纤维对水泥基复合材料阻裂性能的影响

添加纤维是控制水泥基复合材料裂缝的形成和扩展的最有效的方法之一。本文综述了目前国内外纤维对水泥基复合材料阻裂性能的研究进展,介绍了天然纤维、合成纤维、金属纤维、混杂纤维等对混凝土早期塑性收缩、干缩、温缩以及有害离子的侵入等引起的收缩的阻裂作用,讨论了阻裂性能和反应机理之间的关系,并指出了当前存在的问题及未来的研究重点和发展方向。

Experimental and numerical study on flexural behaviors of steel reinforced engineered cementitious composite beams

To investigate the flexural behaviors of steel reinforced engineered cementitious composite （ECC） beams, the behaviors of the steel reinforced ECC beam and the conventional steel reinforced concrete beam subjected to flexural load are experimentally compared. The experimental results show that the flexural strength and ductility of the steel reinforced ECC beam are 24.8% and 187.67% times larger than those of the steel reinforced concrete beam, and the substitution of concrete with ECC can significantly delay the propagation of cracks. Additionally, a simplified constitutive model of the ECC material is used to simulate the flexural behaviors of beams by the finite element analysis （FEA）. The results show a good agreement between the simulation and test results. The crack width of the steel reinforced ECC beam can be limited to 0.4 mm under the service load conditions. The application of ductile ECC can significantly increase the flexural performance in terms of flexural strength, deformation capacity and ductility of the beams.

Development of engineered cementitious composites with local ingredients

In order to reduce the cost of high performance polyvinyl alcohol（PVA） fiber reinforced cementitious material（called engineered cementitious composites,ECC）,a ductile ECC material is developed using domestic PVA fibers along with other local ingredients,such as fly ash,cement and sand.In addition to the economic analysis of ECC,the four-point bending test and the optical microscope are employed to investigate the deflection capacity of ECC,its crack width and the occurrence of the self-healing phenomenon.The experimental results suggest that ECC made with domestic ingredients exhibits larger deformability and the average crack width is controlled around 60 μm.Furthermore,the self-healing behavior is observed in cracks of the specimens after cycles of wet and dry curing.The economic analysis shows that the cost of ECC can be greatly reduced via employing domestic PVA fibers.It is,therefore,feasible to produce low cost ECC material employing domestic PVA fibers,while simultaneously retaining high material ductility.

PVA-ECC单轴抗压试验及本构关系

通过对6组不同配合比立方体试件进行单轴抗压试验,研究了高韧性聚乙烯醇水泥基复合材料(PVA-ECC)的抗压性能和抗压强度尺寸效应,测得了材料的单轴抗压强度和抗压应力应变曲线。试验结果表明,PVA-ECC抗压强度存在明显的尺寸效应,抗压强度随着尺寸边长的增大而减小。根据实测的应力应变曲线,提出了单轴受压本构模型,为PVA-ECC结构非线性有限元分析及结构设计提供了理论依据。

Fracture suppression at steel/concrete connection zones by ECC

In order to avoid brittle fracture failure, a ductile engineered cementitious composite （ECC） was attempted in steel/concrete connection zones to replace normal concrete. The influence of the ECC material ductility on connection failure modes and structural performance was investigated via the pushout test of stud/ECC connection, the pullout test of two-dimensional anchor bolt/ECC connection and the finite element modeling （FEM）. The experimental results suggest that the micromechanically designed ECC with a tensile ductility 300 times that of normal concrete switches the brittle fracture failure mode to a ductile one in steel connection zones. This modification in material behavior leads to higher load carrying capacity and structural ductility, which is also confirmed in FEM investigation. The enhancement in structural response through material ductility engineering is expected to be applicable to a wide range of engineering structures where steel and concrete come into contact.

Fracture Properties of Cement Composites Reinforced with Steel Polypropylene Hybrid Fibres

Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.

