处治红黏土水-力性能的团粒尺寸效应

红黏土因高黏粒含量和高含水率而易于成团,当掺入石灰或水泥处治时,会存在拌和不均的难题,进而影响处治效果。选择4组红黏土,其最大团粒尺寸D为5.0,2.0,1.0,0.5 mm。按照干质量比,偏高岭土∶石灰∶红黏土=5∶5∶90配置试样。然后,喷入蒸馏水增湿到含水率33.2%;最后,压实成型养护至预定龄期,再开展水-力性能和微观特性等试验。结果表明,随着最大团粒尺寸变大,处治红黏土线收缩率增大、无侧限抗压强度降低;但掺入偏高岭土后,相同团粒尺寸的处治土收缩性得到抑制,强度也得到提升。究其原因,红黏土团粒尺寸大,石灰只能附着在团粒的表面,仅形成团粒间的"桥接",不能形成包络状胶结;偏高岭土含有大量无定形的硅、铝氧化物,具有高"火山灰"活性,可以快速捕捉水化石灰中的钙离子,形成硅、铝酸钙等胶结物;同时,偏高岭土还充填了团粒间孔隙,二者的联合作用增强了处治红黏土的水-力性能。

Characteristic and optimization of ferrite-rich sulfoaluminate-based composite cement suitable for cold region tunnels

To develop suitable grouting materials for water conveyance tunnels in cold regions,firstly,this study investigated the performance evolution of ferrite-rich sulfoaluminate-based composite cement(FSAC grouting material)at 20 and 3℃.The results show that low temperature only delays the strength development of FSAC grouting material within the first 3 d.Then,the effect of four typical early strength synergists on the early properties of FSAC grouting material was evaluated to optimize the early(£1 d)strength at 3℃.The most effective synergist,Ca(HCOO)_(2),which enhances the low-temperature early strength without compromising fluidity was selected based on strength and fluidity tests.Its micro-mechanism was analyzed by XRD,TG,and SEM methods.The results reveal that the most suitable dosage range is 0.3 wt%−0.5 wt%.Proper addition of Ca(HCOO)_(2)changed the crystal morphology of the hydration products,decreased the pore size and formed more compact hydration products by interlocking and overlapping.However,excessive addition of Ca(HCOO)_(2)inhibited the hydration reaction,resulting in a simple and loose structure of the hydration products.The research results have reference value for controlling surrounding rock deformation and preventing water and mud inrushes during the excavation in cold region tunnels.

Effects of different modifiers on the properties of wood-polymer composites

Wood-polymer composites (WPC) were prepared from wood fiber and four kinds of plastics such as PE, PS, ABS, and SAN. The effects of different modifiers on the mechanical properties of the composites were studied. The results showed modifiers could raise the bonding strength of wood fiber with polymer and improve the mechanical properties of the composites. Different modifiers had different effects on the properties of wood-polymer composites, and comparatively the modifier of isocyanate produced a better result. Wood-polymer composite takes not only the advantages of both wood fiber and polymer, but waterproof, dimensional stability and dynamic strength are also significantly improved. Key word Wood fiber - Thermoplastic polyester - Wood-polymer composites - Modifier - Mechanical properties CLC number TB332 Document code A Foundation item: This study was supported by the Harbin Technology Tackle Key Plan (Development Research of Wood-Polymer Composites with High Wood Matrix) and by Heilongjing Nature Science Fund (Composite Mechanism Study of the Wood Polymer).Biography: XU Min (1963-), Female, Associate professor in Material Science and Engineering College, Northeast Forestry University, Harbin 150040, P. R. China.Responsible editor: Chai Ruihai

橡胶基体对橡胶/细菌纤维素晶须复合膜性能的影响

采用硫酸水解法制备细菌纤维素晶须(BCWs),并分别以丁苯橡胶(SBR)、天然橡胶(NR)和羧基丁腈橡胶(XNBR)作为基体,用蒸发法制备了橡胶/BCWs复合膜,研究了橡胶基体对复合膜的水溶胀、水刺激-力响应及降解性能的影响。结果表明,SBR/BCWs复合膜的平衡溶胀率高达72%,远高于NR/BCWs和XNBR/BCWs复合膜。3种复合膜表现出强烈的水刺激-力响应性能,其中SBR/BCWs复合膜综合性能最佳,NR/BCWs复合膜的重复使用性较好。BCWs的加入促进了3种复合膜的降解,其中SBR/BCWs复合膜的质量损失率最大。

