A new clay-cement composite grouting material (CCGM) for tunnelling in underwater karst area was developed through the excellent synergistic interactions among cement, clay, meta-aluminate and lignin. The probable for...A new clay-cement composite grouting material (CCGM) for tunnelling in underwater karst area was developed through the excellent synergistic interactions among cement, clay, meta-aluminate and lignin. The probable formation mechanism of the material was proposed based on a series of experimental tests. The results show that with an optimal mass ratio (2:1:1:0.024) for water, cement, clay and additives, the obtained CCGM displayed an excellent grouting performance for karst in an underwater condition. Compared with neat cement grouts and clay-cement grouts, CCGM has faster gel time, lower bleeding rate and bulk shrinkage rate, greater initial viscosity, and a strong resistance to water dispersion. A successful engineering application indicates that CCGM not only fulfils a better grouting performance for karst in underwater conditions but also reduces the engineering cost and environmental pollution.展开更多
A series of centrifuge model tests exploring the effects of different types of slurry on long-trench stability in soft clay were conducted. The influence of groundwater conditions relative to trench stability was exam...A series of centrifuge model tests exploring the effects of different types of slurry on long-trench stability in soft clay were conducted. The influence of groundwater conditions relative to trench stability was examined by constructing long trenches using different slurries. The soil deformation and surface settlement induced by the excavation of the trench are found to be closely related to slurry type and excavation depth of the long trench. Increasing the bentonite concentration of the slurry has beneficial effects on stability: 1) larger particles can improve local and global stability in cases where filter cakes do not form, and 2) larger viscosity can promote filter cake formation on the walls of long trenches excavated in soft clay and enhance their stability.展开更多
To establish bonding stress—slip constitutive model between bars and grout concrete,13 test specimens were employed to study the bonding behavior and the force transfer of bars adhered to grout concrete. The bonding ...To establish bonding stress—slip constitutive model between bars and grout concrete,13 test specimens were employed to study the bonding behavior and the force transfer of bars adhered to grout concrete. The bonding stress development of bars adhered to grout concrete was analyzed. The local bonding stress—slip curve was obtained. Based on the test results,a new bonding stress— slip constitutive model between bars and grout concrete was proposed. The results show that the maximum bonding stress is not influenced by the bar bond length,but it is strengthened when the splitting strength of grout concrete is increased. The model matches the experimental results well,and the regressing coefficient equals 1.7.展开更多
The pull-out capacities for soil nailing systems comprising of one single 29 mm diameter(type A) and four 16 mm diameter(type B) rebars with grouted cement were examined.A field test and numerical analysis for the typ...The pull-out capacities for soil nailing systems comprising of one single 29 mm diameter(type A) and four 16 mm diameter(type B) rebars with grouted cement were examined.A field test and numerical analysis for the type A and type B systems were carried out to investigate the pull-out capacities and the slope stability reinforcement efficiency in soil and rock slopes.The results of the pull-out tests show the mobilized shear force and load transfer characteristics with respect to soil depth.The load-displacement relationship was examined for both type A and type B systems.Slope stability analyses were carried out to study the relationships between soil and nail reinforcement and bending stiffness as well as combined axial tension and shear forces.Factors of safety were calculated in relation to the number of nails and their outside diameters.Both soil and rock slopes were included in this evaluation.展开更多
During the hydration process, the Ultra-fine Cements present specific physical and chemical characteristics; they are, very short setting time and high heat release. For special applications, such as rapid hardening a...During the hydration process, the Ultra-fine Cements present specific physical and chemical characteristics; they are, very short setting time and high heat release. For special applications, such as rapid hardening and early high strength mortars or concretes, these characteristics can be considered advantageous. Some commercial products used for concrete reinforcement and repairs are the Rapid Hardening Mortars, these mortars must develop a time of setting up to 3 h and an initial compressive strength of about 3.5 MPa once the hardening of the paste is reached. The objective of the present research work is to use Ultra-fine Cement for the preparation of a series of different Rapid Hardening Mortars （with different percentages of Ultra-fine Cement）, these mortars required the addition of a polycarboxylate-base specification F Superplasticizer. It was observed that the optimum water/cement （W/C） ratio for the hydration of the Ultra-fine Cements is W/C = 0.385. The Ultra-fine Cements were obtained by the High Energy Ball-milling technique at laboratory scale, 90% of the Particle Size Distribution is below 11 μm and the Blaine Specific Surface Area is over 9000 cm^2/g.展开更多
