采用电晕注极和热注极技术,在厚度为25μm的氟化乙丙烯共聚物(FEP)表面制备了宽度为2 mm和3mm的具有栅型电场分布的驻极体,研究了注极温度和电极宽度对其电荷存储性能的影响.样品注极后经150天的存储,栅型电场分布变得清晰而有规律,覆...采用电晕注极和热注极技术,在厚度为25μm的氟化乙丙烯共聚物(FEP)表面制备了宽度为2 mm和3mm的具有栅型电场分布的驻极体,研究了注极温度和电极宽度对其电荷存储性能的影响.样品注极后经150天的存储,栅型电场分布变得清晰而有规律,覆盖铝电极区电位已衰减至接近零,未覆盖铝电极区仍保持高电位;对电极宽度为2 mm和3 mm的样品,覆盖铝电极区与未覆盖铝电极区的表面电位差分别为110 V和130V(电场强度差分别为44 k V/cm和52 k V/cm).表面电位跟踪测试结果表明:电晕注极样品初始表面电位高于热注极样品;在相同的注极方法下,注极温度越高初始表面电位越高,电极宽度越小初始表面电位越低.依据电晕注极和热注极原理对实验结果的分析表明,FEP和金属铝在电荷存储性能上的差异是FEP表面蒸镀铝电极后能获得栅型电场分布的原因所在.展开更多
Based on a short anode GTO structure (SA-GTO),a novel GTO structure called an injection efficiency controlled gate turn off thyristor (IEC-GTO) is proposed,in which the injection efficiency can be controlled via a...Based on a short anode GTO structure (SA-GTO),a novel GTO structure called an injection efficiency controlled gate turn off thyristor (IEC-GTO) is proposed,in which the injection efficiency can be controlled via an additional thin oxide layer located in the short anode contact region. The forward blocking, conducting, and switching characteristics are analyzed and compared with an SA-GTO and conventional GTO. The results show that the IEC-GTO can obtain a better trade-off relation between on-state and turn-off characteristics. Additionally,the width of the oxide layer covering the anode region and the doping concentration of the anode region are optimized, the process feasibility is analyzed, and a realization scheme is given. The results show that the introduction of an oxide layer would not increase the complexity of process of the IEC-GTO.展开更多
The methodology of predicting pile shaft skin ultimate friction has been studied in a systematic way. In the light of that, the analysis of the pile shaft resistance for bored and cast in situ piles in cohesive soil...The methodology of predicting pile shaft skin ultimate friction has been studied in a systematic way. In the light of that, the analysis of the pile shaft resistance for bored and cast in situ piles in cohesive soils was carried out thoroughly in the basis of field performance data of 10 fully instrumented large diameter bored piles (LDBPs) used as the bridge foundation. The undrained strength index μ in term of cohesive soils was brought forward in allusion to the cohesive soils in the consistence plastic state, and can effectively combine the friction angle and the cohesion of cohesive soils in undrained condition. And that the classical ' α method' was modified much in effect to predict the pile shaft skin friction of LDBPs in cohesive soils. Furthermore, the approach of standard penetration test (SPT) N value used to estimate the pile shaft skin ultimate friction was analyzed, and the calculating formulae were established for LDBPs in clay and silt clay respectively.展开更多
The channel lateral pocket or halo region of NMOSFET characterized by interface state R G current of a forward gated diode has been investigated numerically for the first time.The result of numerical analysis demons...The channel lateral pocket or halo region of NMOSFET characterized by interface state R G current of a forward gated diode has been investigated numerically for the first time.The result of numerical analysis demonstrates that the effective surface doping concentration and the interface state density of the pocket or halo region are interface states R G current peak position dependent and amplitude dependent,respectively.It can be expressed quantitatively according to the device physics knowledge,thus,the direct characterization of the interface state density and the effective surface doping concentration of the pocket or halo becomes very easy.展开更多
