This paper proposes an analysis and a direct power control (DPC) design of a wind turbine driven doubly-fed induction generator (DFIG) under unbalanced network voltage conditions. A DFIG model described in the positiv...This paper proposes an analysis and a direct power control (DPC) design of a wind turbine driven doubly-fed induction generator (DFIG) under unbalanced network voltage conditions. A DFIG model described in the positive and negative synchronous reference frames is presented. Variations of the stator output active and reactive powers are fully deduced in the presence of negative sequence supply voltage and rotor flux. An enhanced DPC scheme is proposed to eliminate stator active power oscillation during network unbalance. The proposed control scheme removes rotor current regulators and the decomposition processing of positive and negative sequence rotor currents. Simulation results using PSCAD/EMTDC are presented on a 2-MW DFIG wind power generation system to validate the feasibility of the proposed control scheme under balanced and unbalanced network conditions.展开更多
The gassed power demand and volumetric mass transfer coefficient (kca) were investigated in a fully baffled, dished-base stirred vessel with a diameter of 0.30 m agitated by five triple-impeller combinations. Six ty...The gassed power demand and volumetric mass transfer coefficient (kca) were investigated in a fully baffled, dished-base stirred vessel with a diameter of 0.30 m agitated by five triple-impeller combinations. Six types of impellers (six-half-elliptical-blade disk turbine (HEDT), four-wide-blade hydrofoil impeller (WH) pumping down (D) and pumping up (U), parabolic-blade disk turbine (PDT), and CBY narrow blade (N) and wide blade (W)) were used to form five combinations identified by PDT + 2CBYN, PDT + 2CBYw, PDT + 2WHD, HEDT + 2WHD and HEDT + 2WHo, respectively. The results show that the relative power demand of HEDT + 2WHu is higher than that of other four impeller combinations under all operating conditions. At low superficial gas velocity (uc), kLa differences among impeller combinations are not obvious. However when UG iS high, PDT + 2WHD shows the best mass transfer performance and HEDT + 2WHu shows the worst mass trans- fer performance under all operating conditions. At high uc and a given power input, the impeller combinations with high agitation speed and big projection cross-sectional area lead to relatively high values of kLa. Based on the experimental data, the regressed correlations of gassed power number with Froude number and gas flow number, and kLa with power consumption and superficial gas velocity are obtained for five different impeller combinations, which could be used as guidance for industrial design.展开更多
This paper investigates the function of doubly-fed asynchronous machine(DASM)with emphasis placed on its ability to the stabilization of the power system including wind generators.P(active power)and Q(reactive power)c...This paper investigates the function of doubly-fed asynchronous machine(DASM)with emphasis placed on its ability to the stabilization of the power system including wind generators.P(active power)and Q(reactive power)compensation from DASM can be regulated independently through secondary-excitation controlling.Simulation results by power system computer aided design(PSCAD)show that DASM can restore the wind-generator system to a normal operating condition rapidly even following severe transmission-line failures.Comparison studies have also been performed between wind turbine pitch control and proposed method.展开更多
Wind energy is one of the most promising renewable energy sources, straight-bladed vertical axis wind turbine(S-VAWT) appears to be particularly promising for the shortage of fossil fuel reserves owing to its distinct...Wind energy is one of the most promising renewable energy sources, straight-bladed vertical axis wind turbine(S-VAWT) appears to be particularly promising for the shortage of fossil fuel reserves owing to its distinct advantages, but suffers from poor self-starting and low power coefficient. Variable-pitch method was recognized as an attractive solution to performance improvement, thus majority efforts had been devoted into blade pitch angle effect on aerodynamic performance. Taken into account the local flow field of S-VAWT, mathematical model was built to analyze the relationship between power outputs and pitch angle. Numerical simulations on static and dynamic performances of blade were carried out and optimized pitch angle along the rotor were presented. Comparative analyses of fixed pitch and variable-pitch S-VAWT were conducted, and a considerable improvement of the performance was obtained by the optimized blade pitch angle, in particular, a relative increase of the power coefficient by more than 19.3%. It is further demonstrated that the self-starting is greatly improved with the optimized blade pitch angle.展开更多
The use of diffusers around the horizontal-axis wind turbines has been widely studied since the diffuser improves the power coefficient of the turbine and it is often called DAWTs (diffuser augmented wind turbines)....The use of diffusers around the horizontal-axis wind turbines has been widely studied since the diffuser improves the power coefficient of the turbine and it is often called DAWTs (diffuser augmented wind turbines).Turbines using diffuser are called DWATs (Diffuser Augmented Turbines),and have efficiency bigger than the Betz limit (maximum energy flow extracted = 59.26%). Thus, this study presents a mathematical model describing the behavior of the velocity profile internally to a diffuser according to the characteristics of flow and geometry of a conical diffuser. The results are compared with experimental data and show good agreement.展开更多