Flexural behaviors of double-reinforced ECC beams

In order to investigate the flexural behaviors of engineered cementitious composites （ECC）, theoretical and experimental researches are done on flexural doublereinforced ECC beams. Based on the assumption of the plane section remaining plane in bending and simplified constitutive models of materials, the calculation methods of load carrying capacities for different critical stages are obtained. Then, these calculation methods are demonstrated by comparing the test results with the calculation results. Finally, based on the proposed theoretical formulae, the effects of the compression strength, compression strain and tension strength of ECC, and the reinforcement ratio on the flexural behaviors of double-reinforced ECC beams are analyzed. The calculated and measured results are in good agreement, which indicates that the theoretical model can be used to predict the momentcurvature response of steel reinforced ECC beams. And the results of parametric studies show that the increase in the compression strength of ECC can greatly improve the flexural performance of beams; the increase in the ultimate compression strain can significantly improve the ultimate curvature and ductility, but has little effect on the load bearing capacity of beams. little effect on the flexural The tensile strength of ECC has behaviors of ECC beams. The increase in the steel reinforcement ratio can lead to significant improvement of the load bearing capacity and the stiffness of beams, but a degradation of the ductility of beams. The theoretical model and parameter analysis results in this paper are instructive for the design of steel reinforced ECC beams.

Mechanical behaviors of steel reinforced ECC / concrete composite columns under combined vertical and horizontal loading

In order to improve the load capacity, seismic performance and performance-cost ratio of the columns, the concrete at the base of reinforced concrete （RC） columns is substituted with engineered cementitious composites （ECC） to form ECC/RC composite columns. Based on the existing material properties, the mechanical behaviors of the ECC columns, ECC/RC composite columns and RC columns were numerically studied under combined vertical and horizontal loading with the software of ATENA. Then, the failure mechanism of ECC columns and ECC/RC composite columns were comprehensively studied and compared with that of the RC columns. Then, the effects of the height of the ECC, the axial compression ratio, and the transverse reinforcement ratio on the mechanical behaviors of the composite or the ECC column are studied. The calculation results show that the ultimate load capacity, ductility and crack resistance of the ECC or ECC/RC composite columns are superior to those of the RC columns. The ECC/RC composite column with a height of the ECC layer of 1.2h （ h is the height of the cross section） can achieve similar mechanical properties of a full ECC column. With high shear strength, ECC can undertake the shear force and significantly reduce the amount of stirrups, avoiding construction issues and promoting its engineering application.

Influence of different curing regimes on the microstructure and macro performance of UHPFRCC

This study investigates the influence of different curing regimes on the microstructure and macro properties of ultra-high performance fiber reinforced cementitious composite （UHPFRCC）, and aims to discover whether it is possible to produce qualified UHPFRCC using different curing regimes. A control mix of UHPFRCC is prepared. The mechanical performance and the short-term durability of the UHPFRCC matrix under three curing regimes are studied. In addition, the microstructures of the UHPFRCC matrix with different curing conditions are analyzed by combining scanning electron microscopy （SEM） and mercury intrusion porosimetry （MIP）. The results explore how different UHPFRCC curing regimes affect its microstructure and how the microstructure affects its macro behavior. Heat and steam curing for 3 d is succeeded to produce the UHPFRCC with nearly the same mechanical properties and durability as those of the 90 d standard curing. However, the heat cured UHPFRCC does not show great resistance to chloride-ion penetration.

Effect of graphene on mechanical properties of cement mortars

Functionalized graphene nano-sheets(FGN) of 0.01%-0.05%(mass fraction) were added to produce FGN-cement composites in the form of mortars. Flow properties, mechanical properties and microstructure of the cementitious material were then investigated. The results indicate that the addition of FGN decreases the fluidity slightly and improves mechanical properties of cement-based composites significantly. The highest strength is obtained with FGN content of 0.02% where the flexural strength and compressive strength at 28 days are 12.917 MPa and 52.42 MPa, respectively. Besides, scanning electron micrographs show that FGN can regulate formation of massive compact cross-linking structures and thermo gravimetric analysis indicates that FGN can accelerate the hydration reaction to increase the function of the composite effectively.

