of the sealing belt showed that the partial abrasion could reduce the carrying ability and increase the leakage of the slipper/swash-plate pair.The proper slope on the inner edge helped to improve the carrying ability and reduce the leakage of slipper.The experimental tests were in accord with the simulation results to a great extent,showing that the simulation model had a high accuracy and could be applied to the design and optimization of slipper,and that the slipper with optimal inner slope provided an encouraging method to improve the efficiency and reliability of axial piston pump.