广西国内旅游流流量与流质时空分布及差异分析

本文基于旅游流流量和流质指数,对广西及14个地市国内旅游流流量与流质时空分布及差异进行研究。结果表明:2003—2014年广西国内及14个地市旅游流流量呈逐步上升态势,旅游流流量的空间绝对差异越来越大,流量规模的空间相对差异总体较平稳,空间聚集度较高,首位分布较合理,流量位序变化呈"高位态势平稳,中低位间竞争激烈"的局面;国内旅游流流质指数逐年提高,由低质流向优质流转变;14个地市流质变化趋势呈逐步降低型、逐步改善型、平稳波动型和上升回落型4种类型,流量-流质匹配结构逐步优化,"小流量-高流质"类型城市数量不断增加,"小流量-低流质"类型城市数量减少,整体呈现良性发展态势。

Experimental Study on Gas-Solid Mass Transfer in Circulating Fluidized Beds

This study is devoted to gas-solid mass transfer behavior inheterogeneous two-phase flow. Experiments were carried out in a coldcirculating fluidized bed of 3.0 m in height and 72 mm in diameterwith naphthalene particles. Axial and radial distributions ofsublimated naphthalene concentration in air were measured with an on-line concentration monitoring system HP GC-MS. Mass transfercoefficients were obtained under various operating conditions,showing that heterogeneous flow structure strongly influences theaxial and radial profiles of mass transfer coefficients.

Power consumption and flow field characteristics of a coaxial mixer with a double inner impeller

A coaxial mixer meeting the actual demand of a system with high and variable viscosity is investigated. It has an outer wall-scraping frame and a double inner impeller consisting of a four-pitched-blade turbine and Rushton turbine. The power consumption and flow field characteristics of the coaxial mixer in laminar and transitional flow are simulated numerically, and then the distribution of velocity field, shear rate and mass flow rate are analyzed. The simulation results indicate that the outer frame has little effect on the power consumption of the double inner impeller whether in laminar or transitional flow, whereas the inner combined impeller has a great effect on the power consumption of the outer frame. Compared with the single rotation mode, the power consumption of the outer frame will decrease in co-rotation mode and increase in counter-rotation mode. The velocity, shear rate and mass flow rate are relatively high near the inner impeller in all operating modes, and only under double-shaft agitation will the mixing performance near the free surface be improved.In addition, these distributions in the co-rotation and counter-rotation modes show little difference, but the co-rotation mode is recommended for the advantage of low power consumption.

Diffusion Flame of a CH4/H2 Jet in a Hot Coflow： Effects of Coflow Oxygen and Temperature

This paper investigates the effects of coflow O2 level and temperature on diffusion flame of a CH4/H2 jet in hot coflow （JHC） from a burner system similar to that of Dally et al. The coflow O2 mass fraction （ Yo2 ） is varied from 3% to 80% and the temperature （Tcof） from 1200 K to 1700 K. The Eddy Dissipation Concept （EDC） model with detailed reaction mechanisms GRI-Mech 3.0 is used for all simulations. To validate the modeling, several JHC flames are predicted under the experimental conditions of Dally et al. [Proc. Combust. Inst., 29 （1）, 1147-1154 （2002）] and the results obtained match well with the measurements. Results demonstrate that, when Yo2 decreased, the diffusion combustion is likely to transform from traditional combustion to MILD （Moderate or Intense Low-oxygen Dilution） combustion mode. When Tcof is higher, the temperature distribution over the whole domain trends to be more uniform. Reducing yo2 or Tcof leads to less production of intermediate species OH and CO. It is worth noting that if Yo2 is high enough （ Yo2 〉80%）, increasing Yo2 does not cause obvious temperature increase.

A New Method for Measurement of Local Solid Flux in Gas-Solid Two-phase Flow

Previous works have shown that the suction probe cannot be used to accurately measure the upward and downward particle fluxes independently. A new method using a single optical probe to measure the local solid flux is presented. The measurement of upward, downward and net solid fluxes was carried out in a cold model circulating fluidized bed (CFB) unit. The result shows that the profile of the net solid flux is in good agreement with the previous experimental data measured with a suction probe. The comparison between the average solid flux determined with the optical measuring system and the external solid flux was made, and the maximum deviationturned out to be 22%, with the average error being about 6.9%. These confirm that the optical fiber system can be successfully used to measure the upward, downward and net solid fluxes simultaneously by correctly processing the sampling signals obtained from the optical measuring system.

