磁铁矿岩的流变与磁化率各向异性

在高温高压及慢应变率下使磁铁矿岩样品发生了流变。对此过程前后的磁性测试表明，产生了与流变过程相关的磁化率各向异性。进一步研究说明，这种“流变磁效应”，主要是由于岩样内磁性矿物颗粒在流变过程中，由大致等粒形且方向性不明显而转变为扁椭球形且具有了一定优选方位而造成的。地震孕育是在高温、高压及缓慢的时间过程中进行的，因此研究流变带来的物性变化对于地震前兆的认识至关重要。本实验结果从一个新的角度探索地震磁效应，具有理论和实际意义。

某深基坑工程监测与流变效应分析

通过对某软土地基深基坑工程监测资料的分析 ,尤其是详细考察了该基坑变形的过程 ,得出了一些变形的规律。用深层土体位移资料详细地分析了土体流变效应 ,经过曲线拟合 ,得到软土的流变率。这将对施工起到一定的指导作用 ,亦可作为对软土流变效应的研究提供参考。

Flow behavior and microstructure of ZK60 magnesium alloy compressed at high strain rate

Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.

Effect of Zr and Sc on mechanical properties and electrical conductivities of Al wires

In order to obtain the Al wires with good mechanical properties and high electrical conductivities, conductive wires of Al-0.16 Zr, Al-0.16 Sc, Al-0.12Sc-0.04Zr（mass fraction, %） and pure Al（99.996%） were produced with the diameter of 9.5 mm by continuous rheo-extrusion technology, and the extruded materials were heat treated and analyzed. The results show that the separate additions of 0.16% Sc and 0.16% Zr to pure Al improve the ultimate tensile strength but reduce the electrical conductivity, and the similar trend is found in the Al-0.12Sc-0.04 Zr alloy. After the subsequent heat treatment, the wire with the optimum comprehensive properties is Al-0.12Sc-0.04 Zr alloy, of which the ultimate tensile strength and electrical conductivity reach 160 MPa and 64.03%（IACS）, respectively.

A Statistical Method for Characterizing CMOS Process Fluctuations in Subthreshold Current Mirrors

A novel method to characterize CMOS process fluctuations in subthreshold current mirrors （SCM） is reported. The proposed model is succinct in methodology and calculation complexity compared with previous statistical models. However,it provides favorable estimations of CMOS process fluctuations on the SCM circuit, which makes it promising for engineering applications. The model statistically abstracts physical parameters, which depend on the IC process, into random variables with certain mean values and standard deviations, while aggregating all the random impacts into a discrete martingale. The correctness of the proposed method is experimentally verified on an SCM circuit implemented in an SMIC 0.18μm CMOS 1P6M mixed signal process with a conversion factor of 100 in an input range from 100pA to lμA. The pro- posed theory successfully predicts - 10% of die-to-die fluctuation measured in the experiment, and also suggests the -lmV of threshold voltage standard deviation over a single die,which meets the process parameters suggested by the design kit from the foundry. The deviations between calculated probabilities and measured data are less than 8%. Meanwhile, pertinent suggestions concerning high fluctuation tolerance subthreshold analog circuit design are also made and discussed.

Relationship between rheological behavior and flotation rate in slurry with different chalcopyrite and lizardite concentration

The relationship between viscosity/yield stress and flotation rate in different chalcopyrite and lizardite concentrations was investigated by zeta potential measurements,rheological tests,flotation experiments,and DerjguinLandau-Verwey-Overbeek theoretical calculation.Results indicated that the concentration of minerals would affect the viscosity and yield stress of the slurry.That is,the viscosity/yield stress in the slurry rises accordingly when the concentration of minerals increases.The increase in viscosity/yield stress in slurry is also unfavorable to the enrichment of chalcopyrite but is conducive to the entrainment of lizardite in either single or binary system.Specifically,the flotation rate of chalcopyrite decreases while that of lizardite increases with the rise in viscosity/yield stress.