Seismic behaviors of steel reinforced ECC/RC composite columns under low-cyclic loading

To improve the seismic performance of columns, engineered cementitious composite （ECC） is introduced to partially substitute concrete at the base of the columns to form ECC,/reinforced concrete （ RC） composite columns. The mechanical behaviors of the ECC/RC composite columns are numerically studied under low-cyclic loading with the finite element analysis softwareof MSC. MARC. It is found that the ECC/RC composite columns can significantly enhance the load capacity, the ductility ad energy dissipation of columns. Then, the effects of the height of the ECC, the axial compression ratio and the longitudinal reinforcement ratio on the seismic behaviors of the composite columns are parametrically studied. The results show that the ECC/RC composite column with a height of the ECC layer of 0. Sh（h is the height to the cross-section） can achieve similar seismic performance of a full ECC column. The peak load of the composite column increases significantly while the ductility decreases with the increase of the axial compression ratio. Increasing the longitudinal reinforcement ratio within a certain range can improve the ductility and energy dissipation capacity and almost has no effect on load capacity. The aalysis results ae instructive and valuable for reference in designing ECC structures.

Flexural response of reinforced concrete beams strengthened with post-poured ultra high toughness cementitious composites layer

Four-point bending tests were conducted up to failure on eleven reinforced concrete (RC) beams and strengthening beams to study the effectiveness of externally pouring ultra high toughness cementitious composites (UHTCC) on improving the flexural behavior of existing RC beams.The strengthening materials included UHTCC and high strength grade concrete.The parameters,such as thickness and length of strengthening layer and reinforcement in post-poured layer,were analyzed.The flexural behavior,failure mode and crack propagation of composite beams were investigated.The test results show that the strengthening layer improves the cracking and ultimate load by increasing the cross section area.Introducing UHTCC material into strengthening not only improves the bearing capacity of the original specimens,but also disperses larger cracks in upper concrete into multiple tightly-spaced fine cracks,thus prolonging the appearance of harm surface cracks and increasing the durability of existing structures.Compared with post-poured concrete,UHTCC is more suitable for working together with reinforcement.The load?deflection plots obtained from three-dimensional finite-element model (FEM) analyses are compared with those obtained from the experimental results,and show close correlation.

Effects of superabsorbent polymer particles on flexural properties and self-healing behavior of ECC

In order to improve the self-healing behavior and the recovery of mechanical properties of engineered cementitious composites(ECC),the approach of incorporating superabsorbent polymer(SAP)in mixtures is investigated.The rapid water penetration test and four-point bending test were conducted to evaluate the effects of self-healing on the water permeability and mechanical properties of pre-damaged ECC.The self-healing process and self-healing products were observed by the environment scanning electron microscope(ESEM)and energy dispersive X-ray spectroscopy(EDS).The experimental results show that all ECC mixtures exhibit excellent flexural capacity,meanwhile maintaining a crack width below 50μm.The incorporation of SAP particles in ECC can apparently improve the mechanical recovery of ECC mixtures after 10 healing curing cycles,such as flexural deformation and flexural stiffness.The flexural stiffness of ECC containing 4%SAP particles after self-healing can be recovered to 80%.The self-healing test results show that when the water permeability of ECC mixtures incorporating SAP particles is close to zero,only three healing cycles are needed.When ECC incorpora ting more SAP particles,the accelerated self-healing process can be finished in the first three cycles,and self-healing product is mixed Ca(OH)2/CaCO 3 with CaCO 3 being a major component in the later stage.It is,therefore,feasible to produce ECC materials incorporating SAP particles,while simultaneously maintaining higher material ductility and self-healing behavior.

