5X密度磁光盘模压特性检测的定时逻辑控制

讨论 ５ Ｘ 密度磁光盘模压特性检测系统中的关键技术之一——定时与逻辑控制．该定时与逻辑控制电路通过模压预格式信号中的自同步位时钟与 Ｓ Ｍ 标志指示信号对模压预格式信号中的各个区段 （ Ｓ Ｍ ， Ｖ Ｆ Ｏ， Ａ Ｍ， Ｉ Ｄ， Ｐ Ａ） 在时域上定位，实现对具有高速非重复性的模压预格式信息的实时采集，从而满足检测系统对包括磁光盘扇区标头信号、跨道信号和推挽信号的模压预格式信息的测试要求．

Elastic modulus determination at different levels of periodontal ligament in nanoindentation

In order to investigate the material properties ofperiodontal ligament （ PDL） in different locations, the nanoindentation method is used to survey the elastic modulus of the PDL at different levels. Cadaveric specimens of human mandibular canine were obtained from 4 adult donors, 16 transverse specimens were made from the sections of cervical margin, midroot and apex using the slow cutting machine. The prepared specimens were tested in different sections （along the longitudinal direction） and different areas （in the circumferential direction）. According to the Oliver-Phair theory, the mean values of elastic modulus were calculated foreach area and the differences among them were compared. In the midroot section, the average elastic modulus is ranging from 0. 11 to 0. 23 MPa, the changing range of the cervical margin and apex are from 0. 21 to 0. 53 MPa and 0. 44 to0.62 MPa, respectively. Experimental results indicate that the average elastic modulus in the midroot is lower than that in the cervical margin and apex, and relatively small changes occur among them. However, there is a large change to the elastic modulus value in the cicumferential direction for the PDL.

Quantum Entanglement and Nonlocality Properties of Two-Mode Squeezed Thermal States in a Common-Reservoir Model

We study a system consisting of two identical non-interacting single-mode cavity fields coupled to a common vacuum environment and provide general, explicit, and exact solutions to its master equation by means of the characteristic function method. We analyze the entanglement dynamics of two-mode squeezed thermal state in this model and show that its entanglement dynamics is strongly determined by the two-mode squeezing parameter and the purity. In particular, we find that two-mode squeezed thermal state with the squeezing parameter r ≤ -（1/2） In √u is extremely fragile and almost does not survive in a common vacuum environment. We investigate the time evolution of nonlocality for two-mode squeezed thermal state in such an environment. It is found that the evolved state loses its nonlocality in the beginning of the evolution, but after a time, the revival of nonlocality can occur.

Failure mode and strength anisotropic characteristic of stratified rock mass under uniaxial compressive situation

A stratified rock mass model was founded by FLAC^3D. The failure mode and anisotropic characteristic of strength for stratified rock mass were analyzed. The analysis results show that the numerical simulation can visually reflect the failure modes of rock samples under different inclination angles β of structural plane. The stiffness of rock sample before peak strength changes in the compressive procedure. With the increase of β, the compressive strength σc of rock sample decreases firstly and then increases; when β is in the range of 20°-30° and 80°-90°, σc has the largest sensitivity to r; while β falls in the range of 30°-70°, σc varies little. When φj〈β〈90° （ φj is friction angle of structure plane）, the results obtained from numerical simulation and theoretical analysis are in almost the same values; while β〈 φj or β=90°, they are in great different values. The results obtained from theoretical analysis are obvious larger than those from numerical simulation; and the results from numerical simulation can reflect the difference of compressive strength of rock samples for the two situations of β≥φj and β=90°, which is in more accordance with the real situation.

Enhanced heat transfer in a heat exchanger square-duct with discrete V-finned tape inserts

