Ring hoop tension test and tube bulging test