Mechanical properties of polyvinyl alcohol-basalt hybrid fiber engineered cementitious composites with impact of elevated temperatures

In the present study,the mechanical properties of polyvinyl alcohol(PVA)-basalt hybrid fiber reinforced engineered cementitious composites(ECC)after exposure to elevated temperatures were experimentally investigated.Five temperatures of 20,50,100,200 and 400℃ were set to evaluate the residual compressive,tensile and flexural behaviors of hybrid and mono fiber ECC.It was shown that partial replacement of PVA fibers with basalt fibers endowed ECC with improved residual compressive toughness,compared to brittle failure of mono fiber ECC heated to 400℃.The tension tests indicated that the presence of basalt fibers benefited the tensile strength up to 200℃,and delayed the sharp reduction of strength to 400℃.Under flexural load,the peak deflections corresponding to flexural strengths of hybrid fiber ECC were found to be less vulnerable ranging from 20 to 100℃.Further,the scanning electron microscopy(SEM)results uncovered that the rupture of basalt fiber at moderate temperature and its pullout mechanism at high temperature was responsible for the mechanical evolution of hybrid fiber ECC.This work develops a better understanding of elevated temperature and basalt fiber impact on the residual mechanical properties and further provides guideline for tailoring ECC for improved fire resistance.

Flexural behavior of steel reinforced engineered cementitious composite beams

In order to enhance the durability of steel encased concrete beams, a new type of steel reinforced engineered cementitious composite(SRECC) beam composed of steel shapes, steel bars and ECC is proposed. The theoretical analyses of the SRECC beam including crack propagation and stress-strain distributions along the depth of the composite beam in different loading stages are conducted. A theoretical model and simplified design method are proposed to calculate the load carrying capacity. Based on the proposed theoretical model, the relationship between the moment and corresponding curvature is derived. The theoretical results are verified with the finite element analysis. Finally, an extensive parametric study is performed to study the effect of the matrix type, steel shape ratio, reinforced bar ratio, ECC compressive strength and ECC tensile ductility on the mechanical behavior of SRECC beams. The results show that substitution concrete with ECC can effectively improve the bearing capacity and ductility of composite beams. The steel shape and longitudinal reinforcement can enhance the loading carrying capacity, while the ductility decreases with the increase of steel shape ratio. ECC compressive strength has significant effects on both load carrying capacity and ductility, and changing the ultimate strain of ECC results in a very limited variation in the mechanical behavior of SRECC beams.

Deformation behavior of high performance fiber reinforced cementitious composite prepared with asphalt emulsion

A novel engineered cementitious composite(ECC) was prepared with the complex binder of Portland cement and asphalt emulsion.By adjusting the amount of asphalt emulsion,different mixture proportions were adopted in experiments,including four-point bending test,compressive test,and scanning electric microscopy(SEM).The SEM observation was conducted to evaluate the contribution of polyvinyl alcohol(PVA) fiber and asphalt emulsion to the composite toughening mechanism.The tests results show that the most remarkable deflection-hardening behavior and saturated multiple cracking are achieved when the content of asphalt emulsion is 10%.However,excessive content of asphalt emulsion causes severe damages on the deformation behavior as well as loss in compressive strength of the mixture.SEM observation indicates that the influence of asphalt emulsion on the fiber/matrix interfacial property changes the dominant fiber failure type from rupture into pull-out mode,and thus causes beneficial effects for strain-hardening behavior.

Main properties of ultra-high performance fiber reinforced cement composites under couple effect of load and environment

This study aims to reveal the mechanism that how the content of steel fibers and strength grades affect the macro performance of the ultra-high performance fiber reinforced cementitious composite （UHPFRCC） and to study the UHPFRCC durability under the combined effect of loads and environments. Three types of high and ultra-high performance fiber reinforced cement composites with different strength grades （100, 150, 200 MPa） and different steel fiber volume fractions （0%, 1%, 2%, 3%） are prepared. The main properties of mechanical performance and short-term durability are studied. A preloading frame is designed to apply a four- point load external flexural stress with a stress selection ratio of 0.5 for UHPFRCC150 specimens. The results show that the growth in strength grade with a proper content of steel fiber greatly increases the strength and toughness of the HPFRCC and the UHPFRCC while decreasing the dry-shrinkage ratio. For the loaded specimens, the existence of steel fiber can reduce the negative influence of tensile stress on the Cl- penetration resistance of the UHPFRCC in addition to improving its ability to resist the freeze-thaw damage.