Effects of superabsorbent polymer particles on flexural properties and self-healing behavior of ECC

In order to improve the self-healing behavior and the recovery of mechanical properties of engineered cementitious composites(ECC),the approach of incorporating superabsorbent polymer(SAP)in mixtures is investigated.The rapid water penetration test and four-point bending test were conducted to evaluate the effects of self-healing on the water permeability and mechanical properties of pre-damaged ECC.The self-healing process and self-healing products were observed by the environment scanning electron microscope(ESEM)and energy dispersive X-ray spectroscopy(EDS).The experimental results show that all ECC mixtures exhibit excellent flexural capacity,meanwhile maintaining a crack width below 50μm.The incorporation of SAP particles in ECC can apparently improve the mechanical recovery of ECC mixtures after 10 healing curing cycles,such as flexural deformation and flexural stiffness.The flexural stiffness of ECC containing 4%SAP particles after self-healing can be recovered to 80%.The self-healing test results show that when the water permeability of ECC mixtures incorporating SAP particles is close to zero,only three healing cycles are needed.When ECC incorpora ting more SAP particles,the accelerated self-healing process can be finished in the first three cycles,and self-healing product is mixed Ca(OH)2/CaCO 3 with CaCO 3 being a major component in the later stage.It is,therefore,feasible to produce ECC materials incorporating SAP particles,while simultaneously maintaining higher material ductility and self-healing behavior.

Influence of fins on tractor-type podded propulsor performance

A mathematical model of podded propulsors was established in order to investigate the influence of fins. The hydrodynamic performance of podded propulsors with and without fins was calculated, with interactions between propellers and pods and fins derived by iterative calculation. The differential equation based on velocity potential was adopted and hyperboloidal panels were used to avoid gaps between surface panels. The Newton-Raphson iterative procedure was used on the trailing edge to meet the pressure Kutta condition. The velocity distribution was calculated with the Yanagizawa method to eliminate the singularity caused by use of the numerical differential. Comparisons of the performance of podded propulsors with different fins showed that the thrust of propeller in a podded propulsor with fins is greater. The resistance of the pod is also reduced because of the thrust of the fin. The hydrodynamic performance of a podded propulsor with two fins is found to be best, the performance of a podded propulsor with one fin is not as good as two fins, and the performance of the common type is the worst.

Rules for confidence intervals of permeability coefficients for water flow in over-broken rock mass

Based on the steady-state seepage method, we used the Mechanical Testing and Simulation 815.02 System and a self-designed seepage instrument for over-broken stone to measure seepage properties of water flows in three types of crushed rock samples. Three methods of confidence interval in describing permeability coefficients are presented: the secure interval, the calculated interval and the systemic interval. The lower bound of the secure interval can be applied to water-inrush and the upper bound can solve the problem of connectivity. For the calculated interval, as the axial pressure increases, the length of confidence interval is shortened and the upper and lower bounds are reduced. For the systemic interval, the length of its confidence interval, as well as the upper and lower bounds, clearly vary under low axial pressure but are fairly similar under high axial pressure. These three methods provide useful information and references for analyzing the permeability coefficient of over-broken rock.

Evaluation of Station Keeping Systems for Deepwater Drilling Semi-submersibles

This paper addresses the need for systematic evaluation of the station keeping systems of deepwater drilling semi-submersibles.Based on the selected drilling semi-submersible configuration, the mooring systems were analyzed and designed for a range of water depths using different mooring line materials.These were steel wire rope, polyester rope and HMPE (high modulus poly ethylene).The mooring analysis was carried out using the advanced fully coupled time domain analysis method in the computer software package HARP.Diffraction analysis was first applied to solve the hydrodynamic properties of the vessel and then the motion equations of the complete dynamic system including the drilling rig, the mooring lines and risers were developed and solved in the time domain.Applying the advanced analysis method, a matrix of mooring systems was developed for operating in water depths of 1000 m, 1500 m, and 2 000 m using various mooring materials.The development of mooring systems was conducted in accordance with the commonly adopted mooring design code, API RP 2SK and API RP 2SM.Fresh attempts were then made to comparatively evaluate the mooring system's characteristics and global performance.Useful results have been obtained in terms of mooring materials, water depths, and key parameters of mooring configurations.The results provide in-depth insight for the design and operation of deepwater mooring systems in the South China Sea environment.

