彩色套药生产流程中S_2O_3^(2-)、SO_3^(2-)在线分析法研究

提出了一种S_2O_3^(2-)和SO_3^(2-)生产流程在线分析方法,方法简便,连续采样、连续测定、浓度范围250～550 g/L,响应时间98 s,1.5 h漂移<0.15。

Traffic-aware static channel assignment algorithm in wireless mesh networks

A channel assignment algorithm with awareness of link traffic is proposed in multi-radio multi-channel wireless mesh networks. First, the physical interference model based on the signal-to-interference-plus-noise ratio and successful transmission condition is described. The model is more suitable for a wireless communication environment than other existing models. Secondly, a pure integer quadratic programming （PIQP） model is used to solve the channel assignment problem and improve the capacity of wireless mesh networks. Consequently, a traffic- aware static channel assignment algorithm（TASC） is designed. The algorithm adopts some network parameters, including the network connectivity, the limitation of the number of radios and the successful transmission conditions in wireless communications. The TASC algorithm can diminish network interference and increase the efficiency of channel assignment while keeping the connectivity of the network. Finally, the feasibility and effectivity of the channel assignment solution are illustrated by the simulation results. Compared witb similar algorithms, the proposed algorithm can increase the capacity of WMNs.

A Novel ADC Architecture for Digital Voltage Regulator Module Controllers

The design and implementation of a novel ADC architecture called ring-ADC for digital voltage regulator module controllers are presented. Based on the principle of voltage-controlled oscillators＇ transform from voltage to frequency,the A/D conversion of ring-ADC achieves good linearity and precise calibration against process variations compared with the delay-line ADC. A differential pulse counting discriminator also helps decrease the power consumption of the ring-ADC. It is fabricated with a Chartered 0.35μm CMOS process, and the measurement results of the integral and differential nonlinearity performance are 0.92LSB and 1.2LSB respectively. The maximum gain error measured in ten sample chips is ± 3.85%. With sampling rate of 500kHz and when the voltage regulator module （VRM） works in steady state, the ring-ADC＇s average power consumption is 2.56mW. The ring-ADC is verified to meet the requirements for digital VRM controller application.

Isothermal extrusion speed curve design for porthole die of hollow aluminium profile based on PID algorithm and finite element simulations

The isothermal extrusion process of hollow aluminium profile was investigated using incremental proportional-integral-derivative(PID)control algorithm and finite element simulations.The range of extrusion speed was determined by considering the maximum extrusion load and production efficiency.By taking the optimal solution temperature of the secondary phase as the target temperature,the extrusion speed–stroke curve for realizing the isothermal extrusion of the aluminium profile was obtained.Results show that in the traditional constant extrusion speed process,the average temperature of the cross-section of the aluminium profile at the die exit rapidly increases and then slowly rises with the increase in ram displacement.As the extrusion speed increases,the temperature difference at the die exit of the profile along the extrusion direction increases.The exit temperature difference between the front and back ends of the extrudate along the extrusion direction obtained by adopting isothermal extrusion is about 6.9℃.Furthermore,the heat generated by plastic deformation and friction during extrusion is balanced with the heat transfer from the workpiece to the container,porthole die and external environment.

On the hydrodynamic stability of a particle-laden flow in growing flat plate boundary layer

The parabolized stability equation (PSE) was derived to study the linear stability of particle-laden flow in growing Blasius boundary layer. The stability characteristics for various Stokes numbers and particle concentrations were analyzed after solving the equation numerically using the perturbation method and finite difference. The inclusion of the nonparallel terms produces a reduction in the values of the critical Reynolds number compared with the parallel flow. There is a critical value for the effect of Stokes number, and the critical Stokes number being about unit, and the most efficient instability suppression takes place when Stokes number is of order 10. But the presence of the nonparallel terms does not affect the role of the particles in gas. That is, the addition of fine particles (Stokes number is much smaller than 1) reduces the critical Reynolds number while the addition of coarse particles (Stokes number is much larger than 1) enhances it. Qualitatively the effect of nonparallel mean flow is the same as that for the case of plane parallel flows.

