一体化压铸模温控制系统设计与应用

一体化压铸件具有模具投影面积大和壁厚较薄等工艺特点,其生产对于模温有极高的要求,存在控温设备布局干涉和预留安装维护空间不足等问题。基于此,设计了一体化压铸模温控制系统,实现多种控温设备的硬件集成和软件集成控制,减少控温设备的布局面积,提升工作效率,并提高压铸模温控制的工艺管控能力。

Heat Transfer in Nucleate Pool Boiling of Binary and Ternary Refrigerant Mixtures

Heat transfer coefficients in nucleate pool boiling were measured on a horizontal copper surface for refrigerants, HFC-134a, HFC-32, and HFC-125, their binary and ternary mixtures under saturated conditions at 0.9MPa. Compared to pure components, both binary and ternary mixtures showed lower heat transfer coefficients.This deterioration was more pronounced as heat flux was increased. Experimental data were compared with some empirical and semi-empirical correlations available in literature. For binary mixture, the accuracy of the correlations varied considerably with mixtures and the heat flux. Experimental data for HFC-32/134a/125 were also compared with available correlated equation obtained by Thome. For ternary mixture, the boiling range of binary mixture composed by the pure fluids with the lowest and the medium boiling points, and their concentration difference had important effects on boiling heat transfer coefficients.

3D Conceptual Modeling and Direct Utilization Calculations of the Albanian Low and Middle Enthalpy Geothermal Resources

The use of the Albanian geothermal springs and waters, for their curative effects （Natural SPA） dates back centuries, since the time of the Roman Empire, while their first modern use started only in 1937. Unfortunately they had not been used for its energetic values yet. The temperature of the water is above 60 ~C and the flow above 16 L/s, thus direct utilization is possible, in particular for space heating. Three-dimensional temperature field calculations and engineering calculations on a heating system with heat exchangers are presented here. The results show that the water temperature is expected to be stable and considerably higher temperature is expected through deep well drilling. The University＇s Campus of Tirana is composed of 29 buildings, which are partially heated through a coal heater. The installed capacity is 2,558 kW while the coal consumption is about 920 kg/h. The University＇s Campus of Tirana is one of the most important areas and with the highest density of population in Tirana, so it is the best area to show the heat exchanger efficiency. The economic analyses prove that the borehole heat exchangers are more convenient than the coal heating systems.

Evaluation of pitting corrosion of thixoformed A356 alloy using a simulation model

Pitting behavior of thixoformed A356 alloy, with different reheating temperatures, was evaluated. Linear sweep voltammetric tests were used to study the pitting behavior of thixoformed, rheocast and gravity-cast A356 alloy in a 3.5% NaCl solution. A simulation method was also used in order to identify local galvanic corrosion current density between local galvanic couples. The results obtained show that the resistance to pitting corrosion of the thixoformed samples formed at 600 ℃ is higher than that of the samples formed at 610 ℃ as well as rheocast and gravity-cast samples. These results could be explained by morphological aspects of silicon phase as well as the area effect as related to galvanic corrosion between silicon particles and eutectic aluminum phase.

Simulation of Spin-3/2 Blume-Capel Model on a Cellular Automaton with Heating and Cooling Algorithm

The spin-3/2 B1ume-Capel model is studied using the heating and cooling algorithms improved from the Creutz cellular automaton （CCA）. The calculations are done on various sizes of the simple cubic lattice in the 0 ≤ D/J ≤ 5 parameter region. The phase diagram of the model and temperature variation of the thermodynamic quantities are obtained. We confirm the existence of a critical end point within the heating calculations. However, in contrast to the heating calculations, we do not obtain the first-order line at low temperature with cooling algorithm calculations. The results are compared with those of other theories.

Dark matter heating in strange stars

We study the effect of dark matter heating on the temperature of typical strange star(SS hereafter)(M=1.4 M⊙,R=10 km)in normal phase(NSS hereafter)and in a possible existing colour-flavour locked(CFL)phase(CSS hereafter).For NSS,the influence of dark matter heating is ignored until roughly 107yr.After 107yr,the dark matter heating is dominant that significantly delays the star cooling,which maintains a temperature much higher than that predicted by standard cooling model for old stars.Especially for CSS,the emissivity of dark matter will play a leading role after roughly 104yr,which causes the temperature to rise.This leads to the plateau of surface temperature appearing in～106.5yr which is earlier than that of NSS(～107yr).

Analysis and Numerical Simulation Research of the Heating Process in the Oven

How to use the oven to bake delicious food is the most concerned problem of the designers and users of the oven.For this intent,this paper analyzed the heat distribution in the oven based on the basic operation principles and proceeded the data simulation of the temperature distribution on the rack section.Constructing the differential equation model of the temperature distribution changes in the pan when the oven works based on the heat radiation and heat transmission,based on the idea of utilizing cellular automation to simulate heat transfer process,used ANSYS software to proceed the numerical simulation analysis to the rectangular,round-cornered rectangular,elliptical and circular pans and giving out the instantaneous temperature distribution of the corresponding shapes of the pans.The temperature distribution of the rectangular and circular pans proves that the product gets overcooked easily at the corners and edges of rectangular pans but not of a round pan.