In order to obtain the distribution rules of in situ stress and mining-induced stress of Beiminghe Iron Mine, the stress relief method by overcoring was used to measure the in situ stress, and the MC type bore-hole st...In order to obtain the distribution rules of in situ stress and mining-induced stress of Beiminghe Iron Mine, the stress relief method by overcoring was used to measure the in situ stress, and the MC type bore-hole stress gauge was adopted to measure the mining-induced stress. In the in situ stress measuring, the technique of improved hollow inclusion cells was adopted, which can realize complete temperature compensation. Based on the measuring results, the distribution model of in situ stress was established and analyzed. The in situ stress measuring result shows that the maximum horizontal stress is 1.75-2.45 times of vertical stress and almost 1.83 times of the minimum horizontal stress in this mineral field. And the mining-induced stress measuring result shows that, according to the magnitude of front abutment pressure the stress region can be separated into stress-relaxed area, stress- concentrated area and initial stress area. At the -50 m mining level of this mine, the range of stress-relaxed area is 0-3 m before mining face; the range of stress-concentrated area is 3-55 m before mining face, and the maximum mining-induced stress is 16.5-17.5 MPa, which is 15-20 m from the mining face. The coefficient of stress concentration is 1.85.展开更多
According to the working environment of the polar glacier core drilling, a separatory funnel capillary viscometer which can be used for testing the viscosity of liquids under ultra-low temperature conditions was de- s...According to the working environment of the polar glacier core drilling, a separatory funnel capillary viscometer which can be used for testing the viscosity of liquids under ultra-low temperature conditions was de- signed. This viscometer has a simple structure and it is easy to operate, which can meet the testing requirements of different temperature conditions. The viscosity of the dimethyl silicone oil KF-96L-2.0cs was measured under different temperatures using this designed viseometer, and it is found that the viscometer coefficient K changes linearly with temperature. This testing method has relatively high test accuracy and its relative error is less than 4%, which can be used to test the viscosity of the different liquids in ultra-low temperature conditions.展开更多
This paper mainly described five kinds of common detection methods, including the test block method, core drilling method, rebound method, dialing out method and ultrasonic testing method and systematically analyzed t...This paper mainly described five kinds of common detection methods, including the test block method, core drilling method, rebound method, dialing out method and ultrasonic testing method and systematically analyzed the mechanism of all kinds of concrete strength detection methods as well as their advantages and disadvantages, which would provide a guide for construction personnel and research institutions to choose an economical ,accurate and safe detection method.展开更多
This paper investigates the effect of the location of testing area in residual stress measurement by Moiréinterferometry combined with hole-drilling method.The selection of the location of the testing area is ana...This paper investigates the effect of the location of testing area in residual stress measurement by Moiréinterferometry combined with hole-drilling method.The selection of the location of the testing area is analyzed from theory and experiment.In the theoretical study,the factors which affect the surface released radial strainεr were analyzed on the basis of the formulae of the hole-drilling method,and the relations between those factors andεr were established.By combining Moiréinterferometry with the hole-drilling method,the residual stress of interference-fit specimen was measured to verify the theoretical analysis.According to the analysis results,the testing area for minimizing the error of strain measurement is determined.Moreover,if the orientation of the maximum principal stress is known,the value of strain will be measured with higher precision by the Moiréinterferometry method.展开更多
In order to reduce the noises affixed to the signals when testing high frequency devices,a single-port test mode(S11) is used to test frequency response of high frequency(GHz) and dual-port surface acoustic wave devic...In order to reduce the noises affixed to the signals when testing high frequency devices,a single-port test mode(S11) is used to test frequency response of high frequency(GHz) and dual-port surface acoustic wave devices(SAWDs) in this paper.The feasibility of the test is proved by simulating the Fabry-perot model.The frequency response of the high-frequency dual-port resonant-type diamond SAWD is measured by S11 and the dual-port test mode(S21),respectively.The results show that the quality factor of the device is 51.29 and the 3 dB bandwidth is 27.8 MHz by S11-mode measurement,which is better than the S21 mode,and is consistent with the frequency response curve by simulation.展开更多