Intraseasonal variability of summer monsoon rainfall over the lower reaches of the Yangtze River basin

This work investigates the boreal-summer intraseasonal variability(ISV)of the precipitation over the lower reaches of the Yangtze River basin(LYRB)during 1979–2016,based on daily Climate Prediction Center global precipitation data.The ISV of the summer monsoon rainfall over the LYRB is mainly dominated by the lower-frequency 12–20-day variability and the higher-frequency 8–12-day variability.The lower-frequency variability is found to be related to the northwestwardpropagating quasi-biweekly oscillation(QBWO)over the western North Pacific spanning the South China Sea(SCS)and Philippine Sea,while the higher-frequency variability is related to the southeastward propagating midlatitude wave train(MLWT).Moreover,not each active QBWO(MLWT)in the SCS(East Asia)can generate ISV components of the precipitation anomaly over the LYRB.The QBWO can change the rainfall significantly with the modulation of mean state precipitation,while the quasi-11-day mode mainly depends on the intensity of the MLWT rather than the mean precipitation change.These findings should enrich our understanding of the ISV of the East Asian summer monsoon and improve its predictability.

Flow behavior and fracture of Al−Mg−Si alloy at cryogenic temperatures

The tensile and fracture behaviors of AA6061 alloy were investigated in order to provide quantitative data about this alloy at cryogenic temperatures.Specimens of AA6061 alloy were solution heat treated before tensile tests at 298,173 and 77 K and tested at strain rates in the range from 0.1 to 0.0001 s^(−1).The results indicate the suppression of the Portevin−Le Chatelier(PLC)effect and dynamic strain aging(DSA)at 77 K.In contrast,at 298 K,a remarkable serrated flow,characteristic of the PLC effect,is observed.Furthermore,the tensile behavior at 77 K,compared with that observed at 173 and 298 K,shows a simultaneous increase in strength,uniform elongation,modulus of toughness,strain-hardening exponent and strain rate sensitivity,which is related to a decrease in the dynamic recovery rate at low temperature.These responses are reflected on the fracture morphology,since the dimple size decreases at 77 K,while the area covered by dimples increases.Comparisons of the Johnson−Cook model show that a good agreement can be obtained for tests at 173 and 77 K,in which DSA is suppressed.

Constitutive analysis of AZ31 magnesium alloy plate

The plastic deformation simulation of AZ31 magnesium alloy at different elevated temperatures （from 473 to 723 K） was performed on Gleeble-1500 thermal mechanical simulator at the strain rates of 0.01, 0.1, 1, 5 and 10 s-t and the maximum deformation degree of 80%. The relationship between the flow stress and deformation temperature as well as strain rate was analyzed. The materials parameters and the apparent activation energy were calculated. The constitutive relationship was established with a Zener-Hollomon （Z） parameter. The results show that the flow stress increases with the increase of strain rate at a constant temperature, but it decreases with the increase of deformation temperature at a constant strain rate. The apparent activation energy is estimated to be 129-153 kJ/mol, which is close to that for self-diffusion of magnesium. The established constitutive relationship can reflect the change of flow stress during hot deformation.

Flow stress behavior of high-purity Al-Cu-Mg alloy and microstructure evolution

The flow stress behavior of high-purity Al-Cu-Mg alloy under hot deformation conditions was studied by Gleeble-1500,with the deformation temperature range from 300 to 500 °C and the strain rate range from 0.01 to 10 s-1. From the true stress-true strain curve, the flow stress increases with the increasing of strain and tends to be constant after a peak value, showing dynamic recover, and the peak value of flow stress increases with the decreasing of deformation temperature and the increasing of strain rate.When the strain rate is 10 s-1 and the deformation temperature is higher than 400 °C, the flow stress shows dynamic recrystallization characteristic. TEM micrographs were used to reveal the evolution of microstructures. According to the processing map at true strain of 0.7, the feasible deformation conditions are high strain rate(>0.5 s-1) or 440-500 °C and 0.01-0.02 s-1.

Viscosity profile prediction of a heavy crude oil during lifting in two deep artesian wells

It has been known that the productivity of artesian wells is strongly dependent on the rheological properties of crude oils. This work targets two deep artesian wells(>5000 m) that are producing heavy crude oil. The impacts of well conditions including temperature, pressure and shear rate, on the crude oil rheology were comprehensively investigated and correlated using several empirical rheological models. The experimental data indicate that this heavy oil is very sensitive to temperature as result of microstructure change caused by hydrogen bonding. The rheological behavior of the heavy oil is also significantly impacted by the imposed pressure, i.e., the viscosity flow activation energy(Eμ) gently increases with the increasing pressure. The viscosity–shear rate data are well fitted to the power law model at low temperature. However, due to the transition of fluid feature at high temperature(Newtonian fluid), the measured viscosity was found to slightly deviate from the fitting data. Combining the evaluated correlations, the viscosity profile of the heavy crude oil in these two deep artesian wells as a function of well depth was predicted using the oilfield producing data.

