几种 PVC 稳定剂的氧化光降解稳定作用及其协同效应

本文论述了二(硫代甘醇酸2—乙基己酯)二烷基锡(DOTG)结构对 PVC 稳定作用的影响,表明 Sn-C 键的稳定性和其对 PVC 热降解的稳定性之间的关系。DOTG热稳定剂对 PVC 的氧化光降解的稳定作用较差,本文还讨论了它与其它几种 PVC 稳定剂,如 DBTM、EBHPT、HOBP、BHBM 的协同效应。

Fabrication and photodegradation properties of TiO_2 nanotubes on porous Ti by anodization

Both Ti foil and porous Ti were anodized in 0.5%HF and in ethylene glycol electrolyte containing 0.5%NH4F(mass fraction) separately. The results show that TiO2 nanotubes can be formed on Ti foil by both processes, whereas TiO2 nanotubes can be formed on porous Ti only in the second process. The overhigh current density led to the failure of the formation nanotubes on porous Ti in 0.5%HF electrolyte. TiO2 nanotubes were characterized by SEM and XRD. TiO2 nanotubes on porous Ti were thinner than those on Ti foil. Anatase was formed when TiO2 nanotubes were annealed at 400 °C and fully turned into rutile at 700 °C. To obtain good photodegradation, the optimal heat treatment temperature of TiO2 nanotubes was 450 °C. The porosity of the substrates influenced photodegradation properties. TiO2 nanotubes on porous Ti with 60% porosity had the best photodegradation.

Synthesis and highly efficient photocatalytic activity of mixed oxides derived from ZnNiAl layered double hydroxides

ZnO/NiO/ZnAl2O4 mixed-metal oxides were successfully synthesized through a hydrotalcite-like precursor route, in which appropriate amounts of metal salts solutions were mixed to obtain a new series of ZnNiAl layered double hydroxides（LDHs） as precursors, followed by calcination under different temperatures. The as-obtained samples were characterized by SEM, HRTEM, TEM, XRD, BET, TG-DTA, and UV-Vis spectra techniques. The photocatalytic activities of the samples were evaluated by degradation of methyl orange（MO） under the simulated sunlight irradiation. The effects of Zn/Ni/Al mole ratio and calcination temperature on the composition, morphology and photocatalytic activity of the samples were investigated in detail. The results indicated that compared with ZnNiAl-LDHs, the mixed-metal oxide showed superior photocatalytic performance for the degradation of MO. A maximum of 97.3% photocatalytic decoloration rate within 60 min was achieved from the LDH with the Zn/Ni/Al mole ratio of 2：1：1 and the calcination temperature of 500 ℃, which much exceeded that of Degussa P25 under the same conditions. The possible mechanism of photocatalytic degradation over ZnO/NiO/ZnAl2O4 was discussed.

Strong visible absorption and excellent photocatalytic performance of brown TiO_2 nanoparticles synthesized using one-step low-temperature process

particle size （5.0 nm）, large specific surface area （213.45 m1 2/g）, and efficient response to broadband light over the entire ultraviolet-visible spectrum with a narrow band gap of 1.84 eV. In addition, TiO2 -180℃ exhibited the optimal reaction rate constant for the degradation of methylene blue （0.08287 mg/（Lmin））, which is six times higher than that of the mixed rutile/anatase phase TiO2 photocatalytic standard P25 （0.01342 mg/（L min））. Furthermore, cycling photodegradation ex-periments confirmed the stability and reusability of this catalyst. The unique physicochemical properties resulting from the low-temperature preparation of TiO2 -180℃, including its broadband visible absorption associated with a high concentration of oxygen vacancies, large surface area, and enriched surface -OH/H2O may be responsible for this excellent photocatalytic performance. The use of as-prepared TiO2 -180℃ for practical applications is expected after further optimization.

Photocatalytic Degradation of Water-Soluble Dyes by LaCoO_3

Pervoskite type oxides LaCoO 3 was prepared by citrate method with the granula of 20 nm-30 nm. With a fluorescent Hg lamp or sunlight as irradiator, the degradation experiments of various water soluble dyes were carried out in the suspension system of LaCoO 3 . The results show that the pervoskite type oxide LaCoO 3 has good photocatalytic activity.Studied by X ray photoelectron spectroscopy and photoacoustic spectra, its photocatalytic activity is found to be related with factors such as the d electron structure of ion Co 3+ ,Co—O binding energy and adsorbed oxygen on the surface etc.

