期刊文献+
共找到4篇文章
< 1 >
每页显示 20 50 100
水磨泥合金粉的凝胶注模成形工艺研究
1
作者 车晓舟 《粉末冶金工业》 CAS 北大核心 2024年第1期84-88,共5页
将刀具生产过程中产生的水磨泥钢粉分离、净化,通过添加适量合金元素配成水磨泥合金粉。采用甲基丙烯酸羟乙酯作单体、三缩四乙二醇双丙稀酸酯作交联剂,用凝胶注模成形方法将水磨泥合金粉成形,经脱模、干燥和1 400℃、2 h烧结后得到烧结... 将刀具生产过程中产生的水磨泥钢粉分离、净化,通过添加适量合金元素配成水磨泥合金粉。采用甲基丙烯酸羟乙酯作单体、三缩四乙二醇双丙稀酸酯作交联剂,用凝胶注模成形方法将水磨泥合金粉成形,经脱模、干燥和1 400℃、2 h烧结后得到烧结坯,烧结坯组织由珠光体、碳化物和微孔洞组成。烧结坯经1 050℃淬火、180℃回火热处理,硬度为50HRC。经浓度5%氯化钠水溶液3 h盐雾测试,热处理后的烧结坯的腐蚀程度远低于未热处理的烧结坯,表明水磨泥合金粉烧结坯经淬火、低温回火后具有良好的耐蚀性能。 展开更多
关键词 凝胶注模成形 水磨泥 不锈钢 烧结 耐蚀性能
原文传递
Cement Grinding System Status of Roller Press
2
作者 胡伟 王庆波 +2 位作者 李兵 丛茜 曲波 《Agricultural Science & Technology》 CAS 2012年第6期1328-1330,共3页
The working principle of cement roller press and current development of wear resistance on the cement grinding system status at home and abroad was described. The main improvement of previous research on the wear resi... The working principle of cement roller press and current development of wear resistance on the cement grinding system status at home and abroad was described. The main improvement of previous research on the wear resistance of roller press was proposed from three aspects of wear-resistant material, roller press roller structure, and surface morphology. 展开更多
关键词 Cement grinding system Grinding roller Bionic non-smooth Wear resistance
下载PDF
Simulation of clinker grinding circuits of cement plant based on process models calibrated using GA search method 被引量:3
3
作者 A.Farzanegan E.Ghasemi Ardi +1 位作者 A.Valian V.Hasanzadeh 《Journal of Central South University》 SCIE EI CAS 2014年第2期799-810,共12页
Particle size distributions of obtained samples from several sampling campaigns were determined and raw data were mass balanced before being used in simulation studies.After determination of breakage function,selectio... Particle size distributions of obtained samples from several sampling campaigns were determined and raw data were mass balanced before being used in simulation studies.After determination of breakage function,selection function,Bond work index,residence time distribution parameters,and Whiten's model parameters for air separators and diaphragms between the two compartments of tube ball mills,performance of the circuits was simulated for given throughputs and feed particle size distribution.Whiten's model parameters were determined by GA(genetic algorithm) toolbox of MATLAB software.Based on implemented models for modeling and simulation,optimization of circuits was carried out.It increased nearly 10.5% and 15.8% in fresh feed capacity input to each tube ball mill.In addition,circulating load ratios of circuits are modified to 118% and 127% from low level of 57% and 22%,respectively,and also cut points of air separators are adjusted at 30 and 40 μm from high range of 53 and 97 μm,respectively.All applications helped in well-operation and energy consumption reduction of equipments. 展开更多
关键词 cement plant clinker grinding genetic algorithm SIMULATION OPTIMIZATION
下载PDF
Grinding Properties of Abandoned Concrete
4
作者 ZHENG Fang-yu WANG Li-jiu LI Qiang 《Journal of China University of Mining and Technology》 EI 2007年第2期281-285,共5页
The grinding properties of abandoned concrete, which consists primarily of hardened cement, limestone aggregate and river sand, are studied. Theoretical models of grinding are used to explain the experimental observat... The grinding properties of abandoned concrete, which consists primarily of hardened cement, limestone aggregate and river sand, are studied. Theoretical models of grinding are used to explain the experimental observation. The results show that 1) The principle disintegration mechanism of hardened cement and river sand is volumetric grinding, although at later stages grinding of cement becomes difficult because of its flaked structure; 2) The lime- stone grinding process can be divided into two steps. First, volumetric grinding, with an obvious component of surface grinding, followed by primarily surface grinding as the micro-particle content increases; 3) Initially, the principle mechanism of grinding limestone and river sand is volumetric grinding, albeit less efficient grinding than if these components were ground separately, and; 4) After 10 to 20 min of grinding the grinding bottleneck phenomenon ap- pears and after 20 min of grinding the content of micro-particles is large and surface grinding is the main mechanism while the particle size of the mixture is smaller than that of separately ground river sand and cement but bigger than that of separately ground limestone. 展开更多
关键词 abandoned concrete cement stone LIMESTONE river sand GRINDING
下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部