Critical Heat Flux with Subcooled Flowing Water in Tubes for Pressures from Atmosphere to Near-Critical Point

During last 45 years, two groups of the experimental data on critical heat flux were obtained in bare tubes, covering the pressures from atmosphere to near-critical point. One group of the data were obtained in the inner diameter of 2.32, 5.16, 8.05, 10.0 and 16.0 mm, respectively, with the ranges of pressure of 0.1-1.92 MPa, velocity of 1.47-23.3 m/s, local subcooling of 3.7-108.7 ℃ and heat flux of up to 38.3 MW/m2. Another group of the data were obtained in the inner diameter of 4.62, 7.98 and 10.89 mm, respectively, with the ranges of pressure of 1.7-20.6 MPa, mass flux of 454-4,055 kg/（m2.s） and inlet subcooling of 53-361 ℃. The results showed complicated effects of the pressure, mass flux, subcooling and diameter on the critical heat flux. They were formulated by two empirical correlations. A mechanistic model on the limit of heat transfer capability from the bubbly layer to the subcooled core was also proposed for all the results.

Calculation of stratosphere–troposphere exchange in East Asia cut-off lows:cases from the Lagrangian perspective

In this study,the authors focus on the cut-off low pressure systems（COLs）lingering over East Asia in late spring and early summer and quantify the two-way stratosphere–troposphere exchange（STE）by 3D trajectory integrations,achieved using a revised version of the UK Universities Global Atmospheric Modelling Programme Offline Trajectory Code（Version 3）.By selecting 10 typical COLs and calculating the cross-tropopause air mass fluxes,it is found that stratosphere-to-troposphere transport（STT）fluxes exist in the center of COLs;and in the periphery of the COL center,troposphereto-stratosphere transport（TST）fluxes and STT fluxes are distributed alternately.Net transport fluxes in COLs are from stratosphere to troposphere,and the magnitude is about 10-4 kg m-2 s-1.The ratio between the area-averaged STT and TST fluxes increases with increasing strength of the COLs.By adopting appropriate residence time,the spurious transports are effectively excluded.Finally,the authors compare the results with previous studies,and find that the cross-tropopause fluxes（CTFs）induced by COLs are about one to two orders of magnitude larger than global CTFs.COLs play a significant role in local,rapid air mass exchanges,although they may only be responsible for a fraction of the total STE.

Trust assessment of business service workflow based on complex trust network

For business service workflow,QoS-based services selection can't guarantee whether the composite service satisfies user' s requirement after delivery,because once any service interrupts or quality of service(QoS) maliciously reduces,the quality of workflow will be reduced.Trustworthy services can provide reliable QoS,so trustworthiness research could improve the efficiency of services selection.This paper investigates trust assessment in the perspective of workflow.Firstly,trust network of business service workflow(TN-BSW) is proposed to analyze trust attributes;then,the trust measurement system of TN-BSW is investigated to assess the trust value quantitatively;and then,a trust-aware service recommendation model(TaSRM) is proposed to enhance the efficiency of QoS-basedservices selection;finally,experiment shows the feasibility of TN-BSWand the performance of TaSRM.

Influence of feature size of micro-scale channel on ink flow characteristics

Under the micro-scale condition,feature size of the channel is one of the main factors influencing the fluid flow characteristics. In printing process,ink thickness in the extrusion zone formed by two ink rollers may reach micron scale. Compared with macroscopic fluid,the velocity field and the pressure field of fluid may change when the feature size of fluid channel reaches micron scale. In order to control printing quality,it is necessary to research the influence of feature size on ink flow characteristics in micro scale. This paper analyzes it in theory,and then numerical simulation of an ink flow model with different feature sizes is carried out in no slip condition. The influence of the feature size on the ink flow characteristics and the wall shear force are obtained. Besides,the ink flow model with different feature sizes is simulated numerically in slip condition,and the influence of feature size on ink flow characteristics is obtained. Finally,by comparing and analyzing the above results,it can be concluded that both the ink velocity and pressure at the inlet of the extrusion zone are inversely proportional to the feature sizes whether in slip condition or not. And the ink velocity in slip condition is larger than that without slip,the pressure at the inlet of the extrusion zone is less than that in no slip condition. Within the micro-scale range,the ink velocity difference between the two conditions cannot be ignored. Therefore,it is necessary to consider slip when analyzing the influence of feature size of micro-scale channel on ink flow characteristics.