A novel Sb2O3/Sb2S3/FeOOH photoanode was fabricated via a simple solution impregnation method along with chemical bath deposition and post-sulfidation.The X-ray diffractometry,Raman measurement,and X-ray photoelectron...A novel Sb2O3/Sb2S3/FeOOH photoanode was fabricated via a simple solution impregnation method along with chemical bath deposition and post-sulfidation.The X-ray diffractometry,Raman measurement,and X-ray photoelectron spectroscopy show that the Sb2O3/Sb2S3/FeOOH thin films are successfully prepared.SEM−EDS analyses reveal that the surface of Sb2O3/Sb2S3 thin films becomes rough after the immersion in the FeCl3 solution.The optimized impregnation time is found to be 8 h.The FeOOH co-catalyst loaded Sb2O3/Sb2S3 electrode exhibits an enhanced photocurrent density of 0.45 mA/cm2 at 1.23 V versus RHE under simulated 1 sun,which is approximately 1.41 times compared to the photocurrent density of the unloaded one.Through the further tests of UV−Vis spectroscopy,the electrochemical impedance spectra,and the PEC measurements,the enhancement can result from the increased light-harvesting ability,the decreased interface transmission impedance,and the remarkably enhanced carrier injection efficiency.展开更多
With the aim of achieving high coupling power of RWG SLDs into SMFs,the structure dependences of the output power and the near field pattern are investigated. The thicknesses of the layers between the active region an...With the aim of achieving high coupling power of RWG SLDs into SMFs,the structure dependences of the output power and the near field pattern are investigated. The thicknesses of the layers between the active region and the ridge waveguide are optimized by taking into account the injected carrier distribution and local material gain in the SLD cross section.展开更多
The hole injection,the radiative recombination and the device luminescent efficiencies of amorphous silicon carbide thin film p-i-n junction light emitting diodes are quantitatively calculated,and the effect of the ca...The hole injection,the radiative recombination and the device luminescent efficiencies of amorphous silicon carbide thin film p-i-n junction light emitting diodes are quantitatively calculated,and the effect of the carrier(especially the hole) injection and recombination processes on the device luminescent characteristics are revealed.Without considering the device junction temperature,it is found that the device luminescent efficiency mainly depends on the hole injection efficiency at low field and the hole radiative recombination efficiency at high field respectively.The theoretical analyses are in well agreement with the experimental results.展开更多
Objective To propose a Light-Atten-Pose-based algorithm for classifying abnormal morphology in traditional Chinese medicine(TCM)inspection to solve the problem of relying on manual labor or expensive equipment with pe...Objective To propose a Light-Atten-Pose-based algorithm for classifying abnormal morphology in traditional Chinese medicine(TCM)inspection to solve the problem of relying on manual labor or expensive equipment with personal subjectivity or high cost.Methods First,this paper establishes a dataset of abnormal morphology for Chinese medicine diagnosis,with images from public resources and labeled with category labels by several Chinese medicine experts,including three categories:normal,shoulder abnormality,and leg abnormality.Second,the key points of human body are extracted by Light-Atten-Pose algo-rithm.Light-Atten-Pose algorithm uses lightweight EfficientNet network and polarized self-attention(PSA)mechanism on the basis of AlphaPose,which reduces the computation amount by using EfficientNet network,and the data is finely processed by using PSA mecha-nism in spatial and channel dimensions.Finally,according to the theory of TCM inspection,the abnormal morphology standard based on the joint angle difference is defined,and the classification of abnormal morphology of Chinese medical diagnosis is realized by calculat-ing the angle between key points.Accuracy,frames per second(FPS),model size,parameter set(Params),and giga floating-point operations per second(GFLOPs)are chosen as the eval-uation indexes for lightweighting.Results Validation of the Light-Atten-Pose algorithm on the dataset showed a classification accuracy of 96.23%,which is close to the original AlphaPose model.However,the FPS of the improved model reaches 41.6 fps from 16.5 fps,the model size is reduced from 155.11 MB to 33.67 MB,the Params decreases from 40.5 M to 8.6 M,and the GFLOPs reduces from 11.93 to 2.10.Conclusion The Light-Atten-Pose algorithm achieves lightweight while maintaining high ro-bustness,resulting in lower complexity and resource consumption and higher classification accuracy,and the experiments prove that the Light-Atten-Pose algorithm has a better overall performance and has practical application in the pose estimation task.展开更多