Millennial-centennial Scales Climate Changes of Holocene Indicated by Magnetic Susceptibility of High-resolution Section in Salawusu River Valley, China

The upmost segment （Holocene series） of the Milanggouwan stratigraphic section （MGS 1） in the Salawusu River valley shows 11 sedimentary cycles of dune sands and fluvio-lacustrine facies, or dune sands and paleosols. The analysis of the magnetic susceptibility of this segment suggests that there are 11 magnetic susceptibility cycles with the value alternating from low to high, in which the layers of the dune sands correspond to the lower value of the magnetic susceptibility and the layers of fluvio-lacustrine facies and paleosols correspond to the higher peaks. The study reveals that the low and high magnetic susceptibility values indicate the climate dominated by cold-arid winter monsoon and warm-humid summer monsoon of East Asia, respectively, and the study area has experienced at least 22 times of milleunial-centennial scales climate alternation from the cold-arid to the warm-humid during the Holocene. In terms of the time and the climate nature, the variations basically correspond to those of the North Atlantic and some records of cold-warm changes in China as well. They might be caused by the alternation of winter and summer monsoons in the Mu Us Desert induced by global climate fluctuations in the Holocene.

Development of aluminum rheo-extrusion process using semi-solid slurry at low solid fraction

An aluminum extrusion process is mainly used to fabricate long tubes, beams and rods for various applications. However, this process has a high production cost due to the need for investment of high-pressure machinery. The objective of this work is to develop a new semi-solid extrusion process using semi-solid slurry at low solid fractions. A laboratory extrusion system was used to fabricate aluminum rods with the diameter of 12 ram. The semi-solid metal process used in this study was the gas induced semi-solid （GISS） technique. To study the feasibility of the GISS extrusion process, the effects of extrusion parameters such as plunger speed and solid fi-action on the extrudability, microstructure, and mechanical properties of extruded samples were investigated. The results show that the plunger speed and solid fraction of the semi-solid metal need to be carefully controlled to produce complete extruded parts.

Hot compressive deformation behavior and constitutive relationship of Al-Zn-Mg-Zr alloy with trace amounts of Sc

Abstract： The hot deformation behaviors of AI-Zn-Mg-Sc-Zr alloy were investigated in a temperature range of 340-500℃ and a strain rate range of 0.001-10 s 1 using uniaxial compression test on Gleeble-1500 thermal simulation machine. The results show that the flow stress increases with increasing strain and tends to be constant after a peak value. The flow stress increases with increasing strain rate and decreases with increasing deformation temperature. The phenomenon of dynamic recovery and dynamic recrystallization can be observed by microstructural evolutions. Based on the hyperbolic Arrhenius-type equation, the true stress-true strain data from the tests were employed to establish the constitutive equation considering the effect of the true strain on material constants （α, β, Q, n and A）, which reveals the dependence of the flow stress on strain, strain rate and deformation temperature. The predicted stress-strain curves are in good agreement with experimental results, which confirms that the developed constitutive equations are suitable to research the hot deformation behaviors of Al-Zn-Mg-Sc-Zr alloy.

Hot deformation behavior and constitutive relationship of Q420qE steel

Isothermal compression tests at temperatures from 1 273 to l 423 K and strain rates from 0.1 to 10 s-q were carried out to investigate the flow behaviors of Q420qE steel. Stress-strain data collected from the tests were employed to establish the constitutive equation, in which the influence of strain was incorporated by considering the effect of strain on material constants Q, n, a, and lnA. The results show that the flow stress curves are dependent on the strain, strain rate and deformation temperature. They display typical dynamic recrystallization behavior and consist of three stages, i.e., hardening stage, softening stage and steady stage. The flow stress decreases with increasing the deformation temperature and decreasing the strain rate. In addition, the flow stress data predicted by the proposed constitutive model agree well with the corresponding experimental results, and the correlation coefficient and the average absolute relative error between them are 0.990 3 and 3.686%, respectively.

