提升矿山测量工作效率技术途径

为了进一步提高矿山测量工作效率,降低测量误差,避免测量事故发生,长春兴煤矿通过技术研究,对当前矿山测量工作主要作用进行分析,以及矿山测量技术进行分类,同时对提升矿山测量工作效率提出了若干项技术途径,确保矿山测量工作顺利开展,保证煤矿安全高效生产。

多天线频谱共享CR-NOMA系统安全中断性能分析

认知无线电(CR)非正交多址接入(NOMA)网络(记为CR-NOMA)已是无线通信领域的研究热点之一。由于无线信道的开放性,使得无线网络的安全通信成为当前急需解决的问题。该文研究了频谱共享多天线CR-NOMA网络安全中断性能,首先分析了最优天线选择(OAS)方案的安全中断概率(SOP),并推导了其精确的闭合表达式。其次,分析了空时传输(STT)方案的SOP,并推导了其精确的闭合表达式。最后,对次用户两种方案的SOP渐近性能进行了分析,揭示了系统参数对SOP的影响。最后,采用Monte Carlo仿真验证了理论分析的正确性。研究发现,两种方案基站分别存在一个最优峰值发射功率,使得远距离次用户的安全中断性能最佳。仿真结果表明增大基站峰值发射功率,OAS方案的近距离次用户的SOP会始终优于STT方案,远距离次用户的SOP会劣于STT方案。

河北CORS和EGM2008模型在RTK三维水深测量中的应用

将河北CORS和EGM2008重力场模型应用在RTK三维水深测量工作中,不受控制点个数和位置分布限制,无需求取七参数,可直接获取2000国家大地坐标系平面定位成果。另外,利用EGM2008模型计算出测区内少数点的高程异常后,可通过二次多项式曲面模型进行高程拟合,求出全部测点高程异常,最终得到正常高。通过在渤海湾某水深测量项目中的验证,结果表明该方法简单可行,其精度可达到规范要求。

RTK确定高程的方法及其应用

简要的阐述了RTK的工作原理,研究了RTK确定高程的统一模式,并对其应用作了比较深入的探讨。

Application of Prediction Techniques in Carbonate Karst Reservoir in Tarim Basin

Carbonate karst reservoir is the emphases of Tarim＇s carbonate exploration. However, it is buried at a large depth, which results in Weak seismic reflection signal and low S/N ratio. In addition, the karst reservoir contains great heterogeneity, so reservoir prediction is very difficult. Through many years of research and exploration, we have established a suite of comprehensive evaluation technology for carbonate karst reservoir using geophysical characteristics and a geological concept model, including a technique for reconstructing the paleogeomorphology of buried hills based on a sequence framework, seismic description of the karst reservoir, and strain variant analysis for fracture estimation. The evaluation technology has been successfully applied in the Tabei and Tazhong areas, and commercial production of oil and gas has been achieved. We show the application of this technology in the Lunguxi area in North Tarim in this paper.

Measuring-Basis Encrypted Quantum Key Distribution with Four-State Systems

A measuring-basis encrypted quantum key distribution scheme is proposed by using twelve nonorthogohal states in a four-state system and the measuring-basis encryption technique. In this scheme, two bits of classical information can be encoded on one four-state particle and the transmitted particles can be fully used.

Orthogonality of inductosyn angle-measuring system error and error-separating technology

Round inductosyn is widely used in inertial navigation test equipment, and its accuracy has significant effect on the general accuracy of the equipment. Four main errors of round inductosyn,i.e. the first-order long-period (360°) harmonic error, the second-order long-period harmonic error, the first-order short-period harmonic error and the second-order short-period harmonic error, are described, and the orthogonality of these four kinds of errors is studied. An error separating technology is proposed to separate these four kinds of errors, and in the process of separating the short-period harmonic errors, the arrangement in the order of decimal part of the angle pitch number can be omitted. The effectiveness of the technology proposed is proved through measuring and adjusting the angular errors.

Damage detection of frames using the increment of lateral displacement change

The method proposed in this paper is based on the fact that the damage in different types of structural members has distinctive influence on the structural stiffness. The intrinsic mechanical property of the structure is tapped and fully utilized for damage detection. The simplified model of the flexibility of frames treats the individual storeys as springs in series and the frame as an equivalent column. It fully considers the main deformation of all beams and columns in the frame. The deformation property of the simplified model accorded well with that of the actual frame model. The obtained increment of lateral displacement change (IOLDC) at the storey level was found to be very sensitive to the local damage in the frame. A damage detection method is pro- posed using the IOLDCs as the damage identification parameters. Numerical examples demonstrate the potential applicability of this method.