A 300 μm×300 μm light emitting diode(LED) chip is divided into nine 80 μm×80 μm units with 30 μm spacing between adjacent ones. After arraying, the total saturation light output power and the maximum in...A 300 μm×300 μm light emitting diode(LED) chip is divided into nine 80 μm×80 μm units with 30 μm spacing between adjacent ones. After arraying, the total saturation light output power and the maximum injection current are enhanced by 5.19 times and nearly 7 times, respectively. In addition, the test results demonstrate that the illuminance uniformity on the receiving surface reaches the optimum when the spacing between the arrays is equal to the maximum flat condition. The larger the number of arrays, the greater the area with uniform illuminance on the receiving surface.展开更多
An NH2+ ion implantation-modified indium tin oxide film was prepared and the implantation of amino groups on the indium tin oxide substrate was verified by X-ray photoelectron spectroscopy analysis.The gold nanopartic...An NH2+ ion implantation-modified indium tin oxide film was prepared and the implantation of amino groups on the indium tin oxide substrate was verified by X-ray photoelectron spectroscopy analysis.The gold nanoparticles attached surface could be obtained by self-assembly of different sized colloidal gold nanoparticles onto the NH2+ ion implantation-modified indium tin oxide surface.By scanning electron microscopy and electrochemical techniques,the as-prepared AuNPs attached NH2+ ion implantation-modified indium tin oxide electrode was characterized and compared with bare indium tin oxide electrode.Using a [Fe(CN)6]3 /[Fe(CN)6]4 redox probe,the increasingly facile heterogeneous electron transfer kinetics resulting from the attached gold nanoparticle arrays was observed.The gold nanoparticle arrays exhibited high catalytic activity toward the electro-oxidation of nitric oxide,which could provide electroanalytical application for nitric oxide sensing.展开更多
A novel crosslinkable water/alcohol soluble conjugated polymer PFN-C containing oxetane groups and aminoalkyl groups in the side chains has been developed and used as highly efficient electron injection and transporti...A novel crosslinkable water/alcohol soluble conjugated polymer PFN-C containing oxetane groups and aminoalkyl groups in the side chains has been developed and used as highly efficient electron injection and transporting material for polymer light-emitting diodes (PLEDs). The unique solubility in polar solvents and crosslinkable ability of PFN-C render it a good can- didate for solution processed multilayer PLEDs. It was found that PFN-C can greatly enhance the electron injection from high work-function metal cathode, due to its pendant amino groups. As a result, PLEDs with PFN-C/Al cathode exhibited compara- ble device performance to the devices with Ba/Al cathode. The resulting green light-emitting device showed promising perfor- mance with a maximum luminance efficiency of 13.53 cd A-1.展开更多
A double T-shaped device model is constructed to investigate the spin polarized current injection and transportation properties in organic semiconductors.Based on the spin diffusion theory and Ohm’s law and consideri...A double T-shaped device model is constructed to investigate the spin polarized current injection and transportation properties in organic semiconductors.Based on the spin diffusion theory and Ohm’s law and considering the different charge-spin relationship of the special carriers in organic semiconductors,the current spin polarization has been obtained.Effects of the branch current ratio and the polaron proportion on the spin polarized current injection efficiency are studied.From the calculation,it is found that the improvement of the spin polarized current injection efficiency can be obtained by adjusting the branch current ratio;moreover,high polaron proportion in organic semiconductors is beneficial for obtaining high current spin polarization.展开更多