Comparative Studies on Degradation of Methyl Orange by Nanostructured Zinc and Zinc Oxide Films

Nanostructured zinc and zinc oxide films were prepared by magnetron sputtering processes and succeeded air annealing treatments. Comparison of reductive degradation rate of methyl orange （MO） by zinc films and photocatalytic degradation rate of MO by zinc oxide films was carried out. Both reductive degradation and photocatalytic degradation process of MO by zinc and zinc oxide films can be described by first order kinetic model. It was found that although MO liquid was most quickly decolorized by metallic zinc films, the mineraliza- tion of MO was not thorough. Observation of extra ultraviolet absorption peaks indicated the formation of aromatic intermediates. On the other hand, although the photocatalytic degradation rate of MO liquid by ZnO films was only as about 1/4 large as the reductive degradation rate by zinc films, no signs of aromatic intermediates were found. Moreover, it was found that partially oxidized zinc oxide film showed higher photocatalytic efficiency than the totally oxidized ZnO films. Synergy effect between zinc and zinc oxide phase in the partially oxidized films was considered to be responsible for the higher photocatalytic efficiency.

Characterization of V_2O_5/MoO_3 composite photocatalysts prepared via electrospinning and their photodegradation activity for dimethyl phthalate

Vanadium pentoxide（V2O5）/molybdenum trioxide（MoO 3） composites with different molar ratios of vanadium（V） to molybdenum（Mo） were synthesized via a simple electrospinning technique. The photocatalytic activity of the composites were evaluated by their ability to photodegrade methylene blue and dimethyl phthalate（DMP） under visible-light irradiation. Compared with pure V2O5 and MoO 3,the V2O5/MoO 3 composites showed enhanced visible-light photocatalytic activity because of a V 3d impurity energy level and the formation of heterostructures at the interface between V2O5 and MoO 3. The optimal molar ratio of V to Mo in the V2O5/MoO 3 composites was found to be around 1/2. Furthermore,high-performance liquid chromatographic monitoring revealed that phthalic acid was the main intermediate in the photocatalytic degradation process of DMP.

Photocatalytic Degradation of Phenol over MWCNTs-TiO2 Composite Catalysts with Different Diameters

Titania-based composite catalysts were prepared through a sol-gel route employing multi-walled carbon nanotubes with different diameters. The materials were characterized using thermogravimetric analysis, nitrogen adsorption-desorption isotherm, powder X-ray diffraction, scanning electron microscopy, and diffuse reflectance UV-Vis absorption spectra. The application of the catalysts to photocatalytic degradation of phenol was tested under UV-Vis irradiation. A synergetic effect on phenol removal was observed in case of composite catalysts, which was evaluated in terms of apparent rate constant, total organic carbon removal and photonic efficiency.

Photocatalytic Degradation of Water-Soluble Dyes by LaCoO3

Pervoskite type oxides LaCoO 3 was prepared by citrate method with the granula of 20 nm-30 nm. With a fluorescent Hg lamp or sunlight as irradiator, the degradation experiments of various water soluble dyes were carried out in the suspension system of LaCoO 3 . The results show that the pervoskite type oxide LaCoO 3 has good photocatalytic activity.Studied by X ray photoelectron spectroscopy and photoacoustic spectra, its photocatalytic activity is found to be related with factors such as the d electron structure of ion Co 3+ ,Co—O binding energy and adsorbed oxygen on the surface etc.

Constructing 0D/1D Ag3PO4/TiO_(2) S-scheme heterojunction for efficient photodegradation and oxygen evolution

An S-scheme heterojunction photocatalyst is capable of boosting photogenerated carrier separation and transfer,thus maintaining high photooxidation and photoredox ability.Herein,a 0D Ag_(3)PO_(4) nanoparticles(NPs)/1D TiO_(2) nanofibers(NFs)S-scheme heterojunction with intimate interfacial contact was designed via the the hydro-thermal method.Benefiting from the abundant hydroxyl groups and size confinement effect of TiO_(2) NFs,the average diameter of the Ag_(3)PO_(4) nanoparticles decreased from 100 to 22 nm,which favored the construction of a 0D/1D geometry heterojunction.The multifunctional Ag_(3)PO_(4)/TiO_(2) sample exhibited excellent photocatalytic activity and stability in photocatalytic oxygen production(726μmol/g/h)and photocatalytic degradation of various organic contaminants such as rhodamine B(100%),phenol(60%)and tetracycline hydrochloride(100%).The significant improvements in the photocatalytic performance and stability can be attributed to the intimate interfacial contacts and rich active sites of 0D/1D geometry,fast charge carrier migration,and outstanding photoredox properties induced by the S-scheme charge-transfer route.This work offers a promising strategy for constructing 0D/1D S-scheme heterojunction photocatalysts for improved photocatalytic performance.