In the early development of the wind energy, the majority of the wind turbines have been operated at constant speed. Subsequently, the number of variable-speed wind turbines installed in wind farms has increased. In t...In the early development of the wind energy, the majority of the wind turbines have been operated at constant speed. Subsequently, the number of variable-speed wind turbines installed in wind farms has increased. In this paper, a comparative performance of fixed and variable speed wind generators with Pitch angle control has been presented. The first is based on a squirrel cage Induction Generator (IG) of 315 kW rated power, connected directly to the grid. The second incorporated a Permanent Magnet Synchronous Generator (PMSG) of 750 kW rated power. The performances of each studied wind generator are evaluated by simulation works and variable speed operation is highlighted as preferred mode of operation.展开更多
In this work, the authors propose the study of a wind speed variable based on the DFAM (double fed asynchronous machine). The model of the turbine is drawn from the classical equations describing the operation of a ...In this work, the authors propose the study of a wind speed variable based on the DFAM (double fed asynchronous machine). The model of the turbine is drawn from the classical equations describing the operation of a variable wind speed. The torque generated by the turbine is applied to the DFAM directly connected on the network side and the stator via a bidirectional converter side rotor. This configuration allows velocity variations of ±30% around the synchronous speed and the converter is then sized to one third of the rated power of the machine. The DFAM is controlled by a control vector ensuring operation of the wind turbine power coefficient maximum.展开更多
In the present research work, the pitch-control is carried out such that the rotor blades are rotated around their longitudinal axis while the rotor continues its normal rotation. It is really a challenge to produce a...In the present research work, the pitch-control is carried out such that the rotor blades are rotated around their longitudinal axis while the rotor continues its normal rotation. It is really a challenge to produce a clever design to pitch the rotor blades by the optimal amount so as to maximize the power output at all wind speeds. The mechanism is implemented to a three-blade, horizontal-axis, home-scale wind turbine. The mechanism is powered by a suitable DC (direct-current) motor. The tests were carried out in the open section of a delivery wind tunnel. The air speed was measured by a suitable anemometer. The corresponding rotational speed (rpm) and output voltage at different wind speeds were measured and recorded for calibration of the control system. The mechanism proved to be successful in controlling the pitch angle over a wide range of wind speeds.展开更多
It is difficult for renewable energy resources to provide constant power with excellent quality for the grid system. This serial research proposes a power stabilization system with a pumped storage to guarantee power ...It is difficult for renewable energy resources to provide constant power with excellent quality for the grid system. This serial research proposes a power stabilization system with a pumped storage to guarantee power quality and capacity, while the outputs from the energy resources are at unstable and/or fluctuating conditions. The power stabilization system with a counter-rotating type pump-turbine unit was prepared and operated at the pumping and the turbine modes. The unit composed of the tandem impellers/runners connected to the inner and the outer armatures of the unique motor/generator. The experiments have verified that this type pump-turbine unit is reasonably effective to stabilize momentarily/instantaneously the fluctuating power from the renewable energy resources.展开更多
Optimization of airfoil characteristics such as lift and drag is essential for high efficiency wind turbine blade design. In this research, effects of airfoil lift and drag on blade power coefficients were investigate...Optimization of airfoil characteristics such as lift and drag is essential for high efficiency wind turbine blade design. In this research, effects of airfoil lift and drag on blade power coefficients were investigated by using of wind turbine blade design software, PROPID. Firstly, a wind turbine blade of 2MW class was designed with DU-serics airfoils in the inner part and with aNACA series airfoil as a main airfoil in the outer part. Lift distribution was set to have near L/D maximum at each span station. Then, lift and drag curves were modified to observe effect of L/D variation. Drag and lift change with constant L/D on blade power coefficient was also studied for sensitivity investigation. Each case was optimized with Newtonian iteration incorporated in PROPID. High design lift coefficient results in less chord length and twist angle to maintain same aerodynamic load level. And, power coefficient wasn't improved much with high L/D. During the process, optimal inputs such as lift distribution, design lift and induction factors were suggested. As results, it was found that L/D maximization was important to obtain high efficiency. For the L/D maximization, lift maximization was important to minimize structural weight, but decreasing drag didn't affect the blade shape.展开更多