Scale-Free Properties in Traffic System

In this work, we propose a new model of evolution networks, which is based on the evolution of the traffic flow. In our method, the network growth does not take into account preferential attachment, and the attachment of new node is independent of the degree of nodes. Our aim is that employing the theory of evolution network, we give a further understanding about the dynamical evolution of the traffic flow. We investigate the probability distributions and scaling properties of the proposed model The simulation results indicate that in the proposed model, the distribution of the output connections can be well described by scale-free distribution. Moreover, the distribution of the connections is largely related to the traffic flow states, such as the exponential distribution （i.e., the scale-free distribution） and random distribution etc.

Plastic flow behavior of superalloy GH696 during hot deformation

In order to investigate the hot deformation behavior of superalloy GH696, isothermal compression experiments were carried out at deformation temperatures of 880?1120 °C and strain rates of 0.01?10 s?1. And the deformation amount of all the samples was 50%. The strain rate sensitivity exponent (m) and strain hardening exponent (n) under different deformation conditions were calculated, meanwhile the effects of the processing parameters on the values ofm andn were analyzed. The results show that the flow stress increases with the increase of strain rate and the decrease of deformation temperature. The value ofm increases with the increase of deformation temperature and decreases with the increase of strain rate, while the value ofn decreases with the increase of deformation temperature. A novel flow stress model during hot deformation of superalloy GH696 was also established. And the calculated flow stress of the alloy is in good agreement with the experimental one.

Dynamic recrystallization behavior and kinetics of high strength steel

The dynamic recrystallization behavior of high strength steel during hot deformation was investigated.The hot compression test was conducted in the temperature range of 950-1150 °C under strain rates of 0.1,1 and 5 s-1.It is observed that dynamic recrystallization(DRX) is the main flow softening mechanism and the flow stress increases with decreasing temperature and increasing strain rate.The relationship between material constants(Q,n,α and ln A) and strain is identified by the sixth order polynomial fit.The constitutive model is developed to predict the flow stress of the material incorporating the strain softening effect and verified.Moreover,the critical characteristics of DRX are extracted from the stress-strain curves under different deformation conditions by linear regression.The dynamic recrystallization volume fraction decreases with increasing strain rate at a constant temperature or decreasing deformation temperature under a constant strain rate.The kinetics of DRX increases with increasing deformation temperature or strain rate.

Effect of plunger number on hydraulic transformer's flow pulsation rate

In order to supply theoretical guidance to hydraulic transformer's design and application,the effect of the number of plungers in hydraulic transformer on its flow characteristic is analyzed,theoretical analysis and simulation are done on hydraulic transformer's flow characteristic when the number of plungers is different.Based on the working principle of swash plate piston hydraulic components,mathematical models of instantaneous flow and flow pulsation rate are built,and simulation study is done with MATLAB.As a result,the effect is found,and some conclusions worth referring to are obtained.

Creep properties and permeability evolution in triaxial rheological tests of hard rock in dam foundation

Triaxial creep tests were carried out under seepage pressure by using rock servo-controlled triaxial rheology testing equipment. Based on experimental results, rock rheological properties influenced by seepage-stress coupling were studied, and variations of seepage rate with time in complete creep processes of rock were analyzed. It is shown that, when the applied stress is less than failure stress level, the creep deformation is not obvious, and its main form is steady-state creep. When applied stress level is greater than or less than but close to fracture stress, it is easier to see the increase of creep deformation and the more obvious accelerative creep characteristics. The circumferential creep deformation is obviously higher than the axial creep deformation. At the stage of steady-state creep, the average of seepage flow rate is about 4.7×10-9 rn/s at confining pressure （tr3） of 2 MPa, and is about 3.9×10-9 m/s at a3 of 6 MPa. It is seen that the seepage flow rate at or3 of 2 MPa in this case is obviously larger than that at tr3 of 6 MPa. At the stage of creep acceleration, the seepage flow rate is markedly increased with the increase of time. The variation of rock permeability is directly connected to the growth and evolution of creep crack. It is suggested that the permeability coefficient in complete creep processes of rock is not a constant, but is a function of rock creep strain, confining pressure, damage variable and pore water pressure. The results can be considered to provide a reliable reference for the establishment of rock rheological model and parameter identification.