液力变矩器液力性能及试验研究

液力变矩器的液力性能对于自动变速器的匹配特别重要,最终会影响整个传动系统甚至整车的性能。所以如何去测量以及评价液力变矩器的液力性能是液力变矩器或变速箱开发的一个重要环节。本文简单描述了液力变矩器的液力性能的特性以及如何进行台架试验的,对从事相关工作的人员具有一定的指导意义。

基于计算流体力学的循环圆设计参数对液力变矩器的性能影响预测

为了提高改型设计效率,建立了液力变矩器参数化流道模型并进行三维流场仿真计算,与试验数据对比结果验证了参数化模型的可靠性。在此基础上,分别研究了相对截面积、扁平率、循环圆径向比和进出口半径等循环圆设计参数对液力变矩器性能的影响,并对比分析了各设计参数对液力性能的影响程度。结果表明,相对截面积对失速泵轮能容系数影响最大,但对失速变矩比和最大效率影响最小;扁平率、泵轮出口半径和导轮进出口半径对失速变矩比均有较大影响;而泵轮出口半径对最大效率影响最大。研究结果为液力变矩器的优化设计提供了理论参考。

扁平化液力变矩器循环圆设计及液力性能分析

研究扁平率变化对液力变矩器液力性能的影响。采用基于椭圆的新型设计方法,设计4种扁平率互不相同的液力变矩器。通过CFD对内流场进行仿真,分析其压力场和速度场的变化,与原型进行对比,得出扁平率对液力变矩器液力性能的影响规律。发现随着扁平率的降低,液力变矩器整体液力性能呈下降趋势。

液力变矩器耦合及倒拖工况仿真优化方法研究

着眼于液力变矩器在耦合工况之后乃至倒拖工况的仿真计算分析方法研究,以改变在液力变矩器传统的仿真计算中耦合点之后的液力性能计算并不能被很好呈现的缺点,通过CFD(computational fluid dynamics)及最小二乘拟合的方式加入了导轮在耦合工况内的影响,对液力变矩器企业开发过程有着现实意义.

WC-Ni_3Al-B composites prepared through Ni+Al elemental powder route

In order to develop the liquid phase sintering process of WC-Ni3Al-B composites,the preparation process of WC＋Ni3Al prealloyed powder by reaction synthesis of carbonyl Ni,analytical purity Al and coarse WC powders was investigated.DSC and XRD were adopted to study the procedure of phase transformation for the 3Ni＋Al and 70%WC＋（3Ni＋Al） mixed powders in temperature ranges of 550-1200 °C and 25-1400 °C,respectively.The results demonstrate that the formation mechanism of Ni3Al depends on the reaction temperature.Besides WC phase,there exist Ni2Al3,NiAl and Ni3Al intermetallics in the powder mixture after heat treatment at 200-660 °C,while only NiAl and Ni3Al exist at 660-1100 °C.Homogeneous WC＋Ni3Al powder mixture can be obtained in the temperature range of 1100-1200 °C.The WC-30%（Ni3Al-B） composites prepared from the mixed powders by conventional powder metallurgy technology show nearly full density and the shape of WC is round.WC-30%（Ni3Al-B） composites exhibit higher hardness of 9.7 GPa,inferior bending strength of 1800 MPa and similar fracture toughness of 18 MPa-m1/2 compared with commercial cemented carbides YGR45（WC-30%（Co-Ni-Cr））.

Processing and characterization of AZ91 magnesium alloys via a novel severe plastic deformation method:Hydrostatic cyclic extrusion compression(HCEC)

Capability of a novel severe plastic deformation(SPD)method of hydrostatic cyclic extrusion compression(HCEC)for processing of hcp metallic rods with high length to diameter ratios was investigated.The process was conducted in two consecutive cycles on the AZ91 magnesium alloy,and microstructural evolution,mechanical properties and corrosion behavior were investigated.The results showed that the HCEC process was successively capable of producing ultrafine-grained long magnesium rods.Its ability in improving strength and ductility simultaneously was also shown.The ultimate tensile strength and elongation to failure of the sample after the second cycle of the process were improved to be 2.46 and 3.8 times those of the as-cast specimen,respectively.Distribution of the microhardness after the second cycle was uniform and its average value was increased by 116%.The potentials derived from the polarization curves were high and the currents were much low for the processed samples.Also,the diameter of the capacitive arcs derived from the Nyquist curves was large in the HCEC processed samples.The finite element analysis indicated the independency of HCEC load from the length in comparison to the conventional CEC.HCEC is a unique SPD method,which can produce long ultrafine-grained rods with a combination of superior mechanical and corrosion properties.