This study aims to develop a water turbine suitable for ultra-low heads in open channels, with the end goal being the effective utilization of unutilized hydroelectric energy in agricultural water channels. We perform...This study aims to develop a water turbine suitable for ultra-low heads in open channels, with the end goal being the effective utilization of unutilized hydroelectric energy in agricultural water channels. We performed tests by applying a cross-flow runner to an open channel as an undershot water turbine while attempting to simplify the structure and eliminate the casing. We experimentally investigated the flow fields and performance of water tur- bines in states where the flow rate was constant for the undershot cross-flow water turbine mentioned above. In addition, we compared existing undershot water turbines with our undershot cross-flow water turbine after at- taching a bottom plate to the runner. From the results, we were able to clarify the following. Although the effec- tive head for cross-flow runners with no bottom plate was lower than those found in existing runners equipped with a bottom plate, the power output is greater in the high rotational speed range because of the high turbine ef- ficiency. Also, the runner with no bottom plate differed from rtmners that had a bottom plate in that no water was being wound up by the blades or retained between the blades, and the former received twice the flow due to the flow-through effect. As a result, the turbine efficiency was greater for runners with no bottom plate in the full ro- tational speed range compared with that found in runners that had a bottom plate.展开更多
基金Project (No. 50577056) supported by the National Natural Science Foundation of China
文摘This paper proposes an analysis and a direct power control (DPC) design of a wind turbine driven doubly-fed induction generator (DFIG) under unbalanced network voltage conditions. A DFIG model described in the positive and negative synchronous reference frames is presented. Variations of the stator output active and reactive powers are fully deduced in the presence of negative sequence supply voltage and rotor flux. An enhanced DPC scheme is proposed to eliminate stator active power oscillation during network unbalance. The proposed control scheme removes rotor current regulators and the decomposition processing of positive and negative sequence rotor currents. Simulation results using PSCAD/EMTDC are presented on a 2-MW DFIG wind power generation system to validate the feasibility of the proposed control scheme under balanced and unbalanced network conditions.
基金Supported by the National Natural Science Foundation of China(21206002,21376016)
文摘The gassed power demand and volumetric mass transfer coefficient (kca) were investigated in a fully baffled, dished-base stirred vessel with a diameter of 0.30 m agitated by five triple-impeller combinations. Six types of impellers (six-half-elliptical-blade disk turbine (HEDT), four-wide-blade hydrofoil impeller (WH) pumping down (D) and pumping up (U), parabolic-blade disk turbine (PDT), and CBY narrow blade (N) and wide blade (W)) were used to form five combinations identified by PDT + 2CBYN, PDT + 2CBYw, PDT + 2WHD, HEDT + 2WHD and HEDT + 2WHo, respectively. The results show that the relative power demand of HEDT + 2WHu is higher than that of other four impeller combinations under all operating conditions. At low superficial gas velocity (uc), kLa differences among impeller combinations are not obvious. However when UG iS high, PDT + 2WHD shows the best mass transfer performance and HEDT + 2WHu shows the worst mass trans- fer performance under all operating conditions. At high uc and a given power input, the impeller combinations with high agitation speed and big projection cross-sectional area lead to relatively high values of kLa. Based on the experimental data, the regressed correlations of gassed power number with Froude number and gas flow number, and kLa with power consumption and superficial gas velocity are obtained for five different impeller combinations, which could be used as guidance for industrial design.
文摘This paper investigates the function of doubly-fed asynchronous machine(DASM)with emphasis placed on its ability to the stabilization of the power system including wind generators.P(active power)and Q(reactive power)compensation from DASM can be regulated independently through secondary-excitation controlling.Simulation results by power system computer aided design(PSCAD)show that DASM can restore the wind-generator system to a normal operating condition rapidly even following severe transmission-line failures.Comparison studies have also been performed between wind turbine pitch control and proposed method.
基金Project(HEUCF110707)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(E201216)supported by Heilongjiang Natural Science Fund,China
文摘Wind energy is one of the most promising renewable energy sources, straight-bladed vertical axis wind turbine(S-VAWT) appears to be particularly promising for the shortage of fossil fuel reserves owing to its distinct advantages, but suffers from poor self-starting and low power coefficient. Variable-pitch method was recognized as an attractive solution to performance improvement, thus majority efforts had been devoted into blade pitch angle effect on aerodynamic performance. Taken into account the local flow field of S-VAWT, mathematical model was built to analyze the relationship between power outputs and pitch angle. Numerical simulations on static and dynamic performances of blade were carried out and optimized pitch angle along the rotor were presented. Comparative analyses of fixed pitch and variable-pitch S-VAWT were conducted, and a considerable improvement of the performance was obtained by the optimized blade pitch angle, in particular, a relative increase of the power coefficient by more than 19.3%. It is further demonstrated that the self-starting is greatly improved with the optimized blade pitch angle.
