期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
基于配流盘表面形貌的柱塞泵空化现象研究 被引量:2
1
作者 张娇 王兆强 +2 位作者 韩博 孙令涛 高伟 《机电工程》 CAS 北大核心 2022年第10期1398-1404,共7页
针对轴向柱塞泵配流副内的空化现象,建立了考虑配流盘表面形貌的柱塞泵配流副空化模型,分析了压力、转速和配流盘表面形貌对轴向柱塞泵配流副内空化现象的影响。首先,由于机加工零部件表面具备分形特征,采用了分形理论模拟配流盘表面形... 针对轴向柱塞泵配流副内的空化现象,建立了考虑配流盘表面形貌的柱塞泵配流副空化模型,分析了压力、转速和配流盘表面形貌对轴向柱塞泵配流副内空化现象的影响。首先,由于机加工零部件表面具备分形特征,采用了分形理论模拟配流盘表面形貌,在此基础上建立了轴向柱塞泵配流副空化模型;然后,采用有限差分法和松弛迭代法求解了数学模型,得到了符合精度要求的数值解,从而得出了配流副油膜压力分布特征,在此基础上分析了配流盘表面容易发生空化的位置;最后,通过改变配流副的压力、转速和分形参数,得到了不同的压力、缸体转速和表面形貌对配流副空化现象的影响。研究结果表明:配流盘表面易在高压和低压的过渡区域发生局部空化,当配流副排油腔压力达到30 MPa,且配流盘表面较粗糙时,配流盘局部气体体积分数达到92%左右;采用提高配流盘表面的加工精度,降低其表面粗糙度的方法,可以降低配流盘表面产生空化现象的严重程度。 展开更多
关键词 容积泵 配流副空化模型 表面粗糙度 排油腔压力 局部气体体积分数 缸体转速 空化程度 油膜润滑性能
下载PDF
Oil-Film Clutch in Soft-Start of Belt Conveyor 被引量:3
2
作者 周满山 魏宸官 +1 位作者 于岩 张媛 《Journal of Beijing Institute of Technology》 EI CAS 2002年第2期142-145,共4页
The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch... The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch, equations that are used to decide the lubricating oil flow and the number of oil films (i.e. the number of rotating and stationary plates) are deduced theoretically. Also key parameters are provided for the design of the hydraulic system. All these together provide the theoretical basis for the soft start design of the belt conveyor and references for the application of the oil film clutch in similar fields. 展开更多
关键词 belt conveyor soft start oil film clutch lubricating theory
下载PDF
Tribological and economic evaluation of recycled mineral lubricating oils 被引量:4
3
作者 LIU JianFang GU KaLi +2 位作者 DUAN HaiTao ZHAO Yuan LI Jian 《Science China(Technological Sciences)》 SCIE EI CAS 2013年第12期2964-2972,共9页
Seven kinds of used mineral lubricating oils,including hydraulic oils,film bearing oils,steam turbine oil and gear oils,were recycled by reclamation and adding additives.Physical and chemical properties of the recycle... Seven kinds of used mineral lubricating oils,including hydraulic oils,film bearing oils,steam turbine oil and gear oils,were recycled by reclamation and adding additives.Physical and chemical properties of the recycled oils were measured and their lubrication performances were evaluated by the original and modified four-ball testers.Worn surfaces were analyzed by energy dispersive X-ray spectroscopy and Raman microscope.The recycling costs of burning,re-refined and refortified were estimated.Results showed that physical and chemical properties of the refortified oils were improved effectively and became in the industrial access standard.With the different friction materials under different loads,refortified oils provided excellent lubrication performances,much better than those of fresh oils.Because of additives replenished,the different lubrication films could form on the worn surfaces.A rough financial calculation revealed that the refortification process could produce the most economic value among the three methods. 展开更多
关键词 lubricating oil refortification process lubrication performance economic evaluation physical and chemical property
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部