Today’s vehicles use electronic control units(ECU) to control engine/transmission, body and other amenities. All the vehicle performance depends on a lot of physical values and influence factors. This leads to a larg...Today’s vehicles use electronic control units(ECU) to control engine/transmission, body and other amenities. All the vehicle performance depends on a lot of physical values and influence factors. This leads to a large number of control and regulation parameters in the ECU software. The ultimate objective of calibration work is the optimum determination of these parameters. Qualitatively excellent results can only be achieved in a shorter time by using a highly efficient calibration system. This paper provided an overview of a new calibration tool based on KWP2000 and gave an example calibration with this tool.展开更多
Abstract： Excess of organic matter and nutrients in water promotes eutrophication process observed in the Ardila River. It was classified as much polluted being critical for Alqueva-Pedrogāo System. The aim of this ...Abstract： Excess of organic matter and nutrients in water promotes eutrophication process observed in the Ardila River. It was classified as much polluted being critical for Alqueva-Pedrogāo System. The aim of this study was to estimate the transported nutrients loads in a transboundary watershed using the SWAT （soil and water assessment tool） model and to determine the contribution of nutrients load in the entire watershed. Ardila watershed is about 3,711 km^2 extended from Spain （78%） to the eastern part of Portugal （22%）. It was discretized into 32 sub-basins using automated delineation routine, and 174 hydrologic response units. Monthly average meteorological data （from 1947 to 1998） were used to generate daily values through the weather generator Model incorporated in SWAT. Real daily precipitation （from 1931 to 2003） was introduced. The model was calibrated and verified for flow （from 1950 to 2000） and nutrients （from 1981 to 1999）. Model performance was evaluated using statistical parameters, such as NSE （Nash-Sutcliffe efficiency） and root mean square error （R2）. Calibration and verification flow results showed a satisfactory agreement between simulated and measured monthly date from 1962 to 1972 （NSE = 0.8; R^2 = 0.9）. The results showed that the most important diffuse pollution comes from the two the main tributary （Spain）. The estimated nitrogen and phosphorous loads contribution per year was respectively 72% and 59% in Spain and 28% and 41% in Portugal. The SWAT model was revealed to be a useful tool for an integrated water management approach that might be improved taking into count the WFD （water framework directive）.展开更多
This paper mainly design B/S system structure and small information management system that often appear some problems of college student information management, combines the actual situation of students and student in...This paper mainly design B/S system structure and small information management system that often appear some problems of college student information management, combines the actual situation of students and student instructor management work. In the process of the development of the whole system, the main use of Microsoft.NET technology as a whole system of compiler environment, SQL Server 2000 is used in the design of backstage supporter＇ s database, were developed and designed by Visual Studi02005 tool, in exchange for page dynamically selected by the ASP.NET database and system interface between Webpage generation. This system has high reliability, high security, low input, so that the efficiency of information management students to improve.展开更多
A novel approach is proposed for correcting command points and compressing discrete axis commands into a C2 continuous curve.The relationship between values of rotation angles and tool posture errors is firstly analyz...A novel approach is proposed for correcting command points and compressing discrete axis commands into a C2 continuous curve.The relationship between values of rotation angles and tool posture errors is firstly analyzed.A segmentation method based on values of rotation angles and lengths of adjacent points is then used to subdivide these command points into accuracy regions and smoothness regions.Since tool center points generated by CAD/CAM system are usually lying in the space that is apart from the desired curve within a tolerance distance,and the corresponding tool orientation vector may change a lot while the trajectory length of the tool center point is quite small,directly machining with such points will lead to problems of coarse working shape and long machining time.A correction method for command points is implemented so that good processing effectiveness can be achieved.Also,the quintic spline is used for compressing discrete command points into a C2 continuous smooth curve.The machining experiment is finally conducted to demonstrate the effectiveness of the proposed algorithm.展开更多
文摘Today’s vehicles use electronic control units(ECU) to control engine/transmission, body and other amenities. All the vehicle performance depends on a lot of physical values and influence factors. This leads to a large number of control and regulation parameters in the ECU software. The ultimate objective of calibration work is the optimum determination of these parameters. Qualitatively excellent results can only be achieved in a shorter time by using a highly efficient calibration system. This paper provided an overview of a new calibration tool based on KWP2000 and gave an example calibration with this tool.
文摘Abstract： Excess of organic matter and nutrients in water promotes eutrophication process observed in the Ardila River. It was classified as much polluted being critical for Alqueva-Pedrogāo System. The aim of this study was to estimate the transported nutrients loads in a transboundary watershed using the SWAT （soil and water assessment tool） model and to determine the contribution of nutrients load in the entire watershed. Ardila watershed is about 3,711 km^2 extended from Spain （78%） to the eastern part of Portugal （22%）. It was discretized into 32 sub-basins using automated delineation routine, and 174 hydrologic response units. Monthly average meteorological data （from 1947 to 1998） were used to generate daily values through the weather generator Model incorporated in SWAT. Real daily precipitation （from 1931 to 2003） was introduced. The model was calibrated and verified for flow （from 1950 to 2000） and nutrients （from 1981 to 1999）. Model performance was evaluated using statistical parameters, such as NSE （Nash-Sutcliffe efficiency） and root mean square error （R2）. Calibration and verification flow results showed a satisfactory agreement between simulated and measured monthly date from 1962 to 1972 （NSE = 0.8; R^2 = 0.9）. The results showed that the most important diffuse pollution comes from the two the main tributary （Spain）. The estimated nitrogen and phosphorous loads contribution per year was respectively 72% and 59% in Spain and 28% and 41% in Portugal. The SWAT model was revealed to be a useful tool for an integrated water management approach that might be improved taking into count the WFD （water framework directive）.
文摘This paper mainly design B/S system structure and small information management system that often appear some problems of college student information management, combines the actual situation of students and student instructor management work. In the process of the development of the whole system, the main use of Microsoft.NET technology as a whole system of compiler environment, SQL Server 2000 is used in the design of backstage supporter＇ s database, were developed and designed by Visual Studi02005 tool, in exchange for page dynamically selected by the ASP.NET database and system interface between Webpage generation. This system has high reliability, high security, low input, so that the efficiency of information management students to improve.
基金supported by the National Key Basic Research and Development Projects under Grant No.2011CB302400
文摘A novel approach is proposed for correcting command points and compressing discrete axis commands into a C2 continuous curve.The relationship between values of rotation angles and tool posture errors is firstly analyzed.A segmentation method based on values of rotation angles and lengths of adjacent points is then used to subdivide these command points into accuracy regions and smoothness regions.Since tool center points generated by CAD/CAM system are usually lying in the space that is apart from the desired curve within a tolerance distance,and the corresponding tool orientation vector may change a lot while the trajectory length of the tool center point is quite small,directly machining with such points will lead to problems of coarse working shape and long machining time.A correction method for command points is implemented so that good processing effectiveness can be achieved.Also,the quintic spline is used for compressing discrete command points into a C2 continuous smooth curve.The machining experiment is finally conducted to demonstrate the effectiveness of the proposed algorithm.