Hydrodynamic Performance of Flapping-foil Propulsion in the Influence of Vortices

Fish are able to make good use of vortices.In a complex flow field,many fish continue to maintain both efficient cruising and maneuverability.Traditional man-made propulsion systems perform poorly in complex flow fields.With fish-like propulsion systems,it is important to pay more attention to complex flow fields.In this paper,the influence of vortices on the hydrodynamic performance of 2-D flapping-foils was investigated.The flapping-foil heaved and pitched under the influence of inflow vortices generated by an oscillating D-section cylinder.A numerical simulation was run based the finite volume method,using the computational fluid dynamics(CFD) software FLUENT with Reynolds-averaged Navier-Stokes(RANS) equations applied.In addition,dynamic mesh technology and post processing systems were also fully used.The calculations showed four modes of interaction.The hydrodynamic performance of flapping-foils was analyzed and the results compared with experimental data.This validated the numerical simulation,confirming that flapping-foils can increase efficiency by absorbing energy from inflow vortices.

Resistance and Seakeeping Numerical Performance Analyses of a Semi-Small Waterplane Area Twin Hull at Medium to High Speeds

The hydrodynamic analysis of a new semi-small waterplane area twin hull （SWATH） suitable for various applications such as small and medium size passenger ferries is presented. This may be an attractive crossover configuration resulting from the merging of two classical shapes： a conventional SWATH and a fast catamaran. The final hull design exhibits a wedge-like waterline shape with the maximum beam at the stem; the hull ends with a very narrow entrance angle, has a prominent bulbous bow typical of SWATH vessels, and features full stern to arrange waterjet propellers. Our analysis aims to perform a preliminary assessment of the hydrodynamic performance of a hull with such a complex shape both in terms of resistance of the hull in calm water and seakeeping capability in regular head waves and compare the performance with that of a conventional SWATH. The analysis is performed using a boundary element method that was preliminarily validated on a conventional SWATH vessel.

Hydrodynamic Performance of Multiple-Row Slotted Breakwaters

This study examines the hydrodynamic performance of multiple-row vertical slotted breakwaters. We developed a mathematical model based on an eigenfunction expansion method and a least squares technique for Stokes second-order waves. The numerical results obtained for limiting cases of double-row and triple-row walls are in good agreement with results of previous studies and experimental results. Comparisons with experimental measurements of the reflection, transmission, and dissipation coefficients （CR, Cr, and CE） for double-row walls show that the proposed mathematical model adequately reproduces most of the important features. We found that for double-row walls, the CR increases with increasing wave number, kd, and with a decreasing permeable wall part, din. The Cr follows the opposite trend. The CE slowly increases with an increasing kd for lower kd values, reaches a maximum, and then decreases again. In addition, an increasing porosity of dm would significantly decrease the CR while increasing the Cr. At lower values of kd, a decreasing porosity increases the CE, but for high values of kd, a decreasing porosity reduces the Ce. The numerical results indicate that, for triple-row walls, the effect of the arrangement of the chamber widths on hydrodynamic characteristics is not significant, except when kd〈0.5 Double-row slotted breakwaters may exhibit a good wave-absorbing performance at kd〉0.5, where by the horizontal wave force may be smaller than that of a single wall. On the other hand, the difference between double-row and triple-row vertical slotted breakwaters is marginal.

