煤油/氧气同轴离心喷嘴燃烧数值模拟

为了更好地了解同轴离心喷嘴的工作特性,基于DDES模型研究了油气比分别为0.5、1、1.5下以煤油/氧气为推进剂的喷嘴的流体动力学特性与非预混燃烧特征。研究结果表明:由于旋流离心作用,在喷嘴出口轴心处和燃烧室顶部分别存在一个驻定涡和角涡,驻定涡径向分布在0.9 R~1.4 R,轴向尺寸在-1 R~14 R,随着燃料流量增大,驻定涡会向喷嘴内部推进,并且径向尺寸也会扩大。燃烧计算结果表明,随着燃料流量增大,推进剂的掺混拖曳区变长、掺混效果变好;而由于油气比的增加,燃烧室更加富油因此燃烧温度有所下降,同时火焰前锋向喷嘴内移。

Effects of different combustion modes on the thermal efficiency and emissions of a diesel pilot-ignited natural gas engine under low-medium loads

Research on dual-fuel(DF)engines has become increasingly important as engine manufacturers seek to reduce carbon dioxide emissions.There are significant advantages of using diesel pilot-ignited natural gas engines as DF engines.However,different combustion modes exist due to variations in the formation of the mixture.This research used a simulation model and numerical simulations to explore the combustion characteristics of high-pressure direct injection(HPDI),partially premixed compression ignition(PPCI),and double pilot injection premixed compression ignition(DPPCI)combustion modes under a low-medium load.The results revealed that the DPPCI combustion mode provides higher gross indicated thermal efficiency and more acceptable total hydrocarbon(THC)emission levels than the other modes.Due to its relatively good performance,an experimental study was conducted on the DPPCI mode engine to evaluate the impact of the diesel dual-injection strategy on the combustion process.In the DPPCI mode,a delay in the second pilot ignition injection time increased THC emissions(a maximum value of 4.27g/(kW·h)),decreased the emission of nitrogen oxides(a maximum value of 7.64 g/(kW·h)),increased and then subsequently decreased the gross indicated thermal efficiency values,which reached 50.4%under low-medium loads.

Advances in LES of Two-phase Combustion(Ⅱ) LES of Complex Gas-Particle Flows and Coal Combustion

Large-eddy simulation(LES) is under its rapid development and is recognized as a possible second generation of CFD methods used in engineering.Large-eddy simulation of two-phase flows and combustion is particularly important for engineering applications.Some investigators,including the present authors,give their review on LES of spray combustion in gas-turbine combustors and internal combustion engines.However,up to now only a few papers are related to the state-of-the-art on LES of gas-particle flows and combustion.In this paper a review of the advances in LES of complex gas-particle flows and coal combustion is presented.Different sub-grid scale(SGS) stress models and combustion models are described,some of the main results are summarized,and some research needs are discussed.

Experimental Study on Emission Control of Premixed Catalytic Combustion of Natural Gas Using Preheated Air

In this paper the premixed catalytic combustion emissions such as CO, unburned hydrocarbon (UHC), NOx and the temperature distribution in the catalytic monolith with ultra low concentration of Pd were studied. Three types of monoliths were used for experiments and the temperature of preheated air was respectively 50℃ , 100℃ and 200℃ . The results showed that preheated air made radial temperature in the catalytic monolith uniform which helped to avoid local hot spots so as to decrease NOx emission. The experiment also proved that the shorter monolith showed much better catalytic combustion performance than longer one and the temperature at the exit of the shorter monolith was relatively lower. On the contrary, the temperature was higher in the longer monolith and the lethal NOx emission was slightly increased.

A back analysis of the temperature field in the combustion volume space during underground coal gasification

The exact shape and size of the gasification channel during underground coal gasification(UGC) are of vital importance for the safety and stability of the upper parts of the geological formation.In practice existing geological measurements are insufficient to obtain such information because the coal seam is typically deeply buried and the geological conditions are often complex.This paper introduces a cylindrical model for the gasification channel.The rock and soil masses are assumed to be homogeneous and isotropic and the effect of seepage on the temperature field was neglected.The theory of heat conduction was used to write the equation predicting the temperature field around the gasification channel.The idea of an excess temperature was introduced to solve the equations.Applying this model to UCG in the field for an influence radius,r,of 70 m gave the model parameters,u1,2,3...,of 2.4,5.5,8.7...By adjusting the radius(2,4,or 6 m) reasonable temperatures of the gasification channel were found for 4 m.The temperature distribution in the vertical direction,and the combustion volume,were also calculated.Comparison to field measurements shows that the results obtained from the proposed model are very close to practice.

