柴油机涡轮增压器常见故障与排除

废气涡轮增压器是增压柴油机的重要部件之一,本文分析了增压器常见故障产生的原因,提出了故障排除的方法。

Development of Turbocharger for Improving Diesel Engine Matching Performance

The two development ways of turbocharger technology to solve the problem of matching performance with diesel were presented. The ways of waste valve gate turbocharger and variable geometry turbocharger can solve the problem of engine’s low speed torque and achieve lower smoke level. Especially for variable geometry turbocharger, it covers all conditions of engine. It can not only improve the low engine’s speed torque and keep the power performance at high engine speed, but also cover wide engine speed performance that keeps lower fuel consumption and exhaust gas temperature in full load and part load matching. The results of theory analysis and experiment research showed that it’s the ideal solution to solve the matching problem of diesel engines.

Influence of volute distortion on the performance of turbocharger centrifugal compressor with vane diffuser

As the geometry of the volute of turbocharger compressor is non-axisymmetric,it causes a distortion at the outlet of the diffuser and influences the upstream components.A distortion model in which a pressure distortion was applied as outlet boundary condition was established to simulate the distortion induced by the volute.It turned out to be sufficient to impose a circumferentially asymmetric pressure distribution at the outlet of the diffuser to replace the volute.Based on the distortion model which was verified,the influence of the amplitude of the distortion on the performance of centrifugal compressor was studied in detail.The results show that the distortion severely harms aerodynamic stability of the investigated compressor.The larger the amplitude of the distortion,the worse the performance of the compressor.The distortion induced by asymmetric volute propagates to upstream components and causes local flow separation at part of diffuser and impeller,and then causes the compressor surge.When the amplitude of the volute distortion is 10%,the stable flow range of the centrifugal compressor decreases to near zero.To authors’knowledge,the relationship between the compressor performance and distortion amplitude is first obtained quantitatively,which provides evidence to improve the performance of turbocharger compressor by decreasing the distortion induced by asymmetric volute.

A novel experimental method to evaluate the impact of volute's asymmetry on the performance of a high pressure ratio turbocharger compressor

All components of a turbocharger compressor are axisymmetric except for the spiral-shaped,gas-collecting overhung volute.In this paper,a novel experimental method to evaluate the impact of the volute's asymmetry on centrifugal compressor performance is proposed and applied to a high pressure-ratio turbocharger compressor.This method can isolate the impact of the volute's asymmetry on the compressor performance for the first time.Experiments prove the considerable impact of the volute's asymmetry on the compressor performance,especially the stability and efficiency.The impact of the volute's asymmetry on compressor stability correlates with rotational speed and thus with the pressure ratio,constricting the stable flow range by up to 47 percent and decreasing the maximum efficiency by 4.8 percent at the design speed.The results provide evidence to exploit the potential of intrinsic non-axisymmetric flow induced by asymmetric volute to improve the performance of turbocharger compressor with a high pressure ratio.

Experimental study on the effects of HP and LP EGR on thermal efficiency and emissions of a two-stage turbocharged diesel engine

An experimental study was performed to compare the effects of high-and low-pressure exhaust gas recirculation loops(HP and LP EGR loops)on thermal efficiency and emissions of a diesel engine.Tests were conducted on a 12-L six-cylinder turbocharged diesel engine under various operating conditions.We found that at a low speed of 1100 r/min,1 MPa BMEP,the LP EGR loop could achieve higher brake thermal efficiency and lower emissions than the HP EGR.This is because the lower enthalpy available at the turbine inlet of the HP EGR loop increased the fuel/oxygen equivalence ratio.For the HP EGR,the gross indicated thermal efficiency was reduced by 1%,but pumping losses were only reduced by 0.5%,compared to the LP EGR loop.At a higher speed of 1600 r/min,1 MPa BMEP,the HP EGR loop attained a higher brake thermal efficiency and lower emissions because of the relatively sufficient flow through the turbocharger.For the HP EGR loop,the gross indicated thermal efficiency was only reduced by 0.5%and pumping losses were reduced by 1.5%,compared to the LP EGR loop.Lower fuel consumption and a longer ignition delay made the distribution of fuel/oxygen equivalence ratio more homogeneous,leading to lower emissions.Our data also showed that at the high speed of 1600 r/min,0.55 MPa BMEP,the brake thermal efficiency of the HP EGR loop first increased,then decreased as the EGR rate increased.Therefore,under all conditions,a reasonable match of both EGR loops could achieve a good balance between fuel consumption and emissions of NOx and soot.