A Study on the Effects of the Intake Port Configurations on the Swirl Flow Generated in a Small D.I. Diesel Engine

This paper investigates the effect of intake port configuration on the swirl that is generated within a direct injection(D.I.) diesel engine. The in-cylinder flow characteristics are known to have significant effects on fuel-air mixing, combustion, and emissions. To clarify how to intensify the swirl flow, a swirl control valve(SCV) and a bypass were selected as design parameters for enhancing the swirl flow. The optimal intake port shape was also chosen as a parameter needed to efficiently generate a high swirl ratio. The results revealed that a key factor in generating a high swirl ratio was to control the intake airflow direction passing through the intake valve seat. Further, the swirl intensity was influenced by changing the distance between the helical and tangential ports, and the swirl flow was changed by the presence of a bypass near the intake valve seat. Additionally, the effect of intake port geometry on the in-cylinder flow field was investigated by using a laser sheet visualization method. The experimental results showed a correlation of swirl ratio and mass flow rate. In addition, we found that employing the bypass was an effective method to increase swirl ratio without sacrificing mass flow rate.

Constructal optimization for H-shaped multi-scale heat exchanger based on entransy theory

Analogizing with the definition of thermal efficiency of a heat exchanger,the entransy dissipation efficiency of a heat exchanger is defined as the ratio of dimensionless entransy dissipation rate to dimensionless pumping power of the heat exchanger.For the constraints of the total tube volume and total tube surface area of the heat exchanger,the constructal optimization of an H-shaped multi-scale heat exchanger is carried out by taking entransy dissipation efficiency maximization as optimization objective,and the optimal construct of the H-shaped multi-scale heat exchanger with maximum entransy dissipation efficiency is obtained.The results show that for the specified total tube volume of the heat exchanger,the optimal constructs of the first order T-shaped heat exchanger based on the maximizations of the thermal efficiency and entransy dissipation efficiency are obviously different with the lower mass flow rates of the cold and hot fluids.For the H-shaped multi-scale heat exchanger,the entransy dissipation efficiency decreases with the increase in mass flow rate when the heat exchanger order is fixed;for the specified dimensionless mass flow rate M(M<32.9),the entransy dissipation efficiency decreases with the increase in the heat exchanger order.The performance of the multi-scale heat exchanger is obviously improved compared with that of the single-scale heat exchanger.Moreover,the heat exchanger subjected to the total tube surface area constraint is also discussed in the paper.The optimization results obtained in this paper can provide a great compromise between the heat transfer and flow performances of the heat exchanger,provide some guidelines for the optimal designs of heat exchangers,and also enrich the connotation of entransy theory.

Non-axisymmetric Flow Characteristics in Centrifugal Compressor

The flow field distribution in centrifugal compressor is significantly affected by the non-axisymmetric geometry structure of the volute.The experimental and numerical simulation methods were adopted in this work to study the compressor flow field distribution with different flow conditions.The results show that the pressure distribution in volute is characterized by the circumferential non-uniform phenomenon and the pressure fluctuation on the high static pressure zone propagates reversely to upstream,which results in the non-axisymmetric flow inside the compressor.The non-uniform level of pressure distribution in large flow condition is higher than that in small flow condition,its effect on the upstream flow field is also stronger.Additionally,the non-uniform circumferential pressure distribution in volute brings the non-axisymmetric flow at impeller outlet.In different flow conditions,the circumferential variation of the absolute flow angle at impeller outlet is also different.Meanwhile,the non-axisymmetric flow characteristics in internal impeller can be also reflected by the distribution of the mass flow.The high static pressure region of the volute corresponds to the decrease of mass flow in upstream blade channel,while the low static pressure zone of the volute corresponds to the increase of the mass flow.In small flow condition,the mass flow difference in the blade channel is bigger than that in the large flow condition.

