Al2O3/R141b ＋ Span-80 nanorefrigerant for 0.05 wt.% to 0.4 wt.% is prepared by ultrasonic vibration to investigate the influence of nanoparticle concentrations on flow boiling heat transfer of Al2O3/R141b ＋ Span-80...Al2O3/R141b ＋ Span-80 nanorefrigerant for 0.05 wt.% to 0.4 wt.% is prepared by ultrasonic vibration to investigate the influence of nanoparticle concentrations on flow boiling heat transfer of Al2O3/R141b ＋ Span-80 in micro heat exchanger by direct metal laser sintering. Experimental results show that nanoparticle concentrations have significantly impact on heat transfer coefficients by homogeneity test of variances according to mathematical statistics. The heat transfer performance of Al2O3/R141b ＋ Span-80 nanorefrigerant is enhanced after adding nanoparticles in the pure refrigerant R141b. The heat transfer coefficients of 0.05 wt.%, 0.1 wt.%, 0.2 wt.%, 0.3 wt.% and 0.4 wt.% Al2O3/R141 b ＋ Span-80 nanorefrigerant respectively increase by 55.0% 72.0%, 53.0% 42.3% and 39.9% compared with the pure refrigerant R141b. The particle fluxes from viscosity gradient, non-uniform shear rate and Brownian motion cause particles to migrate in fluid especially in the process of flow boiling. This migration motion enhances heat transfer between nanoparticles and fluid. Therefore, the heat transfer performance of nanofluid is enhanced. It is important to note that the heat transfer coefficients nonlinearly increase with nanoparticle concentrations increasing. The heat transfer coefficients reach its maximum value at the mass concentration of 0.1% and then it decreases slightly. There exists an optimal mass concentration corresponding to the best heat transfer enhancement. The reason for the above phenomenon is attributed to nanoparticles deposition on the minichannel wall by Scanning Electron Microscopy observation. The channel surface wettability increases during the flow boiling experiment in the mass concentration range from 0.2 wt.% to 0.4 wt.%. The channel surface with wettability increasing needs more energy to produce a bubble. Therefore, the heat transfer coefficients decrease with nanopartide concentrations in the range from 0.2 wt.% to 0.4 wt.%. In addition, a new correlation has been proposed by fitting the experimental data considering the influence of mass concentrations on the heat trans- fer performance. The new correlation can effectively predict the heat transfer coefficient.展开更多
This study investigated the heat transfer and flow characteristics of one kind of swirlgenerator in a circular heat exchanger tube through a numericalsimulation. The swirlflow induced by this type of swirlgenerator ca...This study investigated the heat transfer and flow characteristics of one kind of swirlgenerator in a circular heat exchanger tube through a numericalsimulation. The swirlflow induced by this type of swirlgenerator can obtain a high heat transfer rate with minimalpressure drop penalty. The simulations were carried out to understand the physicalbehavior of this kind of mesoscale heat enhancement component. By visualizing the heat transfer and flow characteristics, it is found that the swirlflow is induced by swirlgenerator in the circular tube couples with the impinging jet effect. After passing through the swirlgenerator, the localfriction factor of liquid can quickly return to lower levelmore quickly, while the localNusselt number maintains higher values for a distance; thus, the evaluation criterion of localperformance is improved. Single-factor optimization is used for three geometric parameters, i.e., the angle of swirlgenerator(25o, 45o, and 60o), the length of swirlgenerator(0.005, 0.01, and 0.02 m), and the center rod radius(1, 2, and 3 mm). The optimum parameters of the swirlgenerator for laminar flow of air in a circular tube are obtained, which should be 60o, 0.005 m, and 3 mm, respectively.展开更多
To enhance seamless source mobility support in the mobile NDN(Named Data Networking) environment,we propose a novel Locator Based Mobility support Approach,dubbed LBMA.In this approach,we assign a unique topologically...To enhance seamless source mobility support in the mobile NDN(Named Data Networking) environment,we propose a novel Locator Based Mobility support Approach,dubbed LBMA.In this approach,we assign a unique topologically layered locator to each AR(Access Route)in NDN network,and extend the AR with additional functionalities,such as caching and forwarding Interest packets on behalf of the source.Meanwhile,we add an optional field to the original NDN packet,and modify the Outgoing Interface(s) field in the AR's original FIB(Forwarding Information Base)entries,to record the mobility status and the current locator of the source.Specifically,the consumer in LBMA can continue the interrupted communication,without delivering Interest packets towards the old location of the source,nor waiting for all relevant devices completing the FIB entries updating.The performance analysis result indicates that LBMA has lower handoff cost and shorter handoff latency,compared with other existing source mobility support approaches.展开更多
