明溪蓝刚玉的水热溶液改色实验初步研究

明溪蓝刚玉中 Fe主要以 Fe3 + 形式存在 ,Fe3 + 的 d- d电子跃迁和 Fe2 + - Ti4 + / Fe3 + -Ti3 + 、O2 - Fe3 + 间电荷转移是致色的主要因素 ;浓度差可以作为扩散动力 ;氢含量的提高可以促进蓝色致色因子的形成。采用高温高压水热溶液方法对蓝刚玉进行改色处理 ,可消除刚玉中的杂色调 ,使颜色向纯蓝色方向变化。

水热盐溶液卸压法制备氧化物粉体

本文采用一种新的水热粉体制备方法-水热盐溶液卸压法，制得了α-Al2O3粉体、AlO（OH）纤维以及ZrO2和AlO（OH）复合氧化物粉体．发现以1mol／LAl（NO3）3溶液作为前驱物，0．2mol／LFe（NO3）3为添加剂，在300℃可制得α－Al2O3粉体．以1mol／LAl（NO3）3溶液为前驱物；1mol／LKBr为添加剂，在350℃可制得长径比为13：1的AlO（OH）纤维．当采用AlCl3、ZrOCl2溶液为前驱物，Zr/Al的比例为1：3时，在240℃可制得纤维状AlO(OH)颗粒和球形ZrO2颗粒的复合氧化物粉体．

The Swelling Equilibria of N-isopropylacrylamide Based Hydrogel in Aqueous Solution of Ethanol

N-isopropylacrylamide (NIPAAm) was used to synthesize NIPAAm homopolymer (nonionized) and NIPAAm-sodium methacrylate copolymer (ionized). The swelling equilibria for both gels were obtained in aqueous solution of ethanol with concentration ranging from 0 to 100%(by mass) at 25℃. The swollen gel in water shrank first with the addition of a small amount of ethanol and then reswelled with further addition of ethanol showing not only a discontinuous volume phase transition but also a typical reentrant phenomenon. A thermodynamic model based on the UNIQUAC with the 'free-volume' contribution was applied to correlate and predict the swelling behavior of the poly(NIPAAM)-gels in ethanol-water mixture.

Synthesis of ZnO whiskers via hydrothermal decomposition route

ZnO whiskers with a length of 30-40μm and a diameter of about 1μm were synthesized by co-precipitation of ZnSO 4 and Na2CO3 solution at room temperature followed by hydrothermal treatment of the as-prepared Zn5(CO3)2(OH)6 precursor at 160 ℃for 6 h.The increase of the initial solution pH promotes the hydrothermal conversion of the particulate Zn5(CO3)2(OH)6 to ZnO whiskers.The presence of minor amount of EDTA in the hydrothermal solution promotes the one dimensional growth of ZnO whiskers,leading to the formation of ZnO whiskers with a length of 50-60μm and a diameter of 1-2μm.

Adsorption of dimethyl trisulfide from aqueous solution on a low-cost adsorbent:thermally activated pinecone

Thermally activated pinecone(TAP) was used for the adsorption of dimethyl trisulfide(DMTS)from aqueous solutions,which was proved to be the main odorous in algae-caused black bloom.The effects of adsorbent dosage,adsorbate concentration and contact time on DMTS biosorption were studied.The TAP produced at 600℃ exhibited a relatively high surface area(519.69 m^2/g) and excellent adsorption capacity.The results show that the adsorption of DMTS was initially fast and that the equilibrium time was6 h.Higher initial DMTS concentrations led to lower removal percentages but higher adsorption capacity.The removal percentage of DMTS increased and the adsorption capacity of TAP decreased with an increase in adsorbent dosage.The adsorption process conforms well to a pseudo-second-order kinetics model.The adsorption of DMTS is more appropriately described by the Freundlich isotherm(R^2=0.996 1) than by the Langmuir isotherm(R^2=0.916 9).The results demonstrate that TAP could be an attractive low-cost adsorbent for removing DMTS from water.

Influence factors on thermal conductivity of ammonia-water nanofluids

In order to investigate the mechanism of nanoparticles enhancing the heat and mass transfer of the ammonia-water absorption process,several types of binary nanofluids were prepared by mixing Al2O3 nanoparticles with polyacrylic acid(PAA),TiO2 with polyethylene glycol(PEG 1000),and TiN,SiC,hydroxyapatite(noodle-like) with PEG 10000 to ammonia-water solution,respectively.The thermal conductivities were measured by using a KD2 Pro thermal properties analyzer.The influences of surfactant and ammonia on the dispersion stabilities of the binary nanofluids were investigated by the light absorbency ratio index methods.The results show that the type,content and size of nanoparticles,the temperature as well as the dispersion stability are the key parameters that affect the thermal conductivity of nanofluids.For the given nanoparticle material and the base fluid,the thermal conductivity ratio of the nanofluid to the ammonia-water liquid increases as the nanoparticle content and the temperature are increased,and the diameter of nanoparticle is decreased.Furthermore,the thermal conductivity ratio increases significantly by improving the stabilities of nanofluids,which is achieved by adding surfactants or performing the proper ammonia content in the fluid.

