气相化学法制备高硅铝比Y型沸石性能考宣传察

本研究以氮吸附、分析电镜（ＡＥＭ）、光电子能谱（ＥＳＣＡ）、固体核磁２９ＳｉＭＡＳＮＭＲ、２７ＡＩＭＡＳＮＭＲ及傅里叶红外（ＦＴ－ＩＲ）考察了用ＳｉＣｌ４气相化学法制备的高硅铝比Ｙ型沸石的吸附性能、孔结构、脱铝均匀性、硅铝分布及酸性，并对其催化剂进行了初步评价。结果表明，气相化学法可制备出晶胞参数变化范围宽、结晶保留度高的高硅铝比Ｙ型沸石，其骨架外铝以及二次孔均可调节。该沸石具有好的热稳定性和水热稳定性及良好的活性水平，适宜于作渣油催化裂化及提高汽油辛烷值的催化裂化催化剂的活性组元。

用气相化学法在铜合金上着古绿色

一、前言常用的金属着色方法有化学法、电化学法和热处理法等。大多数方法是使液体与金属表面直接接触,通过氧化而得到不同的颜色。用铜合金制成的艺术品常常需要着古绿色(绿锈)以达到仿真的效果。采用化学浸渍法或涂布法着古绿色有不同的处理规范,处理时间从数分钟到24 h。采用氯化铵、氨水、氯化钠混合液上色时,获得绿色的时间长,且不稳定,所获的色泽也不均匀,质量难以控制。本文利用氨水易于挥发的特点,采用气体与铜合金接触进行化学反应的方法着色,获得令人满意的效果。二、操作规范 1.工艺流程前处理→1号液酸洗→水洗→机械抛光→水洗→2号液酸洗→吸干酸液→涂染色液→置入密闭罩内与气体接触→工件翻面→局部抛光→置入密闭罩→水洗→干燥→喷涂透明保护漆→干燥。整个流程在室温下进行。

Microstructures and formation mechanism of headstand pyrocarbon cones developed by electromagnetic-field-assisted CVD

Novel headstand pyrocarbon cones （HPCs） with hollow structure were developed on the surfaces of pyrocarbon layers of the carbon/carbon （C/C） composites at 650-750 °C by the electromagnetic-field-assisted chemical vapor deposition in the absence of catalysts. The fine microstructures of the HPCs were characterized by high-resolution transmission electron microscopy. The results show that the textural features of the HPCs directly transfer from turbostratic structure in roots to a well-ordered high texture in stems. And the degree of high texture ordering decreases gradually from the stem to the tail of the HPCs. The formation mechanism of the HPCs was inferred as the comprehensive effect of polarization induction on electromagnetic fields and particle-filler property under disruptive discharge.

EFFECT OF GRID BIAS ON DEPOSITION OF NANOCRYSTALLINE DIAMOND FILMS

A positive grid bias and a negative substrate bias voltages are applied to the self-made hot filament chemical vapor deposited （HFCVD） system. The high quality nanocrystalline diamond （NCD） film is successfully deposited by double bias voltage nucleation and grid bias voltage growth. The Micro-Raman XRD SEM and AFM are used to investigate the diamond grain size, microstructure, surface morphology, and nucleation density. Results show that the obtained NCD has grain size of about 20 nm. The effect of grid bias voltage on the nucleation and the diamond growth is studied. Experimental results and theoretical analysis show that the positive grid bias increases the plasma density near the hot filaments, enhances the diamond nucleation, keeps the nanometer size of the diamond grains, and improves the quality of diamond film.

Effects of dip-coated BN interphase on mechanical properties of SiC_f/SiC composites prepared by CVI process

BN interphase was successfully synthesized on SiC fiber fabrics by dip-coating process using boric acid and urea as precursors under N2 atmosphere. The morphology of BN interphase was observed by SEM, and the structure was characterized by XRD and FT-IR spectra. The SiCf/SiC composites with dip-coated BN interphase were fabricated by chemical vapor infiltration （CVI） process, and the effects ofBN interphase on the mechanical properties of composites were investigated. The results show that the SiC fibers are fully covered by BN interphase with smooth surface and turbostratic structure （t-BN）, and the thickness is about 0.4 μm. The flexural strengths of SiCf/SiC composites with and without BN interphase are about 180 and 95 MPa, respectively. Compared with the as-received SiCf/SiC composites, the composites with BN interphase exhibit an obvious toughened fracture behavior. From the microstructural analysis, it can be confirmed that the BN interphase plays a key part in protecting the fibers from chemical attack during matrix infiltration and weakening interfacial bonding, which can improve the mechanical properties of SiCf/SiC composites remarkably.