Practical Paths towards Lowering Black Carbon Emissions

Black carbon （BC） aerosol, accounting for a minor fraction of atmospheric aerosols, is attracting increased attentio1 due to its impact on air quality, human health, and climate change. Focusing on BC emission reduction, this paper give1 a brief introduction to the sources and global distribution of BC. Along with the decrease of BC emissions from sue1 actions as the reduction of global greenhouse gases （GHGs） and regulating local air quality, it also highlights othet BC reduction approaches such as control and improvement of combustion conditions, the elimination of open biomas burning, and the sequestration of BC by biomass pyrolysis. Finally, it is stressed that at this moment there is no enougt reason to push BC reduction into any climate change related negotiations, although BC has been included in some o so-called win-win reduction targets for the quick response to both climate and non-climate appeals.

Experimental Study on Combustion Characteristics of Unused Biomasses in Compact Combustor

The aim of the present study is to develop the biomass furnace combustor which can effectively employ four unused biomasses, i.e., wood bark, wood branch, bamboo, and grass as a fuel. Emphasis is placed on the combustion gas components and combustion gas temperature in the combustor. It is found from the study that： （1） Four unused biomasses can take plate self combustion and the stable combustion yield; （2） Different combustion temperature distribution appears in combustor and is affected by each biomass; （3） The concentrations of nitrogen oxide and sulfur oxides are lower than the discharge standard value; （4） Higher thermal efficiency yields for bark, bamboo and grass.

Numerical Simulation of Tip Leakage Vortex Effect on Hydrogen-Combustion Flow around 3D Turbine Blade

In these years, a lot of environmental problems such as air pollution and exhaustion of fossil fuels have been discussed intensively. In our laboratory, a hydrogen-fueled propulsion system has been researched as an alternative to conventional systems. A hydrogen-fueled propulsion system is expected to have higher power, lighter weight and lower emissions. However, for the practical use, there exist many problems that must be overcome. Considering these backgrounds, jet engines with hydrogen-fueled combustion within a turbine blade passage have been studied. Although some studies have been made on injecting and burning hydrogen fuel from a stator surface, little is known about the interaction between a tip leakage vortex near the suction side of a rotor tip and hydrogen-fueled combustion. The purpose of this study is to clarify the influence of the tip leakage vortex on the characteristics of the 3-dimensional flow field with hydrogen-fueled combustion within a turbine blade passage. Reynolds-averaged compressible Navier-Stokes equations are solved with incorporating a k-ε turbulence and a reduced chemical mechanism models. Using the computational results, the 3-dimensional turbulent flow field with chemical reactions is numerically visualized, and the three-dimensional turbulent flow fields with hydrogen combustion and the structure of the tip leakage vortex are investigated.

MILD Combustion for Hydrogen and Syngas at Elevated Pressures

As gas recirculation constitutes a fundamental condition for the realization of MILD combustion, it is necessary to determine gas recirculation ratio before designing MILD combustor. MILD combustion model with gas recirculation was used in this simulation work to evaluate the effect of fuel type and pressure on threshold gas recirculation ratio of MILD mode. Ignition delay time is also an important design parameter for gas turbine combustor, this parameter is kinetically studied to analyze the effect of pressure on MILD mixture ignition. Threshold gas recirculation ratio of hydrogen MILD combustion changes slightly and is nearly equal to that of 10 MJ/Nm3syngas in the pressure range of 1-19 atm, under the conditions of 298 K fresh reactant temperature and 1373 K exhaust gas temperature, indicating that MILD regime is fuel flexible. Ignition delay calculation results show that pressure has a negative effect on ignition delay time of 10 MJ/Nm3syngas MILD mixture, because OH mole fraction in MILD mixture drops down as pressure increases, resulting in the delay of the oxidation process.

On the Controlling Factor of Catalyst Temperature in C_3H_8-Air Mixture

Catalytic combustion of propane-air mixture was investigated. Platinum catalysts over a flat stainless steel with γ- alumina washcoat were employed. The employed burner has three catalysts set parallel to the mixture flow, spaced at an interval of 5, 10 and 15 mm. Both experiment and numerical simulation were made at inlet temperature of 553 K, inlet velocity of 3 to 7 m/s and equivalence ratio of 0.3 to 0.5. In the numerical simulation, two-dimensional,. steady state model was developed to calculate the temperature and species concentration in gas-phase. In this model, chemical reaction on the catalyst surface and that in the gas phase were assumed to occur in three-steps. The numerical results show good agreement with experimental results. It was found that the properties of the catalyst strongly affect the catalyst surface temperature. Especially, the thermal conductivity of catalysthas a great effect, while the emissivity of catalyst has less effect.