Nonlinear Analysis of Flexible and Steel Catenary Risers with Internal Flow and Seabed Interaction Effects

Flexible risers and steel catenary risers often provide unique riser solutions for today’s deepwater field development. Accurate analysis of these slender structures, in which there are high-speed HP/HT internal flows, is critical to ensure personnel and asset safety. In this study, a special global coordinate-based FEM rod model was adopted to identify and quantify the effects of internal flow and hydrostatic pressure on both flexible and deepwater steel catenary risers, with emphasis on the latter. By incorporating internal flow induced forces into the model, it was found that the internal flow contributes a new term to the effective tension expression. For flexible risers in shallow water, internal flow and hydrostatic pressure made virtually no change to effective tension by merely altering the riser wall tension. In deep water the internal pressure wielded a dominant role in governing the riser effective tension and furthering the static configuration, while the effect of inflow velocity was negligible. With respect to the riser seabed interaction, both the seabed support and friction effect were considered, with the former modeled by a nonlinear quadratic spring, allowing for a consistent derivation of the tangent stiffness matrix. The presented application examples show that the nonlinear quadratic spring is, when using the catenary solution as an initial static profile, an efficient way to model the quasi-Winkler-type elastic seabed foundation in this finite element scheme.

A Priori and A Posteriori Error Estimates of Streamline Diffusion Finite Element Method for Optimal Control Problem Governed by Convection Dominated Diffusion Equation

In this paper,we investigate a streamline diffusion finite element approxi- mation scheme for the constrained optimal control problem governed by linear con- vection dominated diffusion equations.We prove the existence and uniqueness of the discretized scheme.Then a priori and a posteriori error estimates are derived for the state,the co-state and the control.Three numerical examples are presented to illustrate our theoretical results.

Development of a New Index for Integrating Landscape Patterns with Ecological Processes at Watershed Scale

Understanding the relationship between landscape pattems and ecological processes has been a central yet challenging research theme in landscape ecology. Over the past decades, many landscape metrics have been proposed but few directly incorporated ecological processes. In this paper, we developed a landscape index, namely, location-weighted landscape index （LWLI） to highlight the role of landscape type in ecological processes, such as nutrient losses and soil erosion. Within the framework of the Lorenz curve theory, we develop this index by integrating land- scape pattern and point-based measurements at a watershed scale. The index can be used to characterize the contribution of landscape pattern to ecological processes （e.g. nutrient losses） with respect to a specific monitoring point in a watershed. Through a case study on nutrient losses in an agricultural area in northeastern China, we found that nutrient losses tended to be higher for a watershed with a higher LWLI value, and vice versa. It implied that LWLI can be used to evaluate the potential risk of nutrient losses or soil erosion by comparing their values across watersheds. In addition, this index can be extended to characterize ecological processes, such as the effect of landscape pattern on wildlife inhabitation and urban heat island effect. Finally, we discuss several problems that should be paid attention to when applying this index to a heterogeneous landscape site.

Traffic Allocation Scheme with Cooperation of Multiple RANs in Universal Wireless Environments

This paper introduces an adaptive traffic allocation scheme with cooperation of multiple Radio Access Networks (RANs) in universal wireless environments.The different cooperation scenarios are studied,and based on the scenario of cooperation in both network layer and terminal layer,an open queuing system model,which is aiming to depict the characteristics of packet loss rate of wireless communication networks,is proposed to optimize the traffic allocation results.The analysis and numerical simulations indicate that the proposed scheme achieves inter-networking load balance tominimize the whole transmission delay and expands the communication ability of single-mode terminals to support high data rate traffics.

Wave Interaction with Dual Circular Porous Plates

In this paper we have investigated the reflection and the transmission of a system of two symmetric circular-arc-shaped thin porous plates submerged in deep water within the context of linear theory. The hypersingular integral equation technique has been used to analyze the problem mathematically. The integral equations are formulated by applying Green＇s integral theorem to the fundamental potential function and the scattered potential function into a suitable fluid region, and then using the boundary condition on the porous plate surface. These are solved approximately using an expansion-cure-collocation method where the behaviour of the potential functions at the tips of the plates have been used. This method ultimately produces a very good numerical approximation for the reflection and the transmission coefficients and hydrodynamic force components. The numerical results are depicted graphically against the wave number for a variety of layouts of the arc. Some results are compared with known results for similar configurations of dual rigid plate systems available in the literature with good agreement.

Prediction of multi-borehole undermine coalbed gas drainage

By analyzing the flow character of a single drainage borehole in its effectingtime and the correlative theory introduced,the reason for 'inflexion' appearance in theflow character curve of the single draining borehole in a multi-borehole was studied.Takingthe theory of permeation fluid mechanics and so on as basis,the coalbed gas flowmodel was set up,and the numerical simulation analyzer was built for undermine gasproducts.With the results from the analyzer,the gas capacity could be calculated underdifferent conditions and comparisons made with the site measurement data.