Several studies focused on nutrients have shown that land use and management practices have a strong influence on stream chemistry. Much less is known about the relationship between heavy metal concentrations in strea...Several studies focused on nutrients have shown that land use and management practices have a strong influence on stream chemistry. Much less is known about the relationship between heavy metal concentrations in stream water and land use. We compared the variability of trace element concentrations in the stream of a catchment exposed to different types of management practices and land use. This is a small catchment with previous agricultural diffuse and accidental pollution mainly due to the spreading of slurry. The agricultural land was reforested in July 1998. The concentrations of Fe, Mn, Cu and Zn in dissolved phase from surface water samples collected at the catchment outlet were determined over a period of approximately six years. The results suggest that dissolved metal concentrations, especially Cu and Mn, are controlled by the land use and management practices. The median concentrations of studied metals were the highest in the agricultural period. It was also during this period when they all presented the highest concentration peaks, coinciding with a time of heavy application of manure to the soil. Dissolved Fe and Mn showed high dependence of flow rate, whereas Cu and Zn concentrations seemed to be independent of flow.展开更多
This investigation was carried out to study the effect of aggregate roughness on ITZ （interfacial transition zone） at same water/cement ratio and the influence of silica fume on the bond strength. On the experimenta...This investigation was carried out to study the effect of aggregate roughness on ITZ （interfacial transition zone） at same water/cement ratio and the influence of silica fume on the bond strength. On the experimental side, two types of aggregates （limestone and granite） were used, which were prepared with broken surface. Cement （Type I） was used with same w/c ratio for all batches. In order to study the effect of silica fume on the bond, the same mixes were produced with 8% silica fume. Three different tests were performed： ＂pull a part＂, Brazilian test and compressive strength test. The specimens for Brazilian and compressive strength were tested after 28 days, while the ＂pull a part＂ specimens were tested after 29 days. The result showed that the bond strength is influenced by the surface roughness of aggregate. For the same mix, limestone recorded higher bond strength than granite. Moreover, the bond strength is increased by adding the silica fume.展开更多
基金Project(51608539)supported by the National Natural Science Foundation of ChinaProjects(2016M592451,2017T100610)supported by the China Postdoctoral Science Foundation
文摘A new clay-cement composite grouting material (CCGM) for tunnelling in underwater karst area was developed through the excellent synergistic interactions among cement, clay, meta-aluminate and lignin. The probable formation mechanism of the material was proposed based on a series of experimental tests. The results show that with an optimal mass ratio (2:1:1:0.024) for water, cement, clay and additives, the obtained CCGM displayed an excellent grouting performance for karst in an underwater condition. Compared with neat cement grouts and clay-cement grouts, CCGM has faster gel time, lower bleeding rate and bulk shrinkage rate, greater initial viscosity, and a strong resistance to water dispersion. A successful engineering application indicates that CCGM not only fulfils a better grouting performance for karst in underwater conditions but also reduces the engineering cost and environmental pollution.
基金Project(41202220)supported by the National Natural Science Foundation of ChinaProject(20120022120003)supported by the Research Fund for the Doctoral Program of Higher Education,ChinaProject(2652012065)supported by the Fundamental Research Funds for the Central Universities and Beijing Higher Education Young Elite Teacher Program,China
文摘A series of centrifuge model tests exploring the effects of different types of slurry on long-trench stability in soft clay were conducted. The influence of groundwater conditions relative to trench stability was examined by constructing long trenches using different slurries. The soil deformation and surface settlement induced by the excavation of the trench are found to be closely related to slurry type and excavation depth of the long trench. Increasing the bentonite concentration of the slurry has beneficial effects on stability: 1) larger particles can improve local and global stability in cases where filter cakes do not form, and 2) larger viscosity can promote filter cake formation on the walls of long trenches excavated in soft clay and enhance their stability.