Hydrothermal Liquefaction of Wheat Straw in Sub-critical Water/Ethanol with Ionic Liquid for Bio-oil Production

Hydrothermal liquefaction of wheat straw in sub-critical water with ionic liquid was investigated in an autoclave. The product distribution at different temperatures and pressures was studied. The liquid oil and the residuals were tested by 1H NMR, FTIR and SEM techniques. The results indicated that under the same conditions, the oil yield from liquefaction of wheat straw in water/ethanol was higher than that in sub-critical water. The result also showed that under the investigated conditions, adding 1-butyl-3-methylimidazolium chloride([Bmim]Cl) could increase the total conversion and gas yield, while at the same time the yield of n-hexane insoluble fraction and the tetrahydrofuran soluble fraction was reduced. Moreover, the results also showed that upon adding [Bmim]Cl the contents of the aliphatic hydrogen and phenols in liquid oil also increased along with improved oil quality.

Correlation of ^1H NMR Chemical Shift for Aqueous Solutions by Statistical Associating Fluid Theory Association Model

1H NMR chemical shifts of binary aqueous mixtures of acylamide, alcohol, dimethyl sulphoxide (DMSO), and acetone are correlated by statistical associating fluid theory (SAFT) association model. The comparison between SAPT association model and Wilson equation shows that the former is better for dealing with aqueous solutions. Finally, the specialties of both models are discussed.

Influence of welding speed on corrosion behaviour of friction stir welded AA5086 aluminium alloy

The plates of AA5086 aluminium alloy were joined together by friction stir welding at a fixed rotation speed of 1000 r/min various welding speeds ranging from 63 to 100 mm/min.Corrosion behavior of the parent alloy(PA),the heat affected zone(HAZ),and the weld nugget zone(WNZ)of the joints were studied in 3.5%(mass fraction)aerated aqueous Na Cl solution by potentiodynamic polarization and electrochemical impedance spectroscopy(EIS).The corrosion susceptibility of the weldments increases when the welding speed increases to 63 and 100 mm/min.However,the value of corrosion rate in the weldments is lower than that in the PA.Additionally,the corrosion current density increases with increasing the welding speed in the HAZ and the WNZ.On the contrary,the corrosion potential in the WNZ appears more positive than in the HAZ with decreasing the welding speed.The WNZ exhibits higher resistance compared to the HAZ and the PA as the welding speed decreases.The results obtained from the EIS measurements suggest that the weld regions have higher corrosion resistance than the parent alloy.With increasing the welding speed,the distribution and extent of the corroded areas in the WNZ region are lower than those of the HAZ region.In the HAZ region,in addition to the pits in the corroded area,some cracks can be seen around the corroded areas,which confirms that intergranular corrosion is formed in this area.The alkaline localized corrosion and the pitting corrosion are the main corrosion mechanisms in the corroded areas within the weld regions.Crystallographic pits are observed within the weld regions.

Adsorption of Pb^(2+) on macroporous weak acid adsorbent resin from aqueous solutions: Batch and column studies

The adsorption properties of a novel macroporous weak acid resin （D152） for Pb^2＋ were investigated with chemical methods. The optimal adsorption condition of D152 resin for Pb^2＋ is at pH 6.00 in HAc-NaAc medium. The statically saturated adsorption capacity is 527 mg/g at 298 K. Pb^2＋ adsorbed on D152 resin can be eluted with 0.05 mol/L HCI quantitatively. The adsorption rate constants determined under various temperatures are k288 n=2.22×10-5 s^-1, k298 K=2.51 × 10^-5 s^-1, and k308 K= 2.95 × 10^-5 s^-1, respectively. The apparent activation energy, Ea is 10.5 kJ/mol, and the adsorption parameters of thermodynamics are ΔH^Θ=13.3 kJ/mol, ΔS^Θ=119 J/（mol·K）, and ΔG^Θ298 K =-22.2 kJ/mol, respectively. The adsorption behavior of D152 resin for Pb^2＋ follows Langmuir model.

Preparation of Magnesium Oxide Whisker by MgSO4·5Mg（OH）2·2H2O Whisker ＂Pseudomorph＂ Technique

To promote the scale-up production and industrial application of magnesium oxide （MgO） whiskers, MgO whiskers were prepared by the calcination method of the precursor. The precursor MgSO4·5Mg（OH）2·2H2O （152 MOS） single component was prepared by hydrothermal synthesis reaction in MgSO4 solution and NaOH solution. MgO whisker was prepared by heating treatment of the precursor at low heating speed to keep the structure of the precursor not be destroyed. The composition, the morphology and the structure of these whiskers were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The results indicate that the MgO whisker was about 0.5-1.2 μm in diameter and 20-80 μm in length, with an aspect ratio no less than 100.