Topological Aspect and Bifurcation of Disclination Lines in Two—Dimensional Liquid Crystals

Using φ-mapping method and topological current theory, the topological structure and bifurcation ofdisclination lines in two-dimensional liquid crystals are studied. By introducing the strength density and the topologicalcurrent of many disclination lines, the total disclination strength is topologically quantized by the Hopf indices andBrouwer degrees at the singularities of the director field when the Jacobian determinant of director field does not vanish.When the Jacobian determinant vanishes, the origin, annihilation and bifurcation processes of disclination lines arestudied in the neighborhoods of the limit points and bifurcation points, respectively. The branch solutions at the limitpoint and the different directions of all branch curves at the bifurcation point are calculated with the conservation lawof the topological quantum numbers. It is pointed out that a disclination line with a higher strength is unstable and itwill evolve to the lower strength state through the bifurcation process.

Dual solutions of MHD stagnation point flow and heat transfer over a stretching/shrinking sheet with generalized slip condition

An analysis was made to study the steady momentum and heat transfer characteristics of a viscous electrically conducting fluid near a stagnation point due to a stretching/shrinking sheet in the presence of a transverse magnetic field and generalized slip condition. Two flow problems corresponding to the planar and axisymmetric stretching/shrinking sheet were considered. By means of similarity transformations, the obtained resultant nonlinear ordinary differential equations were solved numerically using a shooting method for dual solutions of velocity and temperature profiles. Some important physical features of the flow and heat transfer in terms of the fluid velocity, the temperature distribution, the skin friction coefficient and the local Nusselt number for various values of the controlling governing parameters like velocity slip parameter, critical shear rate, magnetic field, ratio of stretching/shrinking rate to external flow rate and Prandtl number were analyzed and discussed. An increase of the critical shear rate decreases the fluid velocity whereas the local Nusselt number increases. The comparison of the present numerical results with the existing literature in a limiting case is given and found to be in an excellent agreement.

Fast Multi-Pattern Matching Algorithm on Compressed Network Traffic

Pattern matching is a fundamental approach to detect malicious behaviors and information over Internet, which has been gradually used in high-speed network traffic analysis. However, there is a performance bottleneck for multi-pattern matching on online compressed network traffic(CNT), this is because malicious and intrusion codes are often embedded into compressed network traffic. In this paper, we propose an online fast and multi-pattern matching algorithm on compressed network traffic(FMMCN). FMMCN employs two types of jumping, i.e. jumping during sliding window and a string jump scanning strategy to skip unnecessary compressed bytes. Moreover, FMMCN has the ability to efficiently process multiple large volume of networks such as HTTP traffic, vehicles traffic, and other Internet-based services. The experimental results show that FMMCN can ignore more than 89.5% of bytes, and its maximum speed reaches 176.470MB/s in a midrange switches device, which is faster than the current fastest algorithm ACCH by almost 73.15 MB/s.

The Uniqueness and Nonexistent Results for Some Nonlinear Partial Equations on Riemannian Manifolds

The paper studies a class of nonlinear elliptic partial differential equations on a compact Riemannian manifold （M,g） with some curvature restriction. The authors try to prove some uniqueness and nonexistent results for the positive solutions of the equations concerned.

Study of Rotor Spun Basofil/Cotton Blended Yarn Quality Characteristics during Optimisation of Processing Parameters

Yarn quality characteristics are affected by processing parameters. A 36 tex rotor spun yarn of 50/50 Basofil/ cotton （B/C） blended yarn was spun, and the spinning process optimised for rotor speed, opening roller speed and twist factor. Selected yarn characteristics were studied during the optimization process. During the optimizations process yarn elongation and hairiness reduced with increase in rotor speed. Tenacity increased with increase of rotor speed. The increase in TF caused tenacity and CV of count to increase up to a peak and then started to decrease with further increase of TF.While TF caused an increase in yarn hairiness, elongation decreased to a minimum level and then started to increase with further increase of TF. CV of count and hairiness increased with increase in opening roller speed, but tenacity and elongation decreased with increase in opening roller speed. The optimization process yielded the optimum levels for rotor speed, opening roller speed and twist factor （TF） as 45,000 rpm, 6,500 rpm and 450 respectively. As per uster Standards the optimum yam showed good results for CV of count, CV of tenacity and thin places/km.