Advance in research of several types of streaming of pulse tube refrigerators

The pulse tube refrigerator （PTR） is a promising small-scale cryocooler. This paper first briefly introduces the history of the pulse tube refrigerator. It has pointed out that technology improvements and theoretical developments of the pulse tube refrig- erator closely relate with the internal streaming effects. Then the discovering history and classification of the streaming or DC （direct current） flow effect are summarized. It proposes for the first time that the physical significance of the streaming con- tains the driving mechanisms and the transport mechanisms. It demonstrates that the driving mechanisms are the asymmetry of fluid flow and temperature while the transport mechanisms are a loop or vorticity, which transmits nonlinear dissipations. The important advancements have been made over the past two decades all over the world in research of streaming of the pulse tube refrigerator including Gedeon DC flow, Rayleigb streaming, the third type of DC flow and the regenerator circulation. With regard to Gedeon DC flow, theoretical and experimental analyses have been made and different suppression methods are summarized. In the aspect of Rayleigh streaming, it mainly focuses on the analytical solution of the second-order mass flow and the research of tapered pulse tubes. In particular, limited research on the third type of DC flow and regenerator circulation is presented. The experimental measurement techniques of streaming also are summarized. Finally, this paper briefly discusses the key scientific and technical issues of the current research, and foretells the future development trends of streaming research in PTR.

Experimental Investigation of Boiling Two-phase Flow Instability of Nitrogen in a Vertical Tube

Boiling flow instability of nitrogen in a vertical tube is experimentally investigated in the present study. The experiments reveal that pressure has a significant effect on the characteristics of the heat flux-mass flux type boiling flow instability.First.the pressure has strong effects on both the developing time and the fluctuation amplitude.Especially increasing pressure leads to decrease the fluctuating amplitude of mass flux.Then,the mass flux evolving curves under different pressures feature out a shape like a leaf.The characteristics of the heat flux-mass flux type boiling flow instability under lower pressure are very complicated,however,with increasing pressure,this type of instability is gradually suppressed.

The Effect of Diffuser Angle on the Discharge Coefficient of a Miniature Critical Nozzle

Many researches on critical nozzles have been performed to accurately measure the mass flow rate of gas flow,and to standardize the performance as a flow meter.Recently,much interest is being paid on the measurement of very small mass flow rate in industry fields such as MEMS applications.However,the design and performance data of the critical nozzles obtained so far have been applied mainly to the critical nozzles with comparatively large diameters,and the works available on miniature critical nozzles are lacking.In the present study,a computational fluid dynamics method has been applied to investigate the influence of the diffuser angle on discharge coefficient of the miniature critical nozzles.In computations,the throat diameter of critical nozzle is varied from 0.2 mm to 5.0 mm and the diffuser angle is changed from 2 deg to 8 deg.The computational results are validated with some experimental data available.The results show that the present computational results predict appropriately the discharge coefficient of the gas flows through miniature critical nozzles.It is known that the discharge coefficient is considerably influenced by the diffuser angle,as the throat diameter of nozzle becomes small below a certain value.This implies that the miniature critical nozzles should be carefully designed.

Effects of bleed hole size on supersonic boundary layer bleed mass flow rate

The bleed hole diameter,depth,and boundary layer thickness are key design parameters of a supersonic bleed system.The evolution trend of single-hole bleed flow coefficient with the ratio of boundary layer thickness to bleed hole diameter and the ratio of bleed hole depth to diameter is investigated by numerical simulations under choking and non-choking conditions.The results show that the subsonic leading edge of the circular hole and the subsonic part of the boundary layer are the main factors causing lateral flow of the bleed hole.The effect of diameter on bleed mass flow rate is due to the viscous effect which reduces the effective diameter.The larger the ratio of displacement thickness to bleed hole diameter,the more obvious the viscous effect is.The depth affects bleed flow rate by changing the opening and closing states of the separation zone.When a certain depth is reached,the development of the boundary layer reduces the effective captured stream tube and thus reduces the bleed mass flow rate.The main objective of the study is to obtain the physical mechanism of the bleed hole size parameters affecting the bleed mass flow rate,and to provide theoretical guidance for the selection of the size of bleed holes in the design of a porous arrays bleed system in hypersonic inlets.