文摘The use of diffusers around the horizontal-axis wind turbines has been widely studied since the diffuser improves the power coefficient of the turbine and it is often called DAWTs (diffuser augmented wind turbines).Turbines using diffuser are called DWATs (Diffuser Augmented Turbines),and have efficiency bigger than the Betz limit (maximum energy flow extracted = 59.26%). Thus, this study presents a mathematical model describing the behavior of the velocity profile internally to a diffuser according to the characteristics of flow and geometry of a conical diffuser. The results are compared with experimental data and show good agreement.
文摘In the early development of the wind energy, the majority of the wind turbines have been operated at constant speed. Subsequently, the number of variable-speed wind turbines installed in wind farms has increased. In this paper, a comparative performance of fixed and variable speed wind generators with Pitch angle control has been presented. The first is based on a squirrel cage Induction Generator (IG) of 315 kW rated power, connected directly to the grid. The second incorporated a Permanent Magnet Synchronous Generator (PMSG) of 750 kW rated power. The performances of each studied wind generator are evaluated by simulation works and variable speed operation is highlighted as preferred mode of operation.
文摘In this work, the authors propose the study of a wind speed variable based on the DFAM (double fed asynchronous machine). The model of the turbine is drawn from the classical equations describing the operation of a variable wind speed. The torque generated by the turbine is applied to the DFAM directly connected on the network side and the stator via a bidirectional converter side rotor. This configuration allows velocity variations of ±30% around the synchronous speed and the converter is then sized to one third of the rated power of the machine. The DFAM is controlled by a control vector ensuring operation of the wind turbine power coefficient maximum.
文摘In the present research work, the pitch-control is carried out such that the rotor blades are rotated around their longitudinal axis while the rotor continues its normal rotation. It is really a challenge to produce a clever design to pitch the rotor blades by the optimal amount so as to maximize the power output at all wind speeds. The mechanism is implemented to a three-blade, horizontal-axis, home-scale wind turbine. The mechanism is powered by a suitable DC (direct-current) motor. The tests were carried out in the open section of a delivery wind tunnel. The air speed was measured by a suitable anemometer. The corresponding rotational speed (rpm) and output voltage at different wind speeds were measured and recorded for calibration of the control system. The mechanism proved to be successful in controlling the pitch angle over a wide range of wind speeds.
文摘It is difficult for renewable energy resources to provide constant power with excellent quality for the grid system. This serial research proposes a power stabilization system with a pumped storage to guarantee power quality and capacity, while the outputs from the energy resources are at unstable and/or fluctuating conditions. The power stabilization system with a counter-rotating type pump-turbine unit was prepared and operated at the pumping and the turbine modes. The unit composed of the tandem impellers/runners connected to the inner and the outer armatures of the unique motor/generator. The experiments have verified that this type pump-turbine unit is reasonably effective to stabilize momentarily/instantaneously the fluctuating power from the renewable energy resources.
文摘Optimization of airfoil characteristics such as lift and drag is essential for high efficiency wind turbine blade design. In this research, effects of airfoil lift and drag on blade power coefficients were investigated by using of wind turbine blade design software, PROPID. Firstly, a wind turbine blade of 2MW class was designed with DU-serics airfoils in the inner part and with aNACA series airfoil as a main airfoil in the outer part. Lift distribution was set to have near L/D maximum at each span station. Then, lift and drag curves were modified to observe effect of L/D variation. Drag and lift change with constant L/D on blade power coefficient was also studied for sensitivity investigation. Each case was optimized with Newtonian iteration incorporated in PROPID. High design lift coefficient results in less chord length and twist angle to maintain same aerodynamic load level. And, power coefficient wasn't improved much with high L/D. During the process, optimal inputs such as lift distribution, design lift and induction factors were suggested. As results, it was found that L/D maximization was important to obtain high efficiency. For the L/D maximization, lift maximization was important to minimize structural weight, but decreasing drag didn't affect the blade shape.
文摘This study aims to develop a water turbine suitable for ultra-low heads in open channels, with the end goal being the effective utilization of unutilized hydroelectric energy in agricultural water channels. We performed tests by applying a cross-flow runner to an open channel as an undershot water turbine while attempting to simplify the structure and eliminate the casing. We experimentally investigated the flow fields and performance of water tur- bines in states where the flow rate was constant for the undershot cross-flow water turbine mentioned above. In addition, we compared existing undershot water turbines with our undershot cross-flow water turbine after at- taching a bottom plate to the runner. From the results, we were able to clarify the following. Although the effec- tive head for cross-flow runners with no bottom plate was lower than those found in existing runners equipped with a bottom plate, the power output is greater in the high rotational speed range because of the high turbine ef- ficiency. Also, the runner with no bottom plate differed from rtmners that had a bottom plate in that no water was being wound up by the blades or retained between the blades, and the former received twice the flow due to the flow-through effect. As a result, the turbine efficiency was greater for runners with no bottom plate in the full ro- tational speed range compared with that found in runners that had a bottom plate.