The article presents an experimental and numerical study on thermal performance enhancement in a constant heatfluxed square-duct inserted diagonally with 45° discrete V-finned tapes(DFT).The experiments were carried out by varying the airflow rate through the tested square duct with DFT inserts for Reynolds number from 4000 to 25000.The effect of the DFT with V-tip pointing upstream at various relative fin heights and pitches on heat transfer and pressure drop characteristics was experimentally investigated.Both the heat transfer and pressure drop were presented in terms of Nusselt number and friction factor respectively.Several V-finned tape characteristics were introduced such as fin- to duct-height ratio or blockage ratio(R_B=e/H = 0.075,0.1,0.15 and 0.2),fin pitch to duct height ratio(R_P= P/H=0.5,1.0,1.5 and 2.0) and fin attack angle,α = 45°.The experimental results reveal that the heat transfer and friction factor values with DFT inserts increase with the increment of R_B but the decrease of R_P.The inserted square-duct at R_B = 0.2 and R_P = 0.5 provides the highest heat transfer and friction factor while the one with R_B= 0.1 and R_P= 1.5 yields the highest thermal performance.Also,a numerical simulation was conducted to investigate the flow structure and heat transfer mechanism inside the tested duct with DFT inserts.

Mechanical and damage evolution properties of sandstone under triaxial compression

To study the mechanical and damage evolution properties of sandstone under triaxial compression, we analyzed the stress strain curve characteristics, deformation and strength properties, and failure process and characteristics of sandstone samples under different stress states. The experimental results reveal that peak strength, residual strength, elasticity modulus and deformation modulus increase linearly with confining pressure, and failure models transform from fragile failure under low confining pressure to ductility failure under high confining pressure. Macroscopic failure forms of samples under uniaxial compression were split failure parallel to the axis of samples, while macroscopic failure forms under uniaxial compression were shear failure, the shear failure angle of which decreased linearly with confin- ing pressure. There were significant volume dilatation properties in the loading process of sandstone under different confining pressures, and we analyzed the damage evolution properties of samples based on acoustic emission damage and volumetric dilatation damage, and established damage constitutive model, realizing the real-time Quantitative evaluation of samnles damage state in loading process.

Effect of loading rates on the characteristics of thermal damage for mudstone under different temperatures

The uniaxial compression tests for mudstone specimens are carried out with four different loading rates from room temperature to 400℃ by using the Rock Mechanics Servo-controlled Testing System MTS810 and high temperature furnace MTS652.02.The mechanical properties of mudstone with various loading rates are studied under different temperature conditions.The results show that when temperature increases from room temperature to 400℃ and loading rate is less than 0.03 mm/s,the peak strength of mudstone specimen decreases as loading rate increases,while the various peak strengths show significant differences when loading rate exceeds 0.03 mm/s.At room temperature,the elastic modulus decreases at the first time and then increases with loading rate rising.When the temperature is between200 and 400℃,the elastic modulus presents a decreasing trend with increasing loading rate.With increasing the loading rate,the number of fragments in mudstone becomes larger and even the powder is observed in mudstone with higher loading rate.Under high loading rate,the failure mode of mudstone specimens under different temperatures is mainly conical damage.

Distribution characteristics and impact on pump＇s efficiency of hydro-mechanical losses of axial piston pump over wide operating ranges

A novel performance model of losses of pump was presented,which allows an explicit insight into the losses of various friction pairs of pump.The aim is to clarify that to what extent the hydro-mechanical losses affect efficiency,and to further gain an insight into the variation and distribution characteristics of hydro-mechanical losses over wide operating ranges.A good agreement is found in the comparisons between simulation and experimental results.At rated speed,the hydro-mechanical losses take a proportion ranging from 87% to 89% and from 68% to 97%,respectively,of the total power losses of pump working under 5 MPa pressure conditions,and 13% of full displacement conditions.Furthermore,within the variation of speed ranging from 48% to 100% of rated speed,and pressure ranging from 14% to 100% of rated pressure,the main sources of hydro-mechanical losses change to slipper swash plate pair and valve plate cylinder pair at low displacement conditions,from the piston cylinder pair and slipper swash plate pair at full displacement conditions.Besides,the hydro-mechanical losses in ball guide retainer pair are found to be almost independent of pressure.The derived conclusions clarify the main orientations of efforts to improve the efficiency performance of pump,and the proposed model can service for the design of pump with higher efficiency performance.

On the method of the automatic modeling in hydraulic pipe networks

In this paper the dynamic characteristics in pipes are analyzed with frequency method, and puts forward a simple and practical describing method. By establishing the model library beforehand, the modeling of the pipe net is completed automatically, and we can accurately calculate the impedance characteristics of the pipe network, achieve the reasonable configuration of the pipe network, so that to decrease the pressure pulsation.