基金Projects(10702072, 10632100) supported by the National Nature Science Foundation of China
文摘In order to obtain the distribution rules of in situ stress and mining-induced stress of Beiminghe Iron Mine, the stress relief method by overcoring was used to measure the in situ stress, and the MC type bore-hole stress gauge was adopted to measure the mining-induced stress. In the in situ stress measuring, the technique of improved hollow inclusion cells was adopted, which can realize complete temperature compensation. Based on the measuring results, the distribution model of in situ stress was established and analyzed. The in situ stress measuring result shows that the maximum horizontal stress is 1.75-2.45 times of vertical stress and almost 1.83 times of the minimum horizontal stress in this mineral field. And the mining-induced stress measuring result shows that, according to the magnitude of front abutment pressure the stress region can be separated into stress-relaxed area, stress- concentrated area and initial stress area. At the -50 m mining level of this mine, the range of stress-relaxed area is 0-3 m before mining face; the range of stress-concentrated area is 3-55 m before mining face, and the maximum mining-induced stress is 16.5-17.5 MPa, which is 15-20 m from the mining face. The coefficient of stress concentration is 1.85.
基金Supported Project of the Natural Science Foundations of China(No.41106158)
文摘According to the working environment of the polar glacier core drilling, a separatory funnel capillary viscometer which can be used for testing the viscosity of liquids under ultra-low temperature conditions was de- signed. This viscometer has a simple structure and it is easy to operate, which can meet the testing requirements of different temperature conditions. The viscosity of the dimethyl silicone oil KF-96L-2.0cs was measured under different temperatures using this designed viseometer, and it is found that the viscometer coefficient K changes linearly with temperature. This testing method has relatively high test accuracy and its relative error is less than 4%, which can be used to test the viscosity of the different liquids in ultra-low temperature conditions.
文摘This paper mainly described five kinds of common detection methods, including the test block method, core drilling method, rebound method, dialing out method and ultrasonic testing method and systematically analyzed the mechanism of all kinds of concrete strength detection methods as well as their advantages and disadvantages, which would provide a guide for construction personnel and research institutions to choose an economical ,accurate and safe detection method.
基金supported by the National Basic Research Program of China(Grant Nos.2010CB631005 and 2011CB606105)the National Natural Science Foundation of China(Grant Nos.11232008,91216301,11227801 and 11172151)Tsinghua University Initiative Scientific Research Program
文摘This paper investigates the effect of the location of testing area in residual stress measurement by Moiréinterferometry combined with hole-drilling method.The selection of the location of the testing area is analyzed from theory and experiment.In the theoretical study,the factors which affect the surface released radial strainεr were analyzed on the basis of the formulae of the hole-drilling method,and the relations between those factors andεr were established.By combining Moiréinterferometry with the hole-drilling method,the residual stress of interference-fit specimen was measured to verify the theoretical analysis.According to the analysis results,the testing area for minimizing the error of strain measurement is determined.Moreover,if the orientation of the maximum principal stress is known,the value of strain will be measured with higher precision by the Moiréinterferometry method.
基金supported by the National Natural Science Foundation of China (Nos.50972105 and 60806030)Tianjin Natural Science Foundation (Nos.09JCZDJC16500,08JCYBJC14600 and ZD200709)
文摘In order to reduce the noises affixed to the signals when testing high frequency devices,a single-port test mode(S11) is used to test frequency response of high frequency(GHz) and dual-port surface acoustic wave devices(SAWDs) in this paper.The feasibility of the test is proved by simulating the Fabry-perot model.The frequency response of the high-frequency dual-port resonant-type diamond SAWD is measured by S11 and the dual-port test mode(S21),respectively.The results show that the quality factor of the device is 51.29 and the 3 dB bandwidth is 27.8 MHz by S11-mode measurement,which is better than the S21 mode,and is consistent with the frequency response curve by simulation.