High photocatalytic activities of zinc oxide nanotube arrays modified with tungsten trioxide nanoparticles

Well‐aligned zinc oxide(ZnO)nanotube arrays loaded with tungsten trioxide(WO3)nanoparticles were synthesized by a process involving chemical bath deposition in combination with pyrolysis.The prepared ZnO–WO3composites were characterized by X‐ray diffraction,energy dispersive spectrometer,field emission scanning electron microscopy,X‐ray photoelectron spectroscopy,photoluminescence spectroscopy,Fourier transform infrared spectroscopy and UV–vis diffuse reflectance spectroscopy.The photocatalytic activities of the ZnO–WO3composite photocatalysts with different WO3contents for the degradation of the herbicide chlorinated phenoxyacetic acid(MCPA‐Na)under simulated sunlight irradiation were systematically evaluated.It was found that the WO3content had a great effect on the photocatalytic activity of the ZnO–WO3composites.The composite with3%WO3showed the highest photocatalytic activity,with a degradation rate of chlorinated phenoxyacetic acid of98.5%after200min with20mg of photocatalyst.This photodegradation rate was about twice that of the pristine ZnO nanotube array.The recombination of photogenerated electrons and holes was increasingly suppressed with the addition of WO3to ZnO.The high relative content of defects on the surface of the ZnO–WO3composites was beneficial to their photocatalytic activity in the degradation of chlorinated phenoxyacetic acid.?2018,Dalian Institute of Chemical Physics,Chinese Academy of Sciences.Published by Elsevier B.V.All rights reserved.

Pt/Bi_(24)O_(31)Cl_(10) composite nanosheets with significantly enhanced photocatalytic activity under visible light irradiation

Efficient composite semiconductor photocatalysts are highly desirable for the visible-light-driven degradation of organic pollutants. In this study, Bi24O31Cl10 photocatalyst was prepared via a hydrothermal method and modified with Pt nanoparticles (NPs) through a facile deposition procedure. The composite photocatalyst was characterized by X-ray diffraction, transmission electronic microscopy, X-ray photoelectron spectroscopy, UV-vis diffusion reflectance spectroscopy, photoluminescence spectroscopy, and electron spin resonance. The 1.0 wt% Pt/Bi24O31Cl10 photocatalyst showed the highest activity for the degradation of methyl orange under visible light (source: 300 W Xe lamp coupled with a UV-cutoff filter), and the photocatalytic degradation efficiency improved about 2.2 times compared to that of pure Bi24O31Cl10. The composite photocatalyst could maintain most of its activity after four runs of the photocatalytic experimental cycle. This study could provide a novel insight for the modification of other desirable semiconductor materials to achieve high photocatalytic activities.

Preparation of a p-n heterojunction BiFeO_3@TiO_2 photocatalyst with a core–shell structure for visible-light photocatalytic degradation

Magnetically separable bismuth ferrite(BiFeO3)nanoparticles were fabricated by a citrate self‐combustion method and coated with titanium dioxide(TiO2)by hydrolysis of titanium butoxide(Ti(OBu)4)to form BiFeO3@TiO2core-shell nanocomposites with different mass ratios of TiO2to BiFeO3.The photocatalytic performance of the catalysts was comprehensively investigated via photocatalytic oxidation of methyl violet(MV)under both ultraviolet and visible‐light irradiation.The BiFeO3@TiO2samples exhibited better photocatalytic performance than either BiFeO3or TiO2alone,and a BiFeO3@TiO2sample with a mass ratio of1:1and TiO2shell thickness of50-100nm showed the highest photo‐oxidation activity of the catalysts.The enhanced photocatalytic activity was ascribed to the formation of a p‐n junction of BiFeO3and TiO2with high charge separation efficiency as well as strong light absorption ability.Photoelectrochemical Mott-Schottky(MS)measurements revealed that both the charge carrier transportation and donor density of BiFeO3were markedly enhanced after introduction of TiO2.The mechanism of MV degradation is mainly attributed to hydroxyl radicals and photogenerated electrons based on energy band theory and the formation of an internal electrostatic field.In addition,the unique core-shell structure of BiFeO3@TiO2also promotes charge transfer at the BiFeO3/TiO2interface by increasing the contact area between BiFeO3and TiO2.Finally,the photocatalytic activity of BiFeO3@TiO2was further confirmed by degradation of other industrial dyes under visible‐light irradiation.