Si-doped diamond films prepared by chemical vapour deposition

The effects of Si doping on morphology, components and structure characteristics of CVD diamond films were studied. Si-doped CVD diamond films were deposited on Si substrate by adding tetraethoxysilane （TEOS） into acetone as source of reactant gas. The morphology and microstructure of diamond films were characterized by scanning electron microcopy （SEM）. The crystalline quality of diamond films was studied by Raman spectroscopy and X-ray diffractometry （XRD）. The surface roughness of the films was evaluated with surface profilometer. The results suggest that Si doping tends to reduce the crystallite size, enhance grain refinement and inhibit the appearance of （11 I） facets. Raman spectra indicate that Si doping can enhance the formation of sp2 phase in diamond films. Moreover, Raman signal of SiC was detected, which suggests the existence of Si in the diamond films. Smooth fine-grained diamond （SFGD） film was synthesized at Si to C ratio of 1%.

Amorphous SiO_2 interlayers for deposition of adherent diamond films onto WC-Co inserts

Amorphous Si O2（a-Si O2） films were synthesized on WC-Co substrates with H2 and tetraethoxysilane（TEOS） via pyrolysis of molecular precursor.X-ray diffraction（XRD） pattern shows that silicon-cobalt compounds form at the interface between a-Si O2 films and WC-Co substrates.Moreover,it is observed by transmission electron microscope（TEM） that the a-Si O2 films are composed of hollow mirco-spheroid a-Si O2 particles.Subsequently,the a-Si O2 films are used as intermediate films and chemical vapor deposition（CVD） diamond films are deposited on them.Indentation tests were performed to evaluate the adhesion of bi-layer（a-Si O2 ＋ diamond） films on cemented carbide substrates.And the cutting performance of bi-layer（a-Si O2 ＋ diamond） coated inserts was evaluated by machining the glass fiber reinforced plastic（GFRP）.The results show that a-Si O2 interlayers can greatly improve the adhesive strength of diamond films on cemented carbide inserts;furthermore,thickness of the a-Si O2 interlayers plays a significant role in their effectiveness on adhesion enhancement of diamond films.

Determination of constituents of essential oil from Angelica sinensis by gas chromatographymass spectrometry

Gas chromatographymass spectrometry (GC-MS) coupled with chemometric resolution upon two- dimensional data was employed to analyze the constituents of essential oils of Angelica sinensis. Constituents in essential oils of Angelica sinensis root were identified by GC-MS with the help of subwindow factor analysis (SFA) method resolving two-dimensional original data into mass spectra and chromatograms. 76 of 97 separated constituents in essential oil of Angelica sinensis root were identified and quantified, and they account for about 91.36% of the total content. The results show that ligustilide, butylene phthalide, 2-methoxy-4-vinylphenol, carvacrol, allo-ocimene,2,6,6-trimethylbicyclo-[3,1,1]hept-2-ene are the main constituents in essential oil of Angelica sinensis root.

Chemical Composition of Essential Oil from Chimonanthus praecox Flower

Objective] To analyze the aroma constituents of essential oils from Chi-monanthus praecox. [Method] Extracted by microwave-assisted hydrodistil ation （MAHD）, aroma constituents of essential oils of Chimonanthus praecox flowers were analyzed by gas chromatography-mass spectrometry （GC-MS）. Normalization method was used to determine the constituents quantitatively. [Result] Total y 27 compounds were identified, accounting for 98.85% of total amounts. The main aroma con-stituents are terpenes, aldehydes, esters, alcohols and hydrocarbons. Main compo-nents with relative percentage over 5% are germacrene D （25.62%）, bornyl acetate （16.71%）, caryophyl ene （10.51%）, cis-α-ocimene （5.18%）, γ-elemene （8.05%）, β-linalool （5.01%）, 1-ethenyl-1-methyl-2,4-bis （1-methylethenyl）-cyclohexane （7.18%） and 2,3,4,4α,5,6-hexahydro-1,4αdimethyl-7-（1-methylethyl）-naphthalene （5.20%）. [Conclu-sion] The study provided a theoretical reference for the development and utilization of Chimonanthus praecox resources.