Utilization of visible light is of crucial importance for exploiting efficient semiconductor catalysts for solar water splitting. In this study, an advanced ion implantation method was utilized to dope Cu ions into Zn...Utilization of visible light is of crucial importance for exploiting efficient semiconductor catalysts for solar water splitting. In this study, an advanced ion implantation method was utilized to dope Cu ions into ZnO nanorod arrays for photoelectrochemical water splitting in visible light. X-ray diffraction (XRD) and X-ray photo-electron spectroscopy (XPS) results revealed that Cu^+ together with a small amount of Cu^2+ were highly dispersed within the ZnO nanorod arrays. The Cu ion doped ZnO nanorod arrays displayed extended optical absorption and enhanced photoelectrochemical performance under visible light illumination (A 〉 420 nm). A considerable photocurrent density of 18 μA/cm^2 at 0.8 V (vs. a saturated calomel electrode) was achieved, which was about 11 times higher than that of undoped ZnO nanorod arrays. This study proposes that ion implantation could be an effective approach for developing novel visible-light-driven photocatalytic materials for water splitting.展开更多
文摘采用电晕注极和热注极技术,在厚度为25μm的氟化乙丙烯共聚物(FEP)表面制备了宽度为2 mm和3mm的具有栅型电场分布的驻极体,研究了注极温度和电极宽度对其电荷存储性能的影响.样品注极后经150天的存储,栅型电场分布变得清晰而有规律,覆盖铝电极区电位已衰减至接近零,未覆盖铝电极区仍保持高电位;对电极宽度为2 mm和3 mm的样品,覆盖铝电极区与未覆盖铝电极区的表面电位差分别为110 V和130V(电场强度差分别为44 k V/cm和52 k V/cm).表面电位跟踪测试结果表明:电晕注极样品初始表面电位高于热注极样品;在相同的注极方法下,注极温度越高初始表面电位越高,电极宽度越小初始表面电位越低.依据电晕注极和热注极原理对实验结果的分析表明,FEP和金属铝在电荷存储性能上的差异是FEP表面蒸镀铝电极后能获得栅型电场分布的原因所在.
文摘Based on a short anode GTO structure (SA-GTO),a novel GTO structure called an injection efficiency controlled gate turn off thyristor (IEC-GTO) is proposed,in which the injection efficiency can be controlled via an additional thin oxide layer located in the short anode contact region. The forward blocking, conducting, and switching characteristics are analyzed and compared with an SA-GTO and conventional GTO. The results show that the IEC-GTO can obtain a better trade-off relation between on-state and turn-off characteristics. Additionally,the width of the oxide layer covering the anode region and the doping concentration of the anode region are optimized, the process feasibility is analyzed, and a realization scheme is given. The results show that the introduction of an oxide layer would not increase the complexity of process of the IEC-GTO.
文摘The methodology of predicting pile shaft skin ultimate friction has been studied in a systematic way. In the light of that, the analysis of the pile shaft resistance for bored and cast in situ piles in cohesive soils was carried out thoroughly in the basis of field performance data of 10 fully instrumented large diameter bored piles (LDBPs) used as the bridge foundation. The undrained strength index μ in term of cohesive soils was brought forward in allusion to the cohesive soils in the consistence plastic state, and can effectively combine the friction angle and the cohesion of cohesive soils in undrained condition. And that the classical ' α method' was modified much in effect to predict the pile shaft skin friction of LDBPs in cohesive soils. Furthermore, the approach of standard penetration test (SPT) N value used to estimate the pile shaft skin ultimate friction was analyzed, and the calculating formulae were established for LDBPs in clay and silt clay respectively.
文摘The channel lateral pocket or halo region of NMOSFET characterized by interface state R G current of a forward gated diode has been investigated numerically for the first time.The result of numerical analysis demonstrates that the effective surface doping concentration and the interface state density of the pocket or halo region are interface states R G current peak position dependent and amplitude dependent,respectively.It can be expressed quantitatively according to the device physics knowledge,thus,the direct characterization of the interface state density and the effective surface doping concentration of the pocket or halo becomes very easy.