3D analytical solution for a rotating transversely isotropic annular plate of functionally graded materials

The analytical solution for an annular plate rotating at a constant angular velocity is derived by means of direct displacement method from the elasticity equations for axisymmetric problems of functionally graded transversely isotropic media. The displacement components are assumed as a linear combination of certain explicit functions of the radial coordinate, with seven undetermined coefficients being functions of the axial coordinate z. Seven equations governing these z-dependent functions are derived and solved by a progressive integrating scheme. The present solution can be degenerated into the solution of a rotating isotropic functionally graded annular plate. The solution also can be degenerated into that for transversely isotropic or isotropic homogeneous materials. Finally, a special case is considered and the effect of the material gradient index on the elastic field is illustrated numerically.

Parvovirus B19 induced hepatic failure in an adult requiring liver transplantation

Parvovirus B19 induced acute hepatitis and hepatic failure have been previously reported, mainly in children. Very few cases of parvovirus induced hepatic failure have been reported in adults and fewer still have required liver transplantation. We report the case of a 55-year-old immunocompetent woman who developed fulminant hepatic failure after acute infection with Parvovirus B19 who subsequently underwent orthotopic liver transplantation. This is believed to be the first reported case in the literature in which an adult patient with fulminant hepatic failure associated with acute parvovirus B19 infection and without hematologic abnormalities has been identified prior to undergoing liver transplantation. This case suggests that Parvovirus B19 induced liver disease can affect adults, can occur in the absence of hematologic abnormalities and can be severe enough to require liver transplantation.

Thermodynamic properties and heat capacity of Ru metal in HCP,FCC,BCC and liquid state

Isometric heat capacity cv and isobar heat capacity cp of Ru metal in HCP,FCC,BCC and liquid state were calculated by using pure element systematic theory.The results are in good agreement with joint army-navy-air force(JANAF) experimental value and the calculation result by first-principle(FP) method.But the results have great differences in contrast to Scientific Group Thermodata Europe(SGTE) database.The cause is found that it cannot neglect the electron devotion to heat capacity to adjust cp in one-atom(OA) method.The disparity between OA method and SGTE database was discussed.The main cause is that OA method adopts the crosspoint with iso-Ec-line and iso-a-line in hybritriangle to determine the properties,but SGTE database is obtained by extrapolation from activity measurements and critical assessment of data from a large number of binary system.Thermodynamic properties of Ru metal in HCP,FCC,BCC and liquid state,such as entropy S,enthalpy H and Gibbs energy G were calculated.Therefore,the full description of thermodynamic properties from 0 K to random temperature is implemented.

Adsorption and desorption properties of D318 resin for Cr(Ⅵ)

The adsorption capability of D318 resin for Cr（Ⅵ） was investigated by chemistry analysis. Experimental results show that D318 resin has the best adsorption ability for Cr（Ⅵ） at pH=3.16 in HAc-NaAc medium. The statically saturated adsorption capacity of the resin is 265.4 mg/g. The thermodynamic adsorption parameters, enthalpy change AH and free energy change AG298 of the adsorption reaction are 4.81 and -5.16 kJ/mol, respectively. The apparent activation energy Ea is 22.4 kJ/mol. The adsorption behavior obeys the Freundlich isotherm. The molar coordination ratio of the functional group of resin to Cr（Ⅵ） is 3：2. Cr（Ⅵ） adsorbed on D318 resin can be eluted by 5%NaOH-5%NaCl quantitatively.

Effects of solution heat treatment on microstructure and mechanical properties of AZ61-0.7Si magnesium alloy

The effects of solution heat treatment on the microstructure and mechanical properties of AZ61-0.7Si magnesium alloy were investigated.The results indicate that the solution heat treatment can modify the Chinese script shaped Mg2Si phases in the AZ61-0.7Si magnesium alloy.After being solutionized at 420℃ for 16-48 h,the morphology of the Mg2Si phases in the AZ61-0.7Si alloy changes from the Chinese script shape to the short pole and block shapes.Accordingly,the tensile and creep properties of the AZ61-0.7Si alloy are improved.After being solutionized at 420℃ for 24 h and followed by aging treatment at 200℃ for 12 h,the heat-treated alloy exhibits relatively high tensile and creep properties than those of the as-cast alloy.

Effect of Si content on interfacial reaction and properties between solid steel and liquid aluminum

The effect of Si content on the microstructures and growth kinetics of intermetallic compounds(IMCs)formed during the initial interfacial reaction(<10 s)between solid steel and liquid aluminum was investigated by a thermophysical simulation method.The influence of Si addition on interfacial mechanical properties was revealed by a high-frequency induction brazing.The results showed that IMCs layers mainly consisted ofη-Fe_(2)Al_(5)andθ-Fe_(4)Al_(13).The addition of Si reduced the thickness of the IMCs layer.The growth of theηphase was governed by the diffusion process when adding 2 wt.%Si to the aluminum melt.When 5 wt.%or 8 wt.%Si was added to aluminum,the growth was governed by both the diffusion process and interfacial reaction,and ternary phaseτ1/τ9-(Al,Si)_(5)Fe_(3)was formed in theηphase.The apparent activation energies of theηphase decreased gradually with increasing Si content.The joint with pure aluminum metal had the highest tensile strength and impact energy.

