液/固相单一离子吸附体系的动力学预测模型

对四种液/固相单一离子吸附体系的动力学研究结果表明:吸附速率不仅随时间变化,也与起始离子浓度(C_0)和吸附剂浓度(W_0)有关;Lagergren准二级方程在给定的起始离子浓度及吸附剂浓度下具有很高的模拟精确度,但其参数随起始离子浓度和吸附剂浓度的变化而变化,且无法确定其间的函数关系;结合四组分离子吸附模型,提出了新的动力学方程,实验结果表明,新方程具有较高的模拟精确度,其参数与C_0和W_0具有相对稳定的函数关系,可作为液/固相单一离子吸附体系中给定C_0,W_0条件下吸附动力学过程的预测模型.

Mechanism of Off-Bottom Suspension of Solid Particles in a Mechanical Stirred Tank

The minimum fluid velocity to maintain particles just suspendedwas deduced, and the theoretical analysis shows that the minimumvelocity is influenced by the properties of the solid and liquid, notby the operational conditions. For justification, the local minimumvelocity at the bottom of the tank was measured by a bi- electrodeconductivity probe, in a square-sectioned stirred tank (0.75m×0.75×1.0m) with the glass beads-water system. The experiments showed thatthe fluid velocities for the same suspension state were identicaldespite that the power Dissipated per unite mass was not the sameunder different configuration and operation. Both theoreticalanalysis And experimental results indicate that the off-bottomsuspension is controlled by the local fluid flow over the bottom Ofthe stirred tank.

Solid-Liquid Equilibria of trans-1,2-Cyclohexanediol＋Butyl Acetate＋ Water Ternary System

Using a laser observation technique,the solubilities of trans-1,2-cyclohexanediol in butyl acetate+wa- ter were measured at the temperature range from 298.15K to 323.15K by a synthetic method at atmospheric pres- sure.It is shown that the solubilities of trans-1,2-cyclohexanediol in butyl acetate+water were affected greatly by the proportion of butyl acetate and water,and presented maximum value at given temperature.The UNIFAC model was used to correlate the experimental data.The average relative deviation(ARD)between experimental and calculated values is 3.03%.

Simple Hydrostatic Model of Contact Angle Hysteresis of a Sessile Drop on Rough Surface

The phenomenon of hysteresis of contact angle is an important topic subject to a long time of argument.A simple hydrostatic model of sessile drops under the gravity in combination with an ideal surface roughness model is used to interpret the process of drop volume increase or decrease of a planar sessile drop and to shed light on the contact angle hysteresis and its relationship with the solid surface roughness. With this model, the advancing and receding contact angles are conceptually explained in terms of equilibrium contact angle and surface roughness only,without invoking the thermodynamic multiplicity. The model is found to be qualitatively consistent to experimental observations on contact angle hysteresis and it suggests a possible way to approach the hysteresis of three-dimensional sessile drops.

Gas–Liquid Mass Transfer Characteristics in a Gas–Liquid–Solid Bubble Column under Elevated Pressure and Temperature

abstract The volumetric mass transfer coefficient kLa of gases （H2, CO, CO2） and mass transfer coefficient kL on liquid par-affin side were studied using the dynamic absorption method in slurry bubble column reactors under elevated temperature and elevated pressure. Meanwhile, gas-holdup and gas-liquid interfacial area a were obtained. The effects of temperature, pressure, superficial gas velocity and solid concentration on the mass transfer coeffi-cient were discussed. Experimental results show that the gas-liquid volumetric mass transfer coefficient kLa and interfacial area a increased with the increase of pressure, temperature, and superficial gas velocity, and decreased with the slurry concentration. The mass transfer coefficient kL increased with increasing superficial gas velocity and temperature and decreased with higher slurry concentration, while it changed slightly with pressure. Ac-cording to analysis of experimental data, an empirical correlation is obtained to calculate the values of kLa for H2 （CO, CO2） in the gas-paraffin-quartz system in a bubble column under elevated temperature and elevated pressure.

Effect of Working Temperature on the Resistance Characteristic of a Pleated Stainless Steel Woven Filter

Effect of working temperature on the resistance characteristic including the permeability coefficient and the pressure drop evolution of a pleated stainless steel woven filter with a nominal pore size of 0.5 μm has been studied. The permeability coefficient was obtained based on the pressure drop data and the Darcy＇s law. In three filtration experiments, pure carbon dioxide at 283 K, nitrogen at 85 K and liquid helium at 18 K are adopted, respectively. It is found that the permeability coefficient decreases at the working temperature due to the cold shrink of the filter element at cryogenic temperature. Then, two kinds of feed slurries, mixture of liquid nitrogen and solid carbon dioxide at 85 K, and mixture of liquid helium and solid nitrogen at 18 K, flow into the filter cell. The solid particles are deposited on the filter surface to form a filter cake and the purified liquid flows through the filter. It is found that the pressure drop evolution shows the same trend on these two temperatures, which can be divided into three stages with high filtration efficiency, indicating the feasibility of the filter for cryogenic application. However, variant cake resistances are obtained, which is resulted from the different interactions between solid particles in the feed slurry at lower working temperature.

Tissue culture of three species of Laurencia complex

To establish a micropropagation system of three Laurencia complex species （Laurencia okamurai, Laurencia tristicha, and Chondrophvcus undulatus） by tissue culture techniques, we studied the regeneration characteristics and optimal culture conditions of axenic algal fragments cultured on solid medium and in liquid medium. Regeneration structures were observed and counted regularly under a reverse microscope to investigate the regeneration process, polarity and optimal illumination, and temperature and salinity levels. The results show that in most cultures of the three species, we obtained bud regeneration on solidified medium with 0.5% agar and in liquid medium. Rhizoid-like regeneration was filamentous and developed from the lower cut surface of fragments in L. okamurai, but was discoid and developed from the apical back side of bud regeneration in L. tristicha and C. undulatus. Regeneration polarity was localized to the apical part of algal fronds in all three species, and on fragments cut from the basal part of algae buds could develop from both the upper and the lower cut surfaces. Buds could develop from both the medullary and the cortical portions in L. okamurai and C. undulatus, while in L. tristicha, buds only emerged from the cortex. The optimal culture conditions for L. okamurai were 4 500 lx, 20℃ and 35 （salinity）; for C. undulatus, 4 500 lx, 20℃ and 30; and for L. tristicha, 4 500 lx, 25℃ and 30.