Pressure performance improvement by dual-mode control in digital pump/motor

Due to the advantages of low cost,fast response and pollution resistance,digital hydraulic pump/motor can replace conventional variable hydraulic pump/motor in many application fields.However,digital hydraulic components produce large hydraulic impact at variable moments,which will shorten the service life of mechanical components.Through the simulation analysis of the variable process of digital pump/motor,it is found that the discontinuous flow caused by displacement step changes is the fundamental cause of hydraulic impact.The data analysis results of experimental tests are in good agreement with the simulation analysis results.In view of hydraulic secondary components,a variable control method based on dual-mode operating characteristics is proposed.The TOPSIS algorithm is used to give comprehensive evaluation of the displacement control results after this method.The results show that the control quality of digital pump/motor after adopting the control method has been effectively improved,with an average improvement of about 40%.

Pressure Drop Fluctuations in Periodically Fluctuating Pipe Flow

Experiments were conducted to study characteristics of flow when flow is fluctuating.The experimental results showed a phase difference between the flow rate and the pressure drop fluctuations.This phase difference between the fluctuating flow rate and pressure drop was analyzed for laminar flow.Analysis showed that the phase difference changes with the period of the flow fluctuation, the pipe radius, the density and the dynamic viscosity of the liquid.Fluctuating pipe flow was then numerically simulated.Results of the numerical simulation were compared with theoretical values and experimental results.It was shown that, when the flow rate fluctuates with time as a sine wave, the pressure drop fluctuates with the same periodicity, and there is a phase difference between them.

Plastic characterization of metals by combining nanoindentation test and finite element simulation

Materials with the same elastic modulus E and representative stress and strain （σr,εr） present similar indentation-loading curves, whatever the value of strain hardening exponent n. Based on this definition, a good approach was proposed to extract the plastic properties or constitutive equations of metals from nanoindentation test combining finite element simulation. Firstly, without consideration of strain hardening, the representative stress was determined by varying assumed representative stress over a wide range until a good agreement was reached between the computed and experimental loading curves. Similarly, the corresponding representative strain was determined with different hypothetical values of strain hardening exponent in the range of 0-0.6. Through modulating assumed strain hardening exponent values to make the computed unloading curve coincide with that of the experiment, the real strain hardening exponent was acquired. Once the strain hardening exponent was determined, the initial yield stress ay of metals could be obtained by the power law constitution. The validity of the proposed methodology was verified by three real metals： AISI 304 steel, Fe andA1 alloy.

ELASTOPLASTIC ANALYSIS OF THICK-WALLCYLINDER CONSIDERING THE MATERIAL'S DILATANCY CHARACTER

Impermeable bentonite or its mixtures have been proposed as candidate materials to be used in the geotechnical disposal of radioactive nuclear waste. These materials are filled in the space between a canister containing radioactive nuclear waste and an underground chamber to absorb the radionuclide emitting from the canister and simultaneously retard its migration accompanying the perrneation of underground water to prevent the surrounding environment from po1lution. On the basis of the established elastoplastic strain-hardening mechanical model considering the material’s dilatancy character,the authors carry out the stress-strain analysis of a thick-wa1l cylinder in a plane strain state subJected to a pressure difference between internal and external pressures. The analysis may be expected to be a theoretical basis for developing a coupled shear and permeability test apparatus for conducting a permeability test along a sheared plane in a specimen. The apparatus will be used to study the effects of shear strain on the variation of geotechnical materials’ permeability coefficient in order to evaluate the influence of shear strain caused by nonuniform deformation and/or earthquake on the long-term safety of the disposal system of radioactive nuclear waste. The theoretlcal analysls methods in this paper can be directly spread to the analysis of the deformation and stability of tunnels or roadways driven in soft soils or high moisture-bearing soft rocks.

Measurement and Modeling for the Solubility of Hydrogen Sulfide in Primene JM-T

The primary aliphatic amine Primene JM-T was investigated as a potential absorbent for H2S removal. The solubility of HzS in JM-T was measured at 298, 313,333,353, and 368 K with H2S partial pressures from 20 to 760 kPa and HzS loading from 0.02 to 0.8 mol H2S per mol JM-T. Relevant physical properties, such as density, viscoslty and dielectric constant, ot the matenal were measured. ＇The thermodynamlc model with two-suttlX Margules equation was used to correlate the experimental vapor-liquid equilibrium data. Furthermore, the absorption mechanism in non-aqueous system is suggested and the difference between non-aqueous and aqueous absorption system is pointed out.