Influences of gap size and cyclic-thermal-shock treatment on mechanical properties of TLP bonded IN-738LC superalloy

Influences of gap size and cyclic-thermal-shock treatment on the mechanical properties of transient liquid phase（TLP） bonded IN-738 LC superalloy were investigated. For this purpose, TLP bonding of IN-738 LC superalloy was carried out in a vacuum furnace using powdered AMS 4777 as the filler metal. The results showed that isothermal solidified zone（ISZ） consisted of Ni solid-solution and the distribution of alloying elements was homogeneous. High hardness of HV 409 and high shear strength of 506 MPa were observed in 40 μm gap sample. Alloying elements formed γ′ precipitates and the solid-solution in the ISZ. Hardness and shear strength of bonds were reduced with increasing the gap size（in range of 40-120 μm）. The fractured surfaces of complete isothermal solidified bonds showed dimpled rupture, but athermal solidified bonds showed cleavage fracture surface. 10, 20, 30 and 40 thermal-shock cycles were applied to 80 μm gap samples, respectively. The shear strength of the bond was measured to be 268 MPa after the 40 th thermal-shock cycle. The sample with gap size of 80 μm was failed due to crack nucleation on faying surface at 45 th thermal-shock cycle. The amount of the produced brittleness due to quenching the samples in water bath was attributed to the number of thermal-shock cycles.

Effect of extrusion ratios on hardness,microstructure,and crystal texture anisotropy in pure niobium tubes subjected to hydrostatic extrusion

Nb tubes were fabricated through hydrostatic extrusion at extrusion ratios of 3.1 and 6.1 at ambient temperature,and then their microstructure,texture,and Vickers hardness were investigated based on electron back-scattered diffraction(EBSD)data.The fraction of low-angle boundaries(LABs)largely decreased with a sharp decrease in mean grain sizes after hydrostatic extrusion and was not proportional to extrusion ratios,assuming that mixed-asymmetrical junctions forming LABs dissociate at high extrusion ratios from the external stress(>981 MPa)with thermal activation by the generated heat.The correlation between grain size and Vickers hardness followed the Hall−Petch relationship despite the texture gradient of theá111ñcyclic fiber textural microstructure at low extrusion ratios and theá100ñtrue fiber textural microstructure at high extrusion ratios.The increase in hydrostatic pressure on the Nb tubes contributed to texture evolution in terms of extrusion ratios due to the difference between{110}<111>and{112}<111>components based on EBSD data.

Effect of Fe content on microstructure and mechanical properties of Cu-Fe-based composite coatings by laser induction hybrid rapid cladding

To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser induction hybrid rapid claddingwas investigated. Microstructure characterization of the composite coatings was tested utilizing SEM, XRD and EDS. Microhardnessmeasurement was executed to evaluate the mechanical properties of the composite coatings. The results show that for low Fe content,the composite coating presents a feature that Fe-rich equiaxed dendrites are embedded in the Cu-rich matrix. With increasing Fecontent, the Fe-rich particles are dispersed in the Cu-rich matrix. With further increasing Fe content, large amounts of Cu-richparticles are homogeneously dispersed in the interdendrite of the Fe-rich matrix. Correspondingly, the average microhardness of thecomposite coatings increases gradually with the increase of Fe content and the microhardness of Cu14.5Fe83Si2C0.5 coating is muchtwice higher than that of the substrate.

Microstructure and mechanical properties of 8YSZ ceramics by liquid-phase sintering with CuO-TiO_2 addition

The 8% （mass fraction） yttrium-partially-stabilized zirconia （8YSZ） ceramic was fabricated via liquid phase sintering at 1 200-1 400℃ by adding different mass ratios of CuO-16.7%TiO2 （molar fraction） as sintering aid. Relative density, microstructure, Vickers hardness and bending strength as a function of sintering temperature and additive content were investigated. The experiment results show that liquid phase sintering at low temperature can be realized through adding CUO-16.7% TiO2 to 8YSZ. The Vickers hardness and bending strength of samples with sintering aid are generally much higher than those of samples without sintering aid for all sintering temperatures, and increase with the increase of sintering temperature. When the addition content of CUO-16.7% TiO2 is beyond 0.5%, the relative density, Vickers hardness and bending strength decrease with the increase of the mass ratio of sintering aid. Low additions of sintering aid are beneficial to aiding densification; high additions of sintering aid are detrimental to the sintered properties mainly due to greater amounts of pores generated by the volatilization of oxygen with the eutectic reaction between copper oxide and titanium dioxide. It is found that the fine grain size and high relative density are two main reasons of the high bending strength and Vickers hardness of the materials.