基金Project(51674298)supported by the National Natural Science Foundation of ChinaProject(2017JJ3384)supported by the Natural Science Foundation of Hunan Province,ChinaProject(2018M630910)supported by the China Postdoctoral Science Foundation。
文摘A novel Sb2O3/Sb2S3/FeOOH photoanode was fabricated via a simple solution impregnation method along with chemical bath deposition and post-sulfidation.The X-ray diffractometry,Raman measurement,and X-ray photoelectron spectroscopy show that the Sb2O3/Sb2S3/FeOOH thin films are successfully prepared.SEM−EDS analyses reveal that the surface of Sb2O3/Sb2S3 thin films becomes rough after the immersion in the FeCl3 solution.The optimized impregnation time is found to be 8 h.The FeOOH co-catalyst loaded Sb2O3/Sb2S3 electrode exhibits an enhanced photocurrent density of 0.45 mA/cm2 at 1.23 V versus RHE under simulated 1 sun,which is approximately 1.41 times compared to the photocurrent density of the unloaded one.Through the further tests of UV−Vis spectroscopy,the electrochemical impedance spectra,and the PEC measurements,the enhancement can result from the increased light-harvesting ability,the decreased interface transmission impedance,and the remarkably enhanced carrier injection efficiency.
文摘With the aim of achieving high coupling power of RWG SLDs into SMFs,the structure dependences of the output power and the near field pattern are investigated. The thicknesses of the layers between the active region and the ridge waveguide are optimized by taking into account the injected carrier distribution and local material gain in the SLD cross section.
文摘The hole injection,the radiative recombination and the device luminescent efficiencies of amorphous silicon carbide thin film p-i-n junction light emitting diodes are quantitatively calculated,and the effect of the carrier(especially the hole) injection and recombination processes on the device luminescent characteristics are revealed.Without considering the device junction temperature,it is found that the device luminescent efficiency mainly depends on the hole injection efficiency at low field and the hole radiative recombination efficiency at high field respectively.The theoretical analyses are in well agreement with the experimental results.
基金National Key Research and Development Program of China(2022YFC3502302)。
文摘Objective To propose a Light-Atten-Pose-based algorithm for classifying abnormal morphology in traditional Chinese medicine(TCM)inspection to solve the problem of relying on manual labor or expensive equipment with personal subjectivity or high cost.Methods First,this paper establishes a dataset of abnormal morphology for Chinese medicine diagnosis,with images from public resources and labeled with category labels by several Chinese medicine experts,including three categories:normal,shoulder abnormality,and leg abnormality.Second,the key points of human body are extracted by Light-Atten-Pose algo-rithm.Light-Atten-Pose algorithm uses lightweight EfficientNet network and polarized self-attention(PSA)mechanism on the basis of AlphaPose,which reduces the computation amount by using EfficientNet network,and the data is finely processed by using PSA mecha-nism in spatial and channel dimensions.Finally,according to the theory of TCM inspection,the abnormal morphology standard based on the joint angle difference is defined,and the classification of abnormal morphology of Chinese medical diagnosis is realized by calculat-ing the angle between key points.Accuracy,frames per second(FPS),model size,parameter set(Params),and giga floating-point operations per second(GFLOPs)are chosen as the eval-uation indexes for lightweighting.Results Validation of the Light-Atten-Pose algorithm on the dataset showed a classification accuracy of 96.23%,which is close to the original AlphaPose model.However,the FPS of the improved model reaches 41.6 fps from 16.5 fps,the model size is reduced from 155.11 MB to 33.67 MB,the Params decreases from 40.5 M to 8.6 M,and the GFLOPs reduces from 11.93 to 2.10.Conclusion The Light-Atten-Pose algorithm achieves lightweight while maintaining high ro-bustness,resulting in lower complexity and resource consumption and higher classification accuracy,and the experiments prove that the Light-Atten-Pose algorithm has a better overall performance and has practical application in the pose estimation task.
基金supported by the Young Scientists Fund of the National Natural Science Foundation of China(No.61204055)
文摘A 300 μm×300 μm light emitting diode(LED) chip is divided into nine 80 μm×80 μm units with 30 μm spacing between adjacent ones. After arraying, the total saturation light output power and the maximum injection current are enhanced by 5.19 times and nearly 7 times, respectively. In addition, the test results demonstrate that the illuminance uniformity on the receiving surface reaches the optimum when the spacing between the arrays is equal to the maximum flat condition. The larger the number of arrays, the greater the area with uniform illuminance on the receiving surface.