基金Supported by the National Natural Science Foundation of China[21276090]
文摘Al2O3/R141b ＋ Span-80 nanorefrigerant for 0.05 wt.% to 0.4 wt.% is prepared by ultrasonic vibration to investigate the influence of nanoparticle concentrations on flow boiling heat transfer of Al2O3/R141b ＋ Span-80 in micro heat exchanger by direct metal laser sintering. Experimental results show that nanoparticle concentrations have significantly impact on heat transfer coefficients by homogeneity test of variances according to mathematical statistics. The heat transfer performance of Al2O3/R141b ＋ Span-80 nanorefrigerant is enhanced after adding nanoparticles in the pure refrigerant R141b. The heat transfer coefficients of 0.05 wt.%, 0.1 wt.%, 0.2 wt.%, 0.3 wt.% and 0.4 wt.% Al2O3/R141 b ＋ Span-80 nanorefrigerant respectively increase by 55.0% 72.0%, 53.0% 42.3% and 39.9% compared with the pure refrigerant R141b. The particle fluxes from viscosity gradient, non-uniform shear rate and Brownian motion cause particles to migrate in fluid especially in the process of flow boiling. This migration motion enhances heat transfer between nanoparticles and fluid. Therefore, the heat transfer performance of nanofluid is enhanced. It is important to note that the heat transfer coefficients nonlinearly increase with nanoparticle concentrations increasing. The heat transfer coefficients reach its maximum value at the mass concentration of 0.1% and then it decreases slightly. There exists an optimal mass concentration corresponding to the best heat transfer enhancement. The reason for the above phenomenon is attributed to nanoparticles deposition on the minichannel wall by Scanning Electron Microscopy observation. The channel surface wettability increases during the flow boiling experiment in the mass concentration range from 0.2 wt.% to 0.4 wt.%. The channel surface with wettability increasing needs more energy to produce a bubble. Therefore, the heat transfer coefficients decrease with nanopartide concentrations in the range from 0.2 wt.% to 0.4 wt.%. In addition, a new correlation has been proposed by fitting the experimental data considering the influence of mass concentrations on the heat trans- fer performance. The new correlation can effectively predict the heat transfer coefficient.
基金supported by the National Science and Technology Major Project of the Ministry of Science and Technology of China (No. 2016YFC0400406)
文摘This study investigated the heat transfer and flow characteristics of one kind of swirlgenerator in a circular heat exchanger tube through a numericalsimulation. The swirlflow induced by this type of swirlgenerator can obtain a high heat transfer rate with minimalpressure drop penalty. The simulations were carried out to understand the physicalbehavior of this kind of mesoscale heat enhancement component. By visualizing the heat transfer and flow characteristics, it is found that the swirlflow is induced by swirlgenerator in the circular tube couples with the impinging jet effect. After passing through the swirlgenerator, the localfriction factor of liquid can quickly return to lower levelmore quickly, while the localNusselt number maintains higher values for a distance; thus, the evaluation criterion of localperformance is improved. Single-factor optimization is used for three geometric parameters, i.e., the angle of swirlgenerator(25o, 45o, and 60o), the length of swirlgenerator(0.005, 0.01, and 0.02 m), and the center rod radius(1, 2, and 3 mm). The optimum parameters of the swirlgenerator for laminar flow of air in a circular tube are obtained, which should be 60o, 0.005 m, and 3 mm, respectively.
基金ACKNOWLEDGEMENT This work was partially supported by the National Basic Research Program of China （973 program） under Grant No. 2013CB329100 National Natural Science Foundation of China under Grants No. 61271200, No. 61232017, No. 61271202+1 种基金 National S＆T Major Program under Grant No. 2012ZX03005003 the Doctoral Fund of Ministry of Education of China under Grant No. 20130009110014, and the Program for New Century Excellent Talents in University （NCET） under Grant No. NCET-12-0767.
文摘To enhance seamless source mobility support in the mobile NDN(Named Data Networking) environment,we propose a novel Locator Based Mobility support Approach,dubbed LBMA.In this approach,we assign a unique topologically layered locator to each AR(Access Route)in NDN network,and extend the AR with additional functionalities,such as caching and forwarding Interest packets on behalf of the source.Meanwhile,we add an optional field to the original NDN packet,and modify the Outgoing Interface(s) field in the AR's original FIB(Forwarding Information Base)entries,to record the mobility status and the current locator of the source.Specifically,the consumer in LBMA can continue the interrupted communication,without delivering Interest packets towards the old location of the source,nor waiting for all relevant devices completing the FIB entries updating.The performance analysis result indicates that LBMA has lower handoff cost and shorter handoff latency,compared with other existing source mobility support approaches.