A uniaxial tensile constitutive equation of high-ductility cementitious composites

In order to establish the constitutive relationship of high-ductility cementitious composites(HDCCs)under uniaxial tensile load and to guide the structural design of HDCCs,based on the analysis of the existing uniaxial tensile constitutive relationship and ideal elastoplastic linear strain-hardening model,a bilinear tensile constitutive equation of HDCCs was proposed.The points of nominal initial cracking and nominal maximum stress were adopted as control points of the line segment,and the constitutive relationship of HDCCs was established.Five series of uniaxial tensile stress-strain curves of HDCCs were combined to perform an experimental application of the constitutive equation,along with an analysis of the key parameters.The experimental results confirm the ability of the constitutive equation to overcome the problem of insufficient or excessive redundancy of existing models in terms of calculation bearing capacity.Specifically,the measured maximum stress value is larger than the nominal value,and the ratio between the two values ranges from 1.08 to 1.22.Additionally,the tensile strain at the softening point obtained by fitting a straight line with the valley points of the strain-hardening stage curve is greater than or equal to the tensile strain at the measured maximum stress point and the ratio of the fitted values to the measured values ranges from 1.00 to 1.19.

Effects of curing age on compressive and tensile stress-strain behaviors of ecological high ductility cementitious composites

To obtain the design parameters of the structure made by ecological high ductility cementitious composites(Eco-HDCC),the effects of curing age on the compressive and tensile stress-strain relationships were studied.The reaction degree of fly ash,non-evaporable water content and the pH value in pore solution were calculated to reveal the mechanical property.The results indicate that as the curing age increases,the peak compressive strength,peak compressive strain and ultimate tensile strength of Eco-HDCC increase.However,the ultimate compressive strain and ultimate tensile strain of Eco-HDCC decrease with the increase in curing age.Besides,as the curing age increases,the reaction degree of fly ash and non-evaporable water content in Eco-HDCC increase,while the pH value in the pore solution of Eco-HDCC decreases.Finally,the simplified compressive and tensile stress-strain constitutive relationship models of Eco-HDCC with a curing age of 28 d were suggested for the structure design safety.

Electrocaloric behavior of Ba_(0.85)Ca_(0.15)Zr_(0.1)Ti_(0.88)Sn_(0.02)O_3 cement composites

A thrust for looking multifunctional materials for applications in civil engineering structures has attracted interest among researchers across the globe.Cement based Ba0.85Ca0.15Zr0.1Ti0.88Sn0.02O3(BCZT.Sn)composites were prepared for electrocaloric applications with varying BCZT.Sn to cement ratio.Hysteresis loops showed some signature of saturation in cement composites.However,loops of pure sample were saturated due to its ferroelectric nature.Furthermore,these composites were explored for the first time in solid state refrigeration technology namely electrocaloric effect(ECE).Peak electrocaloric performance shows an adiabatic temperature changes of 0.71,0.64 and 0.50 K and isothermal entropy changes of 0.86,0.80 and 0.65 J/(kg.K)for BCZT.Sn,10%and 15%cement composites,respectively,under application of 0-29 kV/cm electric field.The adiabatic temperature change in cement based composites is comparable with that of the BCZT-Sn ferroelectric ceramics.Furthermore,the dielectric constant(εr)of composites with different ceramic contents at room temperature reveals that dielectric constant increases with an increase in BCZT-Sn proportion in composites.These cement based BCZT.Sn composite materials may be used in solid state refrigeration as they are fairly competitive with the pristine sample.