Investigation of a Centrifugal Compressor and Study of the Area Ratio and TIP Clearance Effects on Performance

In this research, the centrifugal compressor of a turbocharger is investigated experimentally and numerically. Performance characteristics of the compressor were obtained experimentally by measurements of rotor speed and flow parameters at the inlet and outlet of the compressor. Three dimensional flow field in the impeller and dif- fuser was analyzed numerically using a full Navier-Stokes program with SST turbulence model. The performance characteristics of the compressor were obtained numerically, which were then compared with the experimental results. The comparison shows good agreement. Furthermore, the effect of area ratio and tip clearance on the performance parameters and flow field was stud- ied numerically. The impeller area ratio was changed by cutting the impeller exit axial width from an initial value of 4.1 mm to a final value of 5.1 mm, resulting in an area ratio from 0.792 to 0.965. For the rotor with exit axial width of 4.6 mm, performance was investigated for tip clearance of 0.0, 0.5 and 1.0 mm. Results of this simula- tion at design point showed that the compressor pressure ratio peaked at an area ratio of 0.792 while the effi- ciency peaked at a higher value of area ratio of 0.878. Also the increment of the tip clearance from 0 to 1 mm resulted in 20 percent efficiency decrease.

Effect of a Curved Duct Upstream on Performance of Small Centrifugal Compressors for Automobile Turbochargers

Since the automobile turbochargers are installed in an engine compartment with limited space, the ducts upstream of the turbocharger compressor may be curved in a complex manner. In the present paper, the effect of a curved duct upstream on performance of small centrifugal compressors for automobile turbochargers is discussed. The computational fluid dynamics (CFD) analysis of a turbocharger compressor validated for the compressor model with the straight pipe applied to the compressor with the curved pipe are executed, and the deterioration of the performance for the curved pipe is confirmed. It is also found that the deterioration of compressor performance is caused by the interaction of the secondary flow and the impeller.

Effects of blade bowing on the performance of a high pressure-ratio turbocharger centrifugal compressor with self-recirculation casing treatment

The effects of blade bowing on the performance of a high pressure-ratio turbocharger centrifugal compressor were studied by experiments and numerical simulation.The results showed that the negative bowing was capable of increasing the choke mass rate and the efficiency but decreased the surge mass flow rate,while the positive bowing had the opposite effects.When coupling with the self-recirculation casing treatment,the surge mass flow rate of the compressor with negative bowing blade was almost identical with that of the prototype,while the choke mass flow rate was still larger,and the total effect contributed to an increase of the stable flow range by 5.85%at design speed.Besides,the flow mechanism of the coupling effects of blade bowing and self-recirculation casing treatment was discussed.

Effect of Double Air Injection on Performance Characteristics of Centrifugal Compressor

In the operation of a centrifugal compressor of turbocharger, instability phenomena such as rotating stall and surge are induced at a lower flow rate close to the maximum pressure ratio. In this study, for the suppression of surge phenomenon resulting in the extension of the stable operating range of centrifugal compressor to lower flow rate, the compressed air at the compressor exit was re-circulated and injected into the impeller inlet by using the double injection nozzle system. The experiments were performed to find out the optimum circumferential position of the second nozzle relative to the fixed first one and the optimum inner diameter of the injection nozzles, which are able to most effectively reduce the flow rate of surge inception. Moreover, in order to examine the universality of these optimum values, the experiments were carried out for two types of compressors.

Effects of Reynolds number on the performance of a high pressure-ratio turbocharger compressor

The effects of Reynolds number on the performance of a high pressure-ratio turbocharger compressor were investigated by both experiments and numerical simulation. The experimental results show that the pressure ratio and the efficiency of the compressor respectively decrease by 7.9% and 6.9% when Reynolds number drops from 9.86×10 5 to 2.96×10 5 . The numerical simulation predicts a similar trend as the experimental results although it underestimates the deterioration of the performance under low Reynolds number conditions. According to simulation results, the boundary layer thickness increases at the inducer, which decreases the throat area and leads to smaller choke mass flow rate. The increments of the boundary thickness are relatively small at the rear part of the impeller. The boundary layer separation flow is severe. The interaction between boundary layer separation flows and leakage flows causes the high loss region at the rear part of the impeller passage under low Reynolds number condition.