Correspondence of bubble size and frother partitioning in flotation

The size of bubbles created in the flotation process is of great importance to the efficiency of the mineral separation achieved.Meanwhile,it is believed that frother transport between phases is perhaps the most important reason for the interactive nature of the phenomena occurring in the bulk and froth phases in flotation,as frother adsorbed in the surface of rising bubbles is removed from the bulk phase and then released into the froth as a fraction of the bubbles burst.This causes the increased concentration in the froth compared to the bulk concentration,named as frother partitioning.Partitioning reflects the adsorption of frother on bubbles and how to influence bubble size is not known.There currently exists no such a topic aiming to link these two key parameters.To fill this vacancy,the correspondence between bubble size and frother partitioning was examined.Bubble size was measured by sampling-for-imaging(SFI)technique.Using total organic carbon(TOC)analysis to measure the frother partitioning between froth and bulk phases was determined.Measurements have shown,with no exceptions including four different frothers,higher frother concentration is in the bulk than in the froth.The results also show strong partitioning giving an increase in bubble size which implies there is a compelling relationship between these two,represented by CFroth/CBulk and D32.The CFroth/CBulkand D32 curves show similar exponential decay relationships as a function of added frother in the system,strongly suggesting that the frother concentration gradient between the bulk solution and the bubble interface is the driving force contributing to bubble size reduction.

Exploring the Sample Quality Using Rough Sets Theory for the Supervised Classification of Remotely Sensed Imagery

In the supervised classification process of remotely sensed imagery, the quantity of samples is one of the important factors affecting the accuracy of the image classification as well as the keys used to evaluate the image classification. In general, the samples are acquired on the basis of prior knowledge, experience and higher resolution images. With the same size of samples and the same sampling model, several sets of training sample data can be obtained. In such sets, which set reflects perfect spectral characteristics and ensure the accuracy of the classification can be known only after the accuracy of the classification has been assessed. So, before classification, it would be a meaningful research to measure and assess the quality of samples for guiding and optimizing the consequent classification process. Then, based on the rough set, a new measuring index for the sample quality is proposed. The experiment data is the Landsat TM imagery of the Chinese Yellow River Delta on August 8th, 1999. The experiment compares the Bhattacharrya distance matrices and purity index zl and △x based on rough set theory of 5 sample data and also analyzes its effect on sample quality.

ANALYSIS AND MEASUREMENT OF LARGE DYNAMIC RANGE RF SWITCH INTER-MODULATION

Radio Frequency (RF) switch circuit is the basic part of microwave devices and systems. The non-linearity distortion figure is necessary in the field of large dynamic range of signal. This letter analyzes the basic switch circuit and its inter-modulation, and studies in detail the measurement methods and systems of RF switch intercept point. It has provided cascaded simulation testing methods, which can accurately measure the PF switch, of which the second or third order intercept point value is above 75dB and 60dB, respectively. As the testing results are consistent with the theoretical analyses, it proves that the validity of the method satisfies the requirements of large scaled linearity measurement in engineering.

Settlement prediction and behaviour of pile foundations in deep clayey soil deposits

A new measurement technique is used to determine the settlement of bridge pile foundation and the thickness of deep compressed soft layer. The finite element Plaxis 3D foundation program is used in the analysis with a proposed empirical equation to modify the input parameters represented by the soil compression modulus. The results of the numerical analysis using the proposed empirical equation provide insight to the settlement analysis of pile groups in soft clayey soils; consequently, the finite element Plaxis 3D program can be a useful tool for numerical analysis. The numerical analysis is modified by adjusting the calculation of compression modulus from those obtained under pressure between 100-200 kPa by which the results of the settlement are modified and thus matching the realistic measurements. The absolute error is 3 mm which is accepted compared with the last researches. This scenario can be applied for the similar problems in the theoretical applications of deep foundations.

Characterization of Specific Spoilage Bacteria and Volatile Flavor Compounds of Flavored Crayfish

It is a common issue in the processing industry of crayfish that flavored crayfish stored at room temperature is perishable.In order to establish an effective putrid prediction mechanism,high-throughput sequencing and solid phase microextraction gas chromatography-mass spectrometry(SPME-GCMS)were used to analyse the microbial community structure and volatile flavor compounds of normal and putrid crayfish.The results showed that Aeromonas(57%),Macrococcus(7.7%),Vibrio sp.(6.6%),Acinetobacter(5%),Citrobacter(4.9%)and Enterobacter(1.49%)were the main bacterial genus in the refrigerated fresh crayfish(HNA).And Staphylococcus(17.04%),Aeromonas(4.46%),Xanthomonas(4.16%),Streptococcus(4.62%)and Enterococcus(2.77%)were the main bacterial genus in the marinated and refrigerated crayfish(HND).With the spoilage of samples(HNE and HNC),the diversity of bacteria decreased,and the specific spoilage bacteria grew rapidly,mainly Enterococcus,Bacillus,Lactobacillus,Leuconostoc,Weissella.Meanwhile,the volatile compounds in non-spoilage sample(HNA and HND)were mainly alkane compounds,aldehydes compound and esters compounds;and the volatile compounds in spoilage samples were mainly alcohols,acids,benzene compounds,terpenoids,N-containing compounds,S-containing compounds and ethers.This indicated that the contents and types of volatile compounds changed with the sample spoilage and deterioration.Correlation analysis results showed that Enterococcus,Lactobacillus and Bacillus were significantly positively correlated with alcohols,acids,benzene,terpenoids,N-containing compounds,S-containing compounds and ether compounds,while Aeromonas,Megasphaera,Acinetobacter,Citrobacter and Vibrio were significantly positively correlated with alkane compounds and esters compounds,and Leuconostoc were significantly positively correlated with alcohol compounds.These results can provide a theoretical guidance for the storage of cooked flavor crayfish at room temperature.