基金supported by the National Nature Science Foundation of China (20211130505)the Fundamental Research Funds for the Central Universities of China
文摘An NH2+ ion implantation-modified indium tin oxide film was prepared and the implantation of amino groups on the indium tin oxide substrate was verified by X-ray photoelectron spectroscopy analysis.The gold nanoparticles attached surface could be obtained by self-assembly of different sized colloidal gold nanoparticles onto the NH2+ ion implantation-modified indium tin oxide surface.By scanning electron microscopy and electrochemical techniques,the as-prepared AuNPs attached NH2+ ion implantation-modified indium tin oxide electrode was characterized and compared with bare indium tin oxide electrode.Using a [Fe(CN)6]3 /[Fe(CN)6]4 redox probe,the increasingly facile heterogeneous electron transfer kinetics resulting from the attached gold nanoparticle arrays was observed.The gold nanoparticle arrays exhibited high catalytic activity toward the electro-oxidation of nitric oxide,which could provide electroanalytical application for nitric oxide sensing.
基金financially supported by the Natural Science Foundation of China (50990065, 51010003, 51073058 & 20904011)the National Basic Research Program of China (973 Program, 2009CB623601)the Fun-damental Research Funds for the Central Universities, South China Uni-versity of Technology
文摘A novel crosslinkable water/alcohol soluble conjugated polymer PFN-C containing oxetane groups and aminoalkyl groups in the side chains has been developed and used as highly efficient electron injection and transporting material for polymer light-emitting diodes (PLEDs). The unique solubility in polar solvents and crosslinkable ability of PFN-C render it a good can- didate for solution processed multilayer PLEDs. It was found that PFN-C can greatly enhance the electron injection from high work-function metal cathode, due to its pendant amino groups. As a result, PLEDs with PFN-C/Al cathode exhibited compara- ble device performance to the devices with Ba/Al cathode. The resulting green light-emitting device showed promising perfor- mance with a maximum luminance efficiency of 13.53 cd A-1.
基金supported by the National Natural Science Foundation of China(Grant Nos.10904083 and 10904084)the Project of Shandong Provincial Higher Educational Science and Technology Program(Grant No.J13LA05)the Excellent Young Scholars Research Fund of Shandong Normal University
文摘A double T-shaped device model is constructed to investigate the spin polarized current injection and transportation properties in organic semiconductors.Based on the spin diffusion theory and Ohm’s law and considering the different charge-spin relationship of the special carriers in organic semiconductors,the current spin polarization has been obtained.Effects of the branch current ratio and the polaron proportion on the spin polarized current injection efficiency are studied.From the calculation,it is found that the improvement of the spin polarized current injection efficiency can be obtained by adjusting the branch current ratio;moreover,high polaron proportion in organic semiconductors is beneficial for obtaining high current spin polarization.
基金The authors gratefully acknowledge the financial support of the National Natural Science Foundation of China (Nos. 51102194, 51323011, and 51121092), the Doctoral Program of the Ministry of Education (No. 20110201120040) and the Nano Research Program of Suzhou City (ZXG2013003). S. Shen is supported by the Foundation for the Author of National Excellent Doctoral Dissertation of China (No. 201335) and the Fundamental Research Funds for the Central Universities.
文摘Utilization of visible light is of crucial importance for exploiting efficient semiconductor catalysts for solar water splitting. In this study, an advanced ion implantation method was utilized to dope Cu ions into ZnO nanorod arrays for photoelectrochemical water splitting in visible light. X-ray diffraction (XRD) and X-ray photo-electron spectroscopy (XPS) results revealed that Cu^+ together with a small amount of Cu^2+ were highly dispersed within the ZnO nanorod arrays. The Cu ion doped ZnO nanorod arrays displayed extended optical absorption and enhanced photoelectrochemical performance under visible light illumination (A 〉 420 nm). A considerable photocurrent density of 18 μA/cm^2 at 0.8 V (vs. a saturated calomel electrode) was achieved, which was about 11 times higher than that of undoped ZnO nanorod arrays. This study proposes that ion implantation could be an effective approach for developing novel visible-light-driven photocatalytic materials for water splitting.