Visualization on Flow Patterns during Condensation of R410A in a Vertical Rectangular Channel

The visualization experiments on HFC R410A condensation in a vertical rectangular channel （14.34mm hydraulic diameter, 160mm length） were investigated. The flow patterns and heat transfer coefficients of condensation in the inlet region were presented in this paper. Better heat transfer performance can be obtained in the inlet region, and flow regime transition in other regions of the channel was also observed. Condensation experiments were carried out at different mass fluxes （ from 1.6 kg/h to 5.2 kg/h） and at saturation temperature 28~ C. It was found that the flow patterns were mainly dominated by gravity at low mass fluxes. The effects of interfacial shear stress on condensate fluctuation are significant for the film condensation at higher mass flux in vertical flow, and con- sequently, the condensation heat transfer coefficient increases with the mass flux in the experimental conditions, The drop formation and growth process of condensation were also observed at considerably low refrigerant vapor flow rate.

Natural Convective Heat and Mass Transfer on a Vertical Heated Plate for Water Flow Containing Metal Corrosion Particles

Corrosion products of structural materials when contained in water usually are in two states:soluble state and colloidal particles with diameter about 10^(-3)—10^(-1)μm.Deposits of such corrosion products on tube surfaces under high pressure will jeopardize the operating economy of power plant equipment and even result in accidents. A numerical study is reported in this paper of the natural convective heat and mass transfer on a vertical heated plate subject to the first or mixed kind of boundary conditions for high-pressure water(P=17MPa)containing metal corrosion products with consideration of variable thermophysical properties.

On the atmospheric movement and the imbalance of observed and calculated energy in the surface layer

Based on existing researches,here we theoretically summarized the characteristics of the atmospheric movement and turbulent transport of energy and substance in the surface layer as well as the ideal and the actual models for the turbulent transport.Then,using the data observed with eddy covariance at the semiarid climate and environment monitoring station(SACOL) in Lanzhou University from May to October during four consecutive years(September 2006-August 2010),we conducted a detailed analysis of the turbulent transport in the surface layer,through introducing the relative vertical turbulence intensity to characterize the turbulence strength,RIw=wn(wn+U),and also by adopting the method for controlling data quality at different levels.Our conclusions are:(1) The turbulent transport of energy and substance in the surface layer must obey the law of conservation of energy and the law of conservation of matter,the observed and calculated energy in the surface layer must be balanced,or closed in theory,but the actual observed and calculated energy just approximates the ideal in some degree and is difficult to achieve the energy balance.(2) The energy closure rate depends much on the atmospheric state in the surface layer,and the energy closure rate increases generally with the relative vertical turbulence intensity.(3) By the way of controlling data quality at different levels,it is found that the degree of data quality control can affect the closure rate,but it does not change the fact that the energy closure rate depends on the atmospheric state.(4) The calculation method of surface soil heat flux can affect energy closure rate,but does not change its dependence on the atmospheric state.

Numerical studies of the effects of phase transitions on Venusian mantle convection

This paper presents a study on the effects of phase transitions on the mantle convection of Venus in a three-dimensional （3D） spherical shell domain. Our model includes strong depth- and temperature-dependent viscosity and exothermic phase change from olivine to spinel as well as endothermic phase change from spinel to perovskite. From extensive numerical simulations of the effects of Rayleigh number （Ra）, and the Clapeyron slopes and depths of phase changes, we found the following： （1） The endothermic phase change prevents mass flow through the interface. Increasing the absolute value of the Clapeyron slopes decreases radial mass flux and normalized radial mass flux at the endotbermic phase boundary, and decreases the number of mantle plumes. In other words, mass flow through the phase boundary decreases. The inhibition influence of phase changes increases, as do convective wavelengths. （2） Increasing Ra also increases the convective wavelength and decreases the number of mantle plumes, but it has less influence on the mass exchange. As Ra increases, the convective vigor increases along with the radial mass flux and the mass flow through the phase boundary; however, the normalized mass flux through the phase boundary varies little with Ra, which is different from the conclusion that increasing Ra will greatly increase the inhibition of mass flow through the phase boundary based on two-dimensional （2D） modeling. （3） Increasing the depth of endothermic phase change will slightly decrease the number of mantle plumes, but has little effect on the mass flow through the phase boundary. Consistent with previous studies, our results show that the phase change from spinel to perovskite could inhibit the mass flow through the phase boundary, but they also show that the buildup of hot materials under the endothermic phase boundary in the 3D model could not be so large as to cause strong episodic overturns of mantle materials, which is quite different from previous 2D studies. Our results suggest that it is difficult for phase changes to cause significant magmatism on Venus; in other words, phase changes may not be the primary cause of catastrophic resurfacing on Venus.