基金Project(2006BAJ03A01-05) supported by National Science and Technology Pillar Program during the 11th Five-Year Plan Period of ChinaProject (JG200705) supported by Key Laboratory of Structural Engineering of Shenyang Jianzhu University, China
文摘To establish bonding stress—slip constitutive model between bars and grout concrete,13 test specimens were employed to study the bonding behavior and the force transfer of bars adhered to grout concrete. The bonding stress development of bars adhered to grout concrete was analyzed. The local bonding stress—slip curve was obtained. Based on the test results,a new bonding stress— slip constitutive model between bars and grout concrete was proposed. The results show that the maximum bonding stress is not influenced by the bar bond length,but it is strengthened when the splitting strength of grout concrete is increased. The model matches the experimental results well,and the regressing coefficient equals 1.7.
文摘The pull-out capacities for soil nailing systems comprising of one single 29 mm diameter(type A) and four 16 mm diameter(type B) rebars with grouted cement were examined.A field test and numerical analysis for the type A and type B systems were carried out to investigate the pull-out capacities and the slope stability reinforcement efficiency in soil and rock slopes.The results of the pull-out tests show the mobilized shear force and load transfer characteristics with respect to soil depth.The load-displacement relationship was examined for both type A and type B systems.Slope stability analyses were carried out to study the relationships between soil and nail reinforcement and bending stiffness as well as combined axial tension and shear forces.Factors of safety were calculated in relation to the number of nails and their outside diameters.Both soil and rock slopes were included in this evaluation.
文摘During the hydration process, the Ultra-fine Cements present specific physical and chemical characteristics; they are, very short setting time and high heat release. For special applications, such as rapid hardening and early high strength mortars or concretes, these characteristics can be considered advantageous. Some commercial products used for concrete reinforcement and repairs are the Rapid Hardening Mortars, these mortars must develop a time of setting up to 3 h and an initial compressive strength of about 3.5 MPa once the hardening of the paste is reached. The objective of the present research work is to use Ultra-fine Cement for the preparation of a series of different Rapid Hardening Mortars （with different percentages of Ultra-fine Cement）, these mortars required the addition of a polycarboxylate-base specification F Superplasticizer. It was observed that the optimum water/cement （W/C） ratio for the hydration of the Ultra-fine Cements is W/C = 0.385. The Ultra-fine Cements were obtained by the High Energy Ball-milling technique at laboratory scale, 90% of the Particle Size Distribution is below 11 μm and the Blaine Specific Surface Area is over 9000 cm^2/g.
文摘Several studies focused on nutrients have shown that land use and management practices have a strong influence on stream chemistry. Much less is known about the relationship between heavy metal concentrations in stream water and land use. We compared the variability of trace element concentrations in the stream of a catchment exposed to different types of management practices and land use. This is a small catchment with previous agricultural diffuse and accidental pollution mainly due to the spreading of slurry. The agricultural land was reforested in July 1998. The concentrations of Fe, Mn, Cu and Zn in dissolved phase from surface water samples collected at the catchment outlet were determined over a period of approximately six years. The results suggest that dissolved metal concentrations, especially Cu and Mn, are controlled by the land use and management practices. The median concentrations of studied metals were the highest in the agricultural period. It was also during this period when they all presented the highest concentration peaks, coinciding with a time of heavy application of manure to the soil. Dissolved Fe and Mn showed high dependence of flow rate, whereas Cu and Zn concentrations seemed to be independent of flow.
文摘This investigation was carried out to study the effect of aggregate roughness on ITZ （interfacial transition zone） at same water/cement ratio and the influence of silica fume on the bond strength. On the experimental side, two types of aggregates （limestone and granite） were used, which were prepared with broken surface. Cement （Type I） was used with same w/c ratio for all batches. In order to study the effect of silica fume on the bond, the same mixes were produced with 8% silica fume. Three different tests were performed： ＂pull a part＂, Brazilian test and compressive strength test. The specimens for Brazilian and compressive strength were tested after 28 days, while the ＂pull a part＂ specimens were tested after 29 days. The result showed that the bond strength is influenced by the surface roughness of aggregate. For the same mix, limestone recorded higher bond strength than granite. Moreover, the bond strength is increased by adding the silica fume.