High Accuracy On-line Measurement Method of Motion Error on Machine Tools Straight-going Parts

Harmonic suppression, non-periodic and non-closing in straightness profile error that will bring about harmonic component distortion in measurement result are analyzed. The countermeasure-a novel accurate two-probe method in time domain is put forward to measure straight-going component motion error in machine tools based on the frequency domain 3-point method after symmetrical continuation of probes' primitive signal. Both straight-going component motion error in machine tools and the profile error in workpiece that is manufactured on this machine can be measured at the same time. The information is available to diagnose the fault origin of machine tools. The analysis result is proved to be correct by the experiment.

Food Physics and Food Safety- Some Aspects in Food Processing and Food Quality Control

The article deals with special questions of some aspects of food safety and application of methods of food physics in food processing and also in food quality control and quality assurance. The role of food safety has developed significantly in the last 2 decades, so today the production and processing of safe and quality food is of primary importance. Modem food production is based on principles of GAP and GMP （including GHP） and different methods and tools for quality control and assurance （IFS, HACCP, ISO-9000, ISO-9000/2010, ISO-22000, TQM）. There are different techniques and methods to produce safe food and to control the quality of the foodstuffs. The modem, up-to-date technologies and measurement techniques involve the application of many physical methods - high pressure, pulsing electrical field, microwave, non-destructive techniques （e.g., INAA, NMR, NIR-NIT, PAS）, radiation treatments as well. Using radiation technologies （of course not only nuclear ones） it is possible to fulfil some very important expectations of modem food processing, e.g., decrease of microbial contamination, improvement of sensory properties, increase of storability of food products.

BaF_2 TIME DIFFERENTIAL PERTURBED ANGULAR DISTRIBUTION SPECTROMETER

A BaF2 time differential perturbed angular distribution spectrometer has been established at the HI-13 tandem accelerator in CIAE. The time resolution of the spectrometer is 195 ps and the nonlinearity is less than 2 %. The spectrometer works very stably and no time drift is found over a period of experimelltal ruffs. This spectrometer has been successfully used in the g-factor measurement of 43 Sc (19/2-,3.1232 MeV).

Analysis of the development of Surveying and mapping technology in coal mine production research and Application

Coral measure is a very important link in the process of mine development and production .The measurement provide basis for mine development and production. The accuracy of the measurement will directly affect the safety of coal production. The essay will elaborates the significance of coral measure and tells some new teclmology used for coral measure, and put forward to the ways of some common measurement problems. Finally, it discusses on how to improve the quality of coal measure.

Ultrasonic Resonator Techniques for Broad-band Spectroscopy and for High-resolution Sound Velocity Measurement of Liquids

This review gives a short introduction into the principles of ultrasonic measurement techniques for liquids, using cavity resonators. Guidelines for the resonator design in broad-band ultrasonic stxctroscopy as well as in high-resolution single-frequncy or narrowband applications are presented. Deviations of the field configuration in real cells frtxn that in an ideal resonator are discussed and relations for the mode spectrum of cavity fields are given. Recent resonator measurement procedures and methods of data evaluation are mentioned briefly. Some examples of measurements show the extended usability of ultrasonic resonator techniques in basic science and in a wide range of applications for rrkaterials characterization, in manufacturing processes, as well as in control routines.

Measurement Techniques for Distribution Line Impedance by Minimum Pulse Injection

With a live wire, line impedance could be measured by means of only passive elements such as inductors or resistors, whose techniques are well known. However, as the voltage and current used for the measurement are increased, the size of the inductor or resistor being used also needs to be increased, so it would be virtually impossible to make an accurate measurement. Because of this, the authors have developed a novel measurement method for line impedance using LC resonance, which the authors describe first place. In the second place, the authors propose another line impedance. The novel method is that the rectangular wave with minimum voltage is injected into the distribution line system. By means of this method, the line capacitance and the line inductance can be measured. These proposals are confirmed by the simulation or experiment. Finally, the frequency response analysis method is to be examined, whose mechanism and results are to be presented and discussed.

Experimental investigation of the generation of large-amplitude internal solitary wave and its interaction with a submerged slender body

A principle of generating the nonlinear large-amplitude internal wave in a stratified fluid tank with large cross-section is pro- posed according to the ＇jalousie＇ control mode. A new wave-maker based on the principle was manufactured and the experi- ments on the generation and evolution of internal solitary wave were conducted. Both the validity of the new device and ap- plicability range of the KdV-type internal soliton theory were tested. Furthermore, a measurement technique of hydrodynamic load of internal waves was developed. By means of accurately measuring slight variations of internal wave forces exerted on a slender body in the tank, their interaction characteristics were determined. It is shown that through establishing the similarity between the model scale in the stratified fluid tank and the full scale in the numerical simulation the obtained measurement re- suits of internal wave forces are confirmed to be correct.