Functional nanogenerators as vibration sensors enhanced by piezotronic effects

ZnO nanomaterials have been shown to have novel applications in optoelectronics, energy harvesting and piezotronics, due to their coupled semiconducting and piezoelectric properties. Here a functional nanogenerator （FNG） based on ZnO nanowire arrays has been fabricated, which can be employed to detect vibration in both self-powered （SP） and external-powered （EP） modes. In SP mode, the vibration responses of the FNG can be measured through converting mechanical energy directly into an electrical signal. The FNG shows consistent alternating current responses （relative error 〈 0.37%） at regular frequencies from 1 to 15 Hz. In EP mode, the current responses of FNG are significantly enhanced via the piezotronic effect. Under a forward bias of 3 V, the sensor presented a sensitivity of 3700% and an accurate measurement （relative error 〈 0.91%） of vibration frequencies in the range 0.05-15 Hz. The results show that this type of functional nanogenerator sensor can detect vibration in both SP and EP modes according to the demands of the applications.

Analysis of two models for metal hot-electron power generation

Hot electron emission means that electrons move over potential barriers to come out of the metal when the metal is being heated.Obviously,voltage will generate between electrons and the metal.Based on this,the model of metal hot-electron power generation is built.Free electron model of Sommerfeld is used to describe the movement of electrons in metal.According to the different width of potential barriers,two models are built.One assumes that electrons move from one metal to another mainly by moving over the potential barrier as the barrier is wide enough.The other assumes that the potential barrier is so narrow that electrons mainly move through the potential barrier by tunnel effect.The first model is analyzed and proved strictly,including the building of model,the calculation of open-circuit voltage and the drawing of volt-ampere characteristic curve.The second model is analysed simply.This paper shows that power generation by metal hot-electron is possible based on the theory and can provide reference for researching in power generation of metal hot-electron.

Numerical Investigation of Rotating Stall in Centrifugal Compressor with Vaned and Vaneless Diffuser

This study presents a numerical simulation of the stall and surge in a centrifugal compressor and presents a description of the stall development in two different cases.The first case is for a compressor with vaneless diffuser and the second is for a compressor with vaned diffuser of the vane island shape.The main aim of this study is to compare the flow characteristics and behavior for the two compressors near the surge operating condition and provide further understanding of the diffuser role when back flow occurs at surge.Results showed that for a location near the diffuser entrance,the amplitude of the static pressure fluctuations for the vaneless diffuser case is higher than that for the vaned diffuser case near surge condition.These pressure fluctuations in the case of the vaneless diffuser appear with a gradual decrease of the mean pressure value as a part of the surge cycle.While for the case of the vaned diffuser,the pressure drop during surge occurs faster than the case of the vaneless diffuser.Also,results indicated that during surge in the case of vaneless diffuser,there is a region with low velocity and back flow that appears as a layer connecting all impeller passages near shroud surface and this layer develops in size with time.On the other hand,for the case of vaned diffuser during surge,the low velocity regions appear in random locations in some passages and these regions expand with time towards the shroud surface.Results showed that during stall,the impeller passages are exposed to identical impact from stall cells in the case of vaneless diffuser while the stall effect varies from passage to another in the case of the vaned diffuser.

Numerical Simulation of Flow Characteristics in Micro Shock Tubes

Recently micro shock tubes have been widely used in many engineering and industrial fields, but the characteristics of unsteady flow are not well known to date in micro shock tubes. Compared to conventional shock tubes with macro scales, flows related to shock waves in micro shock tubes are highly complicated. Stronger viscous and dissipative interactions make shock wave dynamic behaviors significantly different from theoretical predictions. In the present study, a CFD work was applied to the unsteady compressible Navier-Stokes equations which were solved using a fully implicit finite volume scheme. The diaphragm pressure ratio and shock tube diameter were varied to investigate their effects on micro shock tube flows. Different wall boundary conditions were also performed to observe shock wave and contact surface propagation with no slip and slip walls. Detailed flow characteristics at the foot of shock wave and contact surface propagation were known from the present numerical simulations.