A CFD Based Investigation of the Unsteady Hydrodynamic Coefficients of 3-D Fins in Viscous Flow

The motion of the fins and control surfaces of underwater vehicles in a fluid is an interesting and challenging research subject.Typically the effect of fin oscillations on the fluid flow around such a body is highly unsteady, generating vortices and requiring detailed analysis of fluid-structure interactions.An understanding of the complexities of such flows is of interest to engineers developing vehicles capable of high dynamic performance in their propulsion and maneuvering.In the present study, a CFD based RANS simulation of a 3-D fin body moving in a viscous fluid was developed.It investigated hydrodynamic performance by evaluating the hydrodynamic coefficients (lift, drag and moment) at two different oscillating frequencies.A parametric analysis of the factors that affect the hydrodynamic performance of the fin body was done, along with a comparison of results from experiments.The results of the simulation were found in close agreement with experimental results and this validated the simulation as an effective tool for evaluation of the unsteady hydrodynamic coefficients of 3-D fins.This work can be further be used for analysis of the stability and maneuverability of fin actuated underwater vehicles.

Simultaneous Effects of Hydrostatic Pressure and Conduction Band Non-parabolicity on Binding Energies and Diamagnetic Susceptibility of a Hydrogenic Impurity in Spherical Quantum Dots

Simultaneous effects of conduction band non-parabolicity and hydrostatic pressure on the binding energies of 1S, 2S, and 2P states along with diamagnetic susceptibility of an on-center hydrogenic impurity confined in typical GaAs/Alx- Ga1-x As spherical quantum dots are theoretically investigated using the matrix diagonalization method. In this regard, the effect of band non-parabolieity has been performed using the Luttinger-Kohn effective mass equation. The binding energies and the diamagnetic susceptibility of the hydrogenic impurity are computed as a function of the dot radius and different values of the pressure in the presence of conduction band non-parabolicity effect. The results we arrived at are as follows： the incorporation of the band edge non-parabolicity increases the binding energies and decreases the absolute value of the diamagnetic susceptibility for a given pressure and radius; the binding energies increase and the magnitude of the diamagnetic susceptibility reduces with increasing pressure.

The step-by-step CFD design method of pressure-compensating emitter

In order to improve the design and research and development (R & D) efficiency of the pressure- compensating drip irrigation emitter,a step-by-step computational fluid dynamics (CFD) design method was proposed based on CFD theory combined with the finite element method. By analyzing its hydraulic performance through the step-by-step CFD method,the prediction pressure-flow curve(p-Q curve) of the pressure-compensating emitter was obtained. Then the test samples were fabricated using rapid prototype and manufacturing(RP & M) technology. The emitters' hydraulic performance experiment was carried out and the experimental p-Q curve was obtained. The step-by-step CFD design method was verified by comparing the experimental p-Q curve with the prediction values,which showed that the prediction values met the experimental results well within the normal range of the emitter's working pressure. On this basis,the effect of the emitter structure on its pressure-compensating performance was studied,which showed that the height of the pressure-compensating region had significant effects on the emitter's pressure-compensating performance. Series products of the pressure-compensating emitter could be designed by changing the region's height.

Mechanical and electrochemical characteristics in sea water of 5052-O aluminum alloy for ship

The optimum corrosion protection potentials were examined for 5052-O Al alloy,which is mainly used in ships.Various electrochemical experiments were carried out and the surface morphologies of specimens were observed by scanning electron microscopy（SEM） in order to determine the optimum corrosion protection potential to overcome pitting,corrosion,stress corrosion cracking（SCC）,and hydrogen embrittlement in sea water.An optimum protection potential range of-1.3 V to-0.7 V was determined under the application of an impressed current cathodic protection（ICCP） system.The low current densities were shown in the range of-1.3 V to-0.7 V in the electrochemical experiments and good specimen surface morphologies were observed after potentiostatic experiment.

Effect of heating-rate on failure temperature of pre-loaded magnesium alloy

The response and failure of magnesium alloy AZ31 specimens subjected to different pre-loaded-stress levels and heating rates were investigated with a Gleeble-1500 thermo-mechanical material testing system.It is found that the increases of either pre-loaded stresses or heating-rates decrease the failure temperatures of the specimens.The metallographs of the tested specimens were also observed.It is shown that the high heating-rate may cause stronger local thermal inconsistency,which remarkably increases the microdefects and reduces the macroscopic mechanical properties of the material.