Technical Challenges and Progress in Fluidized Bed Chemical Vapor Deposition of Polysilicon

Various methods for production of polysilicon have been proposed for lowering the production cost andenergy consumption, and enhancing productivity, which are critical for industrial applications. The fluidized bed chemical vapor deposition （FBCVD） method is a most promising alternative to conventional ones, but the homogeneous reaction of silane in FBCVD results in unwanted formation of fines, which will affect the product qualityand output. There are some other problems, such as heating degeneration due to undesired polysilicon deposition on the walls of the reactor and the heater. This article mainly reviews the technological development on FBCVD of polycrystalline silicon and the research status for solving the above problems. It also identifies a number of challenges to tackle and principles should be followed in the design ofa FBCVD reactor.

Improved properties of carbon fiber paper as electrode for fuel cell by coating pyrocarbon via CVD method

The fabrication of a pyrocarbon coated carbon paper and its application to the gas diffusion lay(GDL) of proton exchange membrane(PEM) fuel cell were described.This carbon paper was fabricated by using conventional carbon paper as the precursor,and coating it with pyrocarbon by pyrolyzing propylene via the chemical vapor deposition(CVD) method.For comparison,conventional carbon paper composites were also prepared by using PAN-based carbon fiber felt as the precursor followed by impregnation with resin,molding and heat-treatment.SEM characterization indicates that pyrocarbon is uniformly deposited on the surface of the fiber in the pyrocarbon coated carbon paper and made the fibers of carbon felt bind more tightly.In contrast,there are cracks in matrix and debonding of fibers due to carbonization shrinkage in the conventional carbon paper.Property measurements show that the former has much better conductivity and gas permeability than the latter.In addition,current density-voltage performance tests also reveal that the pyrocarbon coating can improve the properties of carbon paper used for electrode materials of fuel cell.

Potential therapeutic significance of increased expression of aryl hydrocarbon receptor in human gastric cancer

AIM： To determine the functional significance of aryl hydrocarbon receptor （AhR） in gastric carcinogenesis, and to explore the possible role of AhR in gastric cancer （GC） treatment. METHODS： RT-PCR, real-time PCR, and Western blotting were performed to detect AhR expression in 39 GC tissues and five GC cell lines. AhR protein was detected by immunohistochemistry （IHC） in 290 samples： 30 chronic superficial gastritis （CSG）, 30 chronic atrophic gastritis （CAG）, 30 intestinal metapiasia （IN）, 30 atypical hyperplasia （AH）, and 70 GC. The AhR agonist tetrachlorodibenzo-para-dioxin （TCDD） was used to treat AGS cells. MTr assay and flow cytometric analysis were performed to measure the viability, cell cycle and apoptosis of AGS cells.RESULTS： AhR expression was significantly increased in GC tissues and GC cell lines. IHC results indicated that the levels of AhR expression gradually increased, with the lowest levels in CSG, followed by CAG, IM, AH and GC. AhR expression and nuclear translocation were significantly higher in GC than in precancerous tissues. TCDD inhibited proliferation of AGS cells via induction of growth arrest at the G1-S phase. CONCLUSION： AhR plays an important role in gastric carcinogenesis. AhR may be a potential therapeutic target for GC treatment.

Effect of Boundary Layers on Polycrystalline Silicon Chemical Vapor Deposition in a Trichlorosilane and Hydrogen System

This paper presents the numerical investigation of the effects of momentum, thermal and species boundary layers on the characteristics of polycrystalline silicon deposition by comparing the deposition rates in three chemical vapor deposition （CVD） reactors. A two-dimensional model for the gas flow, heat transfer, and mass transfer was coupled to the gas-phase reaction and surface reaction mechanism for the deposition of polycrystalline silicon from trichlorosilane （TCS）-hydrogen system. The model was verified by comparing the simulated growth rate with the experimental and numerical data in the open literature. Computed results in the reactors indicate that the deposition characteristics are closely related to the momentum, thermal and mass boundary layer thickness. To yield higher deposition rate, there should be higher concentration of TCS gas on the substrate, and there should also be thinner boundary layer of HCl gas so that HCl gas could be pushed away from the surface of the substrate immediately.