Typical application of Rogowski coils in inspection of electrobath

During the aluminum electrolytic roasting process,each component of the electrobath of aluminum performs unsteadily when the electrolytic bath is in the pre-roasting stage. It is important to monitor the currents of the anodes and the cathodes of the aluminum electrobath at regular intervals. Both practice and investigation indicate that Rogowski coil can be adopted to measure heavy direct current of the anodes and the cathodes of the aluminum electrobath. The paper not only introduces the typical application of the Rogowski coil to inspect the state of aluminum electrobath in the roasting process, but also analyzes the principles of the coil sensor including its dynamic properties and some important measurement results respectively. The optimal parameters of the coil can be simulated by means of an advanced simulation tool: simulink tools based on MATLAB soft environment. Based on the gathered current data, an even-current coefficient has been introduced, and the current curve can be drawn. Since they are applied in AL-Electrolyzing, it is possible to distinguish the anode of which the current is not evenly distributed, and to take adjusting measures over a period of time to ensure that the current is evenly distributed.

Intelligent Traffic Allocation Algorithm for Multiple Networks

In recent years, wireless communication systems have experienced tremendous growth in data traffic. Many capacity-enhancing techniques are applied to elevate the gap between the amount of traffic and network capacity, and more solutions are required to minimize the gap. Traffic allocation among multiple networks is regarded as one of the most effective methods to solve the problem. However, current studies are unable to derive the quantity of traffic that each network should carry. An intelligent traffic allocation algorithm for multiple networks is proposed to obtain the optimal traffic distribution. Multiple factors affecting traffic distribution are considered in the proposed algorithm, such as network coverage, network cost, user habit, service types, network capacity and terminals. Using evaluations, we proved that the proposed algorithm enables a lower network cost than load balancing schemes. A case study of strategy rmldng for a 2G system refarming is presented to further illustrate the applicability of the proposed algorithm. We demonstrated that the new algorithm could be applied in strategy rmldng for telecommunication operators.

Investigation on a vertical radial flow adsorber designed by a novel parallel connection method

Due to the increasing global demand for industrial gas, the development of large-scale cryogenic air separation systems has attracted considerable attention in recent years. Increasing the height of the adsorption bed in a vertical radial flow adsorber used in cryogenic air separation systems may efficiently increase the treatment capacity of the air in the adsorber. However, uniformity of the flow distribution of the air inside the adsorber would be deteriorated using the height-increasing method. In order to reduce the non-uniformity of the flow distribution caused by the excessive height of adsorption bed in a vertical radial flow adsorber, a novel parallel connection method is proposed in the present work. The experimental apparatus is designed and constructed; the Computational Fluid Dynamics(CFD) technique is used to develop a CFD-based model, which is used to analyze the flow distribution, the static pressure drop and the radial velocity in the newly designed adsorber. In addition, the geometric parameters of annular flow channels and the adsorption bed thickness of the upper unit in the parallelconnected vertical radial flow adsorber are optimized, so that the upper and lower adsorption units could be penetrated by air simultaneously. Comparisons are made between the height-increasing method and the parallel connection method with the same adsorber height. It is shown that using the parallel connection method could reduce the difference between the maximum and minimum radial static pressure drop by 86.2% and improve the uniformity by 80% compared with those of using the height-increasing method. The optimal thickness ratio of the upper and lower adsorption units is obtained as 0.966, in which case the upper and lower adsorption units could be penetrated by air simultaneously, so that the adsorbents in adsorption space could be used more efficiently.

MmB DIFFERENCE SCHEMES FOR TWODIMENSIONAL HYPERBOLIC CONSERVATION LAWS

A new class of second order accuracy semidiscrete difference schemes is presented for the two-dimensional nonlinear scalar hyperbolic conservation laws. It is based on flux splitting, piecewise linear cell-averaged reconstruction and upwind property in the spatial discretization. By using TVD Runge-Kutta time discretization method, the full discrete scheme is obtained and its MmB property is proved. The extension to the two-dimensionalnonlinear hyperbolic conservation law systems is straightforward by using component-wise manner. The main advantage is simple: no Riemann problem is solved, and so field-by-field decomposition is avoided and the complicated computation is reduced. Numerical results of two-dimensional Euler equations of compressible gas dynamics verify the accuracy and robustness of the method.