Self-renewal Capacity of Several Species of the Genus Sternbergia Possessing Medicinal Properties

The present work dealt with sexual reproduction capacity of three relic species of the genus Sternbergia （family AmaryUidaceae） distributed in the Caucasus, i.e., Sternbergia lutea （L.） Ker Gawl. ex Spreng., Sternbergiafischeriana （Herb.） Roem and Sternbergia colchiciflora Waldst. ＆ Kit.. Under this study, the natural populations of species, which possess valuable medicinal and ornamental properties, have been assessed by experts as vulnerable, and S. colchiciflora is included in the red list of endemic plants of the Caucasus, as having status of the critically endangered species. The situation is aggravated by the poor self-regeneration capacity of these species, which is one of the main factors responsible for the sustainability of the population of this or that species in the wild. Self-regeneration capacity for sexual reproduction was investigated in the listed species of the genus Sternbergia using common methods of embryology and reproduction biology. In conditions of the National Botanical Garden of Georgia （NBGG）, the species S. lutea and S. fischeriana prove to be completely infertile and propagate vegetatively by bulblets, while S. colchiciflora revealed the ability for propagation by seed. Long-term conservation of seeds of the studied species S. colchiciflora in the Caucasus Regional Seed Bank （CRSB） and establishing of living collections of this species at the experimental plot were chosen as the method for safeguarding this critically endangered species.

Performance of water-based foams affected by chemical inhibitors to retard spontaneous combustion of coal

The micelle generating process of the sodium dodecyl sulfate(SDS) solution with the addition of chemical inhibitors was elucidated using phase separation model, and the descending order of the capacity for the selected chemical inhibitors to reduce the critical micelle concentrations of the solution are Mg Cl_2, Ca Cl_2,NH_4HCO_3 and NH_4Cl. The data to quantitatively describe the foam decay process, including foaming ratio,foam life and decay behaviors, was obtained by pressure measuring system. The results indicate that chemical inhibitors can improve the solution foamability. The capacity of the inhibitors to enhance the solution foamability is sorted as NH_4 Cl, NH_4HCO_3, Mg Cl2 and Ca Cl_2 which can distinctly improve the foam stability as well. The capacity of the inhibitors to enhance the SDS foam stability can be arranged as Mg Cl_2, NH_4 Cl, NH_4HCO_3 and Ca Cl_2. It is observed that the gravity drainage plays a leading role in the increase of proportion of diffusion drainage. The oxidation dynamic parameters of the coal samples treated by inhibition foams were investigated using thermal analysis technique, and their synergistic effects on inhibiting coal oxidation were explored.

Enhancing the Mechanical Properties of Gap Graded Cold Asphalt Containing Cement Utilising By-Product Material

The little stiffness modulus, high voidage and long curing time has limited the use of CBEM＇s （cold bituminous emulsion mixtures） in road and highways to pavement experiencing low traffic. The aim of this study is to improve the properties of gap graded CRA （cold rolled asphal0 containing OPC （ordinary portland cement） as filler by addition of a by-product material as an activator. OPC was added to the CRA as a replacement to the conventional mineral filler （0%-100%）, while LJMUA （Liverpool John Moores University Activator） was added as an additive in the range from 0%-3% by total mass of aggregate. Laboratory tests included stiffness modulus and uniaxial creep test to assess the mechanical properties. The results have shown a considerable improvement in the mechanical properties from the addition of LJMUA to the CRA containing OPC especially for the early life stiffness modulus that is the main disadvantage of the cold mixtures.

Three Dimensional Numerical Simulation of Convection-Condensation of Vapor with High Concentration Air in Tube with Inserts

A three-dimensional numerical model is presented for studying the convection-condensation of mixture with vapor in a tube with edgefold-twisted-tape inserts under transition flow.According to the diffusion layer theory and laminar species transport,a condensation model with user defined function is proposed and compared with heat and mass transfer analogy and experimental test.With the condensation model,the influences of gap width and op-erating parameters on thermal-hydrodynamics performance are simulated.As the gap width increases,convection and condensation heat transfer increase initially and then decrease,while convection heat transfer increases sharply and then decreases slightly.Increasing vapor fraction has a significant effect on condensation heat transfer but it has little effect on convective heat transfer.With the increase of inner wall temperature both convection and condensa-tion heat transfer all decrease and the ratio of condensation to total heat decrease dramatically.Increases inlet tem-perature mainly affects convection heat transfer.