Characteristic evaluation of Al_2O_3/CNTs hybrid materials for micro-electrical discharge machining

The characteristic evaluation of aluminum oxide （A1203）/carbon nanotubes （CNTs） hybrid composites for micro-electrical discharge machining （EDM） was described. Alumina matrix composites reinforced with CNTs were fabricated by a catalytic chemical vapor deposition method. A1203 composites with different CNT concentrations were synthesized. The electrical characteristic of A1203/CNTs composites was examined. These composites were machined by the EDM process according to the various EDM parameters, and the characteristics of machining were analyzed using field emission scanning electron microscope （FESEM）. The electrical conductivity has a increasing tendency as the CNTs content is increased and has a critical point at 5% A1203 （volume fraction）. In the machining accuracy, many tangles of CNT in A1203/CNTs composites cause violent spark. Thus, it causes the poor dimensional accuracy and circularity. The results show that conductivity of the materials and homogeneous distribution of CNTs in the matrix are important factors for micro-EDM of A1203/CNTs hybrid composites.

Preparation of N-Doped TiO_2-Loaded Halloysite Nanotubes and Its Photocatalytic Activity under Solar-Light Irradiation

The N-doped TiO2-loaded halloysite nanotubes(N-Ti O2/HNTs) nanocomposites were prepared by using chemical vapor deposition method which was realized in autoclave. The photocatalytic activity of nanocomposites was evaluated by virtue of the decomposition of formaldehyde gas under solar-light irradiation. The XRD patterns verified that the anatase structured TiO2 was deposited on HNTs. The TEM images showed that the surface of HNTs was covered with nanosized TiO2 with a particle size of ca. 20 nm. The UV-vis spectra indicated that the N-Ti O2/HNTs presented a significant absorption band in the visible region between 400 nm and 600 nm. Under solar-light irradiation, the highest degradation rate of formaldehyde gas attained 90% after 100 min of solar-light irradiation. The combination of the photocatalytic property of TiO2 and the unique structure of halloysite would assert a promising perspective in degradation of organic pollutants.

Wear Behavior of Diamond-Coated Drawing Dies

The failure behavior of diamond-coated die was investigated experimentally and analytically through finite element method (FEM) simulation in the present work. Diamond coatings were fabricated by straight hot filament chemical vapor deposition (CVD) passing through the interior hole of the drawing die using a mixture of hydrogen and acetone as source gases. The performance tests were made under real drawing condition. Scanning electron microscopy (SEM) was used for the study of coating wear after die service. The coating wear appears on two regions of the reduction zone: one is near the entrance where the contact begins, and the other is at the end of the reduction zone. FEM simulation was made for calculating the von Mises stresses distribution on the coating and substrate during the drawing process. The present work was of great practical significance for the improvement of drawing performance of diamond-coated drawing dies.

Spectroscopic Analysis of Structural Transformation in Biodiesel Oxidation

The oxidation behavior of three biodiesels of different origins,viz.rapeseed oil derived biodiesel,soybean oil derived biodiesel and waste oil based biodiesel,were tested on an oxidation tester.The chemical compositions of the biodiesels were characterized by gas chromatography.Thereafter,the structural transformation of fatty acid methyl ester(FAME)of the biodiesels was analyzed by an infrared spectrometer and an ultraviolet absorption spectrometer.The results demonstrated that the oxidation behavior of biodiesels of different origins was closely related to the composition and distribution of FAMEs.Higher concentration of unsaturated FAME with multi-double bonds exhibited poorer oxidation resistance.Furthermore,cis-trans isomerization transformation occurred in the unsaturated FAME molecules and conjugated double-bond produced during the oxidation process of biodiesel.Greater cis-trans variations corresponded to deeper oxidation degree.The higher the content of unsaturated FAME with multi-double bonds in a biodiesel,the more the conjugated double bonds was formed.

