Estimating the deformation of soil around the pile contributes to reliable design of structures under pullout force. This work presents the results of a series of small-scale physical modelling tests designed to inves...Estimating the deformation of soil around the pile contributes to reliable design of structures under pullout force. This work presents the results of a series of small-scale physical modelling tests designed to investigate the uplift resistance of piles with diameter of 5 cm and slenderness ratios of 1, 2, 3 and 4 in loose sand. Close photogrammetric technique and particle image velocimetry(PIV) were employed to observe the failure patterns due to uplift force on piles. The results show that the shear zones curve slightly outward near the ground surface. After peak resistance, the shear strain concentrates into a pair of narrow shear bands,then a flow around mechanism is formed accompanied by a reduction in the uplift resistance. The results from the laboratory tests were verified by analytical method proposed by Chattopadhyay and PLAXIS 2D and 3D finite element method software. It is found that the depth and width of the failure surface increase with the increment of the slenderness ratio. A good agreement is observed among the measured bearing capacity and obtained failure surface of the models and the results of numerical modelling. Finally, the maximum deformation of loose and dense sand respectively with densities of 25% and 75% were compared in the stage of fully removing pile. The results shows that the deformation of the soil is related to its density, therefore it depends on its dilatancy.展开更多
A developed stereo particle image velocimetry(stereo-PIV) system was proposed to measure three-dimensional(3D) soil deformation around a laterally loaded pile in sand.The stereo-PIV technique extended 2D measurement t...A developed stereo particle image velocimetry(stereo-PIV) system was proposed to measure three-dimensional(3D) soil deformation around a laterally loaded pile in sand.The stereo-PIV technique extended 2D measurement to 3D based on a binocular vision model,where two cameras with a well geometrical setting were utilized to image the same object simultaneously.This system utilized two open software packages and some simple programs in MATLAB,which can easily be adjusted to meet user needs at a low cost.The failure planes form an angle with the horizontal line,which are measured at 27°-29°,approximately three-fourths of the frictional angle of soil.The edge of the strain wedge formed in front of the pile is an arc,which is slightly different from the straight line reported in the literature.The active and passive influence zones are about twice and six times of the diameter of the pile,respectively.The test demonstrates the good performance and feasibility of this stereo-PIV system for more advanced geotechnical testing.展开更多
文摘Estimating the deformation of soil around the pile contributes to reliable design of structures under pullout force. This work presents the results of a series of small-scale physical modelling tests designed to investigate the uplift resistance of piles with diameter of 5 cm and slenderness ratios of 1, 2, 3 and 4 in loose sand. Close photogrammetric technique and particle image velocimetry(PIV) were employed to observe the failure patterns due to uplift force on piles. The results show that the shear zones curve slightly outward near the ground surface. After peak resistance, the shear strain concentrates into a pair of narrow shear bands,then a flow around mechanism is formed accompanied by a reduction in the uplift resistance. The results from the laboratory tests were verified by analytical method proposed by Chattopadhyay and PLAXIS 2D and 3D finite element method software. It is found that the depth and width of the failure surface increase with the increment of the slenderness ratio. A good agreement is observed among the measured bearing capacity and obtained failure surface of the models and the results of numerical modelling. Finally, the maximum deformation of loose and dense sand respectively with densities of 25% and 75% were compared in the stage of fully removing pile. The results shows that the deformation of the soil is related to its density, therefore it depends on its dilatancy.
基金Project(104244) supported by the Natural Sciences and Engineering Research Council of Canada
文摘A developed stereo particle image velocimetry(stereo-PIV) system was proposed to measure three-dimensional(3D) soil deformation around a laterally loaded pile in sand.The stereo-PIV technique extended 2D measurement to 3D based on a binocular vision model,where two cameras with a well geometrical setting were utilized to image the same object simultaneously.This system utilized two open software packages and some simple programs in MATLAB,which can easily be adjusted to meet user needs at a low cost.The failure planes form an angle with the horizontal line,which are measured at 27°-29°,approximately three-fourths of the frictional angle of soil.The edge of the strain wedge formed in front of the pile is an arc,which is slightly different from the straight line reported in the literature.The active and passive influence zones are about twice and six times of the diameter of the pile,respectively.The test demonstrates the good performance and feasibility of this stereo-PIV system for more advanced geotechnical testing.