Partial transient-liquid-phase bonding of TiC cermet to stainless steel using impulse pressuring with Ti/Cu/Nb interlayer

Partial transient liquid phase （PTLP） bonding of TiC cermet to 06Cr19Ni10 stainless steel was carried out. Impulse pressuring was used to reduce the bonding time, and a Ti/Cu/Nb interlayer was employed to alleviate the detrimental effect of interfacial reaction products on the bonding strength. Successful bonding was achieved at 885℃ under a pulsed pressure of 2-10 MPa within durations in the range of 2-8 min, which was notably shortened in comparison with conventional PTLP bonding. Microstructure characterization revealed the o- phase with a limit solubility of Nb, a sequence of Ti-Cu intermetallic phases and solid solutions of Ni and Cu in α＋β Ti in the reaction zone. The maximum shear strength of 106.7 MPa was obtained when the joint was bonded for 5 rain, indicating that a robust metallurgical bonding was achieved. Upon shear loading, the joints fractured along the Ti-Cu intermetallics interface and spread to the interior of TiC cermet in a brittle cleavage manner.

Characteristics of semen parameters of Malawian men from couples seeking assisted reproduction

AIM: To profile semen parameters of Malawian men seeking fertility testing. METHODS: Semen analysis is a key element in the fertility evaluation of men and permits male reproductive potential to be evaluated. Semen samples were collected from consenting men after 3-5 d of sexual abstinence. The samples were collected from 130 males; 78 were male partners of infertile couples while 52 were healthy semen donors. Seminal volume, motility and morphology were assessed. The results were analyzed on Prism 5. All data are expressed as mean ± SD. Student's t-test was used for statistical analysis. Differences were regarded as statistically signifi cant if P < 0.05.RESULTS: Semen volume, sperm concentration, progressive motility and normal morphology were significantly higher in the control group when compared to the participant group. On the other hand, no statistically signifi cant difference was found between the control group total sperm motility when compared to the participant group. Oligozoospermia was found in 25 cases, teratozoospermia detected in 17 cases and abnormal seminal plasma in 16 cases. Asthenozoospermia and azoosper-mia were found in 12 and 8 participants, respectively. This study has shown that most of the infertile patients seeking fertility testing had oligozoospermia. Teratozoospermia was the second most common abnormality found in the patients seeking fertility testing. CONCLUSION: Our study is in agreement with previous studies which reported that these parameters have been shown to be good predictors for fertilization.

Rheological and drag reduction properties of hydroxypropyl xanthan gum solutions

Hydroxypropyl xanthan gum(HXG) was prepared from xanthan gum(XG) and propylene oxide under alkaline condition. Rheological and drag reduction properties of different concentrations of aqueous HXG and XG solution were studied. The micro-structure network of HXG and XG solutions was investigated by Cryo-FESEM. The results showed that HXG and XG solutions could exhibit shear thinning property. The apparent viscosity of6 g·L-1HXG solution was 1.25 times more than that of 6 g·L-1XG solution. The storage modulus G′ and the loss modulus G″ of HXG solutions were greater than those of XG solutions, and thixotropic and viscoelastic properties were more significant in HXG solutions. The HXG and XG solutions reduced the pressure drop of straight pipe, and the maximum drag reduction of 1 g·L-1HXG and XG in smooth tube reached 72.8% and 68.1%, respectively. Drag reduction rate was increased as the concentration increased. The HXG solution may become a new polymeric drag reducer.

Effects of Vibration Technology and Polyvinyl Acetate Emulsion on Microstructure and Properties of Expanded Polystyrene Lightweight Concrete

To prevent expanded polystyrene （EPS） beads from rising up to the surface in the molding process of EPS lightweight concrete, vibration with pressure was applied and the polyvinyl acetate （PVA） emulsion was adopted to improve its mechanical properties. The mechanical properties, thermal properties and durability of EPS lightweight concrete were tested. The microstruetures of EPS lightweight concrete were observed by scanning electron microscope （SEM）. Vibration with pressure reduces the number of small cracks. The 180 d compressive strength and flexural strength increase obviously as a large amount of PVA was added. The mixed amount of PVA has no obvious influence on the thermal performance when it is not more than 10% of the cement. Vibration with pressure and surface modification of EPS beads by PVA improve the combination of EPS beads with cement stone and the mechanical properties of EPS lightweight concrete.