Study on oil–source correlation by analyzing organic geochemistry characteristics: a case study of the Upper Triassic Yanchang Formation in the south of Ordos Basin, China

In the south of the Ordos Basin, the oil source of the Upper Triassic Yanchang Formation is confused all the time, which affects further exploration. In this study, oil sources from the oil layers of Ch6, Ch8 and Ch9 are all analyzed and confirmed. Through their carbon isotope value and biomarkers, characteristics of crude oils from the Yanchang Formation are analyzed. Then, the oil–source relation is discussed, with the source rocks' features.Finally, the oil–source relation is calculated through cluster analysis. It is believed that the oils from the Yanchang Formation deposit in a similar redox environment, with weak oxidation–weak reduction, and have all entered maturity stage. Ch9 crude oil is more mature than crude oils from Ch6 and Ch8, and has more advanced plants and fewer algae. Gas chromatography(GC) and gas chromatography–mass spectrometry(GC–MS) analysis show that crude oils from Ch6 and Ch8 may come from Ch7, and Ch9 crude oil may not. Cluster analysis displays that crude oils from Ch6 and Ch8 have closer squared Euclidean distance with Ch7 source rocks than Ch9 crude oil does,indicating crude oils from Ch6 and Ch8 stem from Ch7 source rocks. And Ch9 crude oil has rather close squared Euclidean distance with Ch9 source rocks, illustrating Ch9 crude oil may be from Ch9 source rocks. This research may provide the theoretical basis for the next exploration deploy in the south of Ordos Basin.

Assessing the kinetic model of hydro-distillation and chemical composition ofAquilaria malaccensis leaves essential oil

This study aimed to model the kinetic of hydro-distillation of Aquilaria malaccensis leaves oil in order to understand and optimize the extraction process. In addition, this study, for the first time, aimed to identify the chemical compositions of the A. rnalaccensis leave-oil. By assessing both first-order kinetic model and the model of simultaneous washing and diffusion, the result indicated that the model of simultaneous washing and diffusion better describes the hydro-distillation mechanism of the essential oil from A. rnalaccensis leaves. The optimum time, solid to liquid ratio, and the heating power for extracting the highest amount of essential oil were found to be around 3 h, 1：10 （g. ml-1）, and 300 W respectively. Yellow essential oil with a strong smell and a yield of 0.05 v/w was extracted by hydro-distillation Clevenger apparatus. Chemical compounds of the essential oil were analyzed using gas chromatography-mass spectroscopy （GC/MS）, which resulted in identification of 42 compounds that constitute 93% of essential oil. Among the identified components, Pentadecanal （32.082%）, 9-Octadecenal, （Z） （15.894%）, and Tetradecanal （6.927%） were the major compounds. Considering the fact that all the identified major components possess pesticidal properties, A. malaccensis leaves can be regarded as a promising natural source for producing pesticides.

Hydrophobic Ti_xO_y-C_mH_n Nanoparticle Film Prepared by Plasma Enhanced Chemical Vapor Deposition

The hydrophobic films of TixOy-CmHn. deposited from mixture gases of titanium isopropoxide （TTIP） and oxygen by plasma enhanced chemical vapor deposition （PECVD） were investigated. The films were investigated by scanning electron microscope （ SEM ）, transmission electron microscope （ TEM ）, Fourier transform infrared spectrometer （ FTIR）, X-Ray diffraction （ XRD ）, element analysis （ EA ）, ultraviolet visible spectrometer （ UV-Vis）, and water contact angle （WCA）. The results reveal that the surface of the films is formed by mierosized papillaes aggregated by inorganic and organic phases of complex nanoparticles with size from 50 nm to 200 nm when the discharge power is increased from 40 W to 150 W. All fdms demonstrate the strong broad of Ti-O-Ti stretching vibration at 400 -800cm-1, -CH bending vibration at 1 388 cm -1, and broadening -OH stretching vibration at 3 000-3500 cm-1 With the increase of the discharge power, the asdeposited film changes from amorphous to crystallization. The WCA of the film can be as high as 160°, indicating the hydrophobicity. The films show a similar ultraviolet absorption property as the bulk TiO2 film. The composition of the composition of film deposited at 150 W can be formulated as Tio.302-C1.5H3. Therefore, the composition formula of this hydrophobic film could be expressed as TiO2-C5H10O4.7. It is believed that the complex micro/nano structures of TiO2 and C5H10O4.7 residues are responsible for the observed hydrophobicity and the ultraviolet absorption property of the film.