逆向流斜板沉淀池计算的新方法

本文根据流体力学原理,结合斜板沉淀池的结构特点,对干扰沉降条件下,颗粒在斜板流道中的沉降分离过程进行了分析、研究,从而建立了斜板沉淀池设计计算的新方法。

宽胶带运输机改造

由于宽胶带运输机设计不合理,运转中经常跑偏很难调整,机头机尾滚筒先后断裂,流料板需频繁清理.通过改造提高了设备作业率,缩短了抢修时间.

Effect of flow stress—strain relation on forming limit of 5754O aluminum alloy

A modified Swift type flow stress—strain relation was presented in order to describe the uniaxial tension test curve reasonably. The FLD-strain （forming limit diagram made up of limit strain） of 5754O aluminum alloy sheet was calculated based on the two flow stress—strain relations using Yld2000-2d yield function. By comparing the theoretical and experimental results, it is found that the calculated FLD-strain based on the modified Swift flow stress—strain relation can reasonably describe the experimental results. However, though the common Voce flow stress—strain relation can describe the deformation behavior during homogenous deformation phase accurately, the FLD-strain calculated based on it is obviously lower than the experimental result. It is concluded that the higher the hardening rate of sheet metal is, the higher the forming limit is. A method for determining the reasonable flow stress—strain relation is recommended for describing the material behavior during inhomogenous phase and the forming limit of sheet metal.

Study on Jet Coflow Packing Tray

Experimental study on hydrodynamics and mass transfer efficiencyof jet coflow packing tray (JCPT) was conducted in a φ285 mm columnand φ200 mm column, respectively. Compared with new vertical sievetray which has been applied in the petrochemical industry since 1968,the JCPT has lower pressure drop, higher capacity and higher masstransfer efficiency, and seems promising in commercial application.

Anti-flooding of polymer electrolyte membrane fuel cell with in-plate adverse-flow flow-field

The stoichiometric ratios and related regimes, which can promote anti-flooding of polymer electrolyte membrane fuel cell （PEMFC） with in-plate adverse-flow flow-field （IPAF）, were investigated. Two flow combinations, which are the simple and complex adverse-flow between plates （ABP） that can be realized by IPAF, were employed. Constant stoichiometric ratios examination indicates that the complex ABP could improve anti-flooding of PEMFC better in the medium （greater than 200 mA/cm2 and less than 1 000 mA/cm2） and high （greater than 1 000 mA/cm2） current densities than the simple ABP. More stoichiometric ratios were introduced to find the cathode critical stoichiometry. Under the condition of cathode critical stoichiometry, the maximal local relative humidity of both electrodes of complex ABP is equal to 100% and below while the anti-flooding of the cathode of simple ABP is not satisfactory in the medium and high current densities. Further study shows that the mechanism of fuel cell, which is the imerdependence between the electrodes effect, can make significant contribution to anti-flooding.

Fabrication of micro-flow channels on graphite composite bipolar plates using microplaning

A new method of manufacturing micro-flow channels on graphite composite bipolar plate(GCBPP) microplaning using specially designed multi-tooth tool is proposed. In this method, several or even dozens of parallel micro-flow channels ranging from 100 μm to 500 μm in width can be produced simultaneously. But, edge chippings easily occur on the rib surface of GCBPP during microplaning due to brittleness of graphite composites. Experimental results show that edge chippings result in the increase of contact resistance between bipolar plate and carbon paper at low compaction force. While the edge chippings scarcely exert influence on the contact resistance at high compaction force. Contrary to conventional view, the edge chippings can significantly improve performance of microfuel cell and big edge chippings outperform small edge chippings. In addition, the influence of technical parameters on edge chippings was investigated in order to obtain big, but not oversized edge chippings.