Preparation of amphiphilic TiO_2 Janus particles with highly enhanced photocatalytic activity

Stearic-acid-modified TiO2 (STA-TiO2) particles were prepared via the impregnation approach and used as a precursor for preparing TiO2 Janus particles. The morphology, structure, and properties of the TiO2 Janus particles were characterized using Fourier-transform infrared spectroscopy, ultraviolet- visible diffuse reflectance spectroscopy, thermogravimetric analysis, fluorescence microscopy, high-resolution transmission electron microscopy, contact angle analysis, dynamic light scattering, biological microscopy, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy measurements. The results show that TiO2 Janus particles can be successfully prepared via toposelective surface modification. STA grafted on the surface of TiO2 enhances its hydrophobicity, promotes charge separation, and improves its adsorption capacity for organic compounds. The TiO2 Janus particles strongly adsorb on an oil-water interface to form a stable Pickering emulsion. The degradation rates of high-concentration kerosene and nitrobenzene wastewaters when the photocatalyst is pure TiO2, STA-TiO2, or TiO2 Janus particles are discussed and compared. The degradation rates were determined using an ultraviolet-visible spectrophotometer. It was found that the Pickering emulsion stabilized by the TiO2 Janus particles exhibited the best photocatalytic performance;these Janus particles show promising potential for catalytic application.

Synthesis of novel p-n heterojunction m-Bi_2O_4/BiOCl nanocomposite with excellent photocatalytic activity through ion-etching method

A novel p‐n heterostructure photocatalyst m‐Bi2O4/BiOCl was successfully synthetized through a facile ion‐etching method.Via adjusting the added volume of HCl solution,a series of different ratios of composite photocatalysts were obtained.The as‐prepared samples of physical,chemical and optical characteristics were examined by X‐ray diffraction,scanning electron microscope,transmission electron microscope,energy dispersive X‐ray spectroscopy,selected‐area electron diffraction,Fourier transform infrared absorption,Raman microscope,N2 adsorption‐desorption,X‐ray photoelectron spectroscopy and UV‐vis spectrum technologies.The photocatalysts showed high degradation rate and complete mineralization ability for methyl orange and tetracycline solution under visible light.The reaction rate constant of m‐Bi2O4/BiOCl for methyl orange was 52.28 times higher than that of BiOCl.The characterization presented a good stability of materials.Furthermore,the photocurrent response test certified that the heterostructure effectively accelerated the separation and migration of photo‐generated carries.The scavenger experiments evidenced that hole(h+)and superoxide radical(?O2?)were the primary active radicals.A possible photocatalytic mechanism was proposed.This work provided an alternative photocatalyst applied to water environmental remediation.

Hydrogen producing water treatment through mesoporous TiO2 nanofibers with oriented nanocrystals

The development of well-defined TiO2 nanoarchitectures is a versatile strategy to achieve high-efficiency photocatalytic performance.In this study,mesoporous TiO2 nanofibers consisting of oriented nanocrystals were fabricated by a facile vapothermal-assisted topochemical transformation of preformed H-titanate nanobelts.The vapothermal temperature is crucial in tuning the microstructures and photocatalytic redox properties of the resulting mesoporous TiO2 nanofibers.The microstructures were characterized with XRD,TEM,XPS and nitrogen adsorption-desorption isotherms,etc.The photocatalytic activities were evaluated by photocatalytic oxidation of organic pollutant(Rhodamine B as an example)as well as photocatalytic reduction of water to generate hydrogen(H2).The nanofibers vapothermally treated at 150°C showed the highest photocatalytic activity in both oxidation and reduction reactions,2 times higher than that of P25.The oriented alignment and suitable mesoporosity in the resulting nanofiber architecture were crucial for enhancing photocatalytic performances.The oriented alignment of anisotropic anatase nanocrystals shall facilitate faster vectorial charge transportation along the nanofibers architecture.And,the suitable mesoporosity and high surface area would also effectively enhance the mass exchange during photocatalytic reactions.We also demonstrate that efficient energy-recovering photocatalytic water treatments could be accomplished by a cascading oxic-anoxic process where the dye is degraded in the oxic phase and hydrogen is generated in the successive anoxic phase.This study showcases a novel and facile method to fabricate mesoporous TiO2 nanofibers with high photocatalytic activity for both clean energy production and environmental purification.

Facile synthesis of hierarchical BiOCl_(x)Br_(1–x) solid solution with enhanced photocatalytic activity

The hierarchical BiOClxBr1–x was synthesized by a simple solvothermal method. The samples were characterized by X-ray diffraction （XRD）, field emission scanning electron microscopy （FESEM）, UV-visible diffuse reflectance spectroscopy （UV-vis DRS） and Brunauer-Emmett-Teller adsorption method. Compared to pure BiOCl or BiOBr, the BiOClxBr1–x solid solution has enhanced photocatalytic degradation activity for rhodamine B. This phenomenon can be explained to the hierarchical structure, lager specific surface area and appropriate energy gap of the obtained BiOClxBr1–x solid solution. The renewability and stability of photocatalyst were determinated and a possible mechanism of photocatalytic degradation was also proposed.

Fabrication of Z-scheme MoO3/Bi2O4 heterojunction photocatalyst with enhanced photocatalytic performance under visible light irradiation

Constructing Z-scheme heterojunction to improve the separation efficiency of photogenerated carriers of photocatalysts has gained extensive attention.In this work,we fabricated a novel Z-scheme MoO3/Bi2O4 heterojunction photocatalyst by a hydrothermal method.XPS analysis results indicated that strong interaction between MoO3 and Bi2O4 is generated,which contributes to charge transfer and separation of the photogenerated carriers.This was confirmed by photoluminescence(PL)and electrochemical impedance spectroscopy(EIS)tests.The photocatalytic performance of the as-synthesized photocatalysts was evaluated by degrading rhodamine B(RhB)in aqueous solution under visible light irradiation,showing that 15%MoO3/Bi2O4(15-MB)composite exhibited the highest photocatalytic activity,which is 2 times higher than that of Bi2O4.Besides,the heterojunction photocatalyst can keep good photocatalytic activity and stability after five recycles.Trapping experiments demonstrated that the dominant active radicals in photocatalytic reactions are superoxide radical( O2-)and holes(h+),indicating that the 15-MB composite is a Z-scheme photocatalyst.Finally,the mechanism of the Z-scheme MoO3/Bi2O4 composite for photo-degrading RhB in aqueous solution is proposed.This work provides a promising strategy for designing Bi-based Z-scheme heterojunction photocatalysts for highly efficient removal of environmental pollutants.

MXenes as noble-metal-alternative co-catalysts in photocatalysis

Photocatalysis has become a focal point in research as a clean and sustainable technology with the potential to solve environmental problems and energy crises.The loading of noble-metal co-catalysts can substantially improve the photocatalytic efficiency of semiconductors.Because the high cost and scarcity of noble metals markedly limit their large-scale applications,finding a noble-metal-alternative co-catalyst is crucial.MXene,a novel 2D transition metal material,has attracted considerable attention as a promising substitute for noble metal co-catalysts owing to its cost-efficiency,unique 2D layered structure,and excellent electrical,optical,and thermodynamic properties.This review focuses on the latest advancements in research on MXenes as co-catalysts in relatively popular photocatalytic applications(hydrogen production,CO2 reduction,nitrogen fixation,and organic pollutant oxidation).The synthesis methods and photocatalytic mechanisms of MXenes as co-catalysts are also summarized according to the type of MXene-based material.Finally,the crucial opportunities and challenges in the prospective development of MXene-based photocatalysts are outlined.We emphasize that modern techniques should be used to demonstrate the effects of MXenes on photocatalysis and that the photocatalytic activity of MXene-based photocatalysts can be further improved using defective engineering and recent phenomena such as the localized surface plasmon resonance effect and single-atom catalysis.

Autumn Photoproduction of Carbon Monoxide in Jiaozhou Bay, China

Carbon monoxide(CO) plays a significant role in global warming and atmospheric chemistry. Global oceans are net natural sources of atmospheric CO. CO at surface ocean is primarily produced from the photochemical degradation of chromophoric dissolved organic matter(CDOM). In this study, the effects of photobleaching, temperature and the origin(terrestrial or marine) of CDOM on the apparent quantum yields(AQY) of CO were studied for seawater samples collected from Jiaozhou Bay. Our results demonstrat that photobleaching, temperature and the origin of CDOM strongly affected the efficiency of CO photoproduction. The concentration, absorbance and fluorescence of CDOM exponentially decreased with increasing light dose. Terrestrial riverine organic matter could be more prone to photodegradation than the marine algae-derived one. The relationships between CO AQY and the dissolved organic carbon-specific absorption coefficient at 254 nm for the photobleaching study were nonlinear, whereas those of the original samples were strongly linear. This suggests that: 1) terrestrial riverine CDOM was more efficient than marine algae-derived CDOM for CO photoproduction; 2) aromatic and olefinic moieties of the CDOM pool were affected more strongly by degradation processes than by aliphatic ones. Water temperature and the origin of CDOM strongly affected the efficiency of CO photoproduction. The photoproduction rate of CO in autumn was estimated to be 31.98 μmol m-2 d-1 and the total DOC photomineralization was equivalent to 3.25%- 6.35% of primary production in Jiaozhou Bay. Our results indicate that CO photochemistry in coastal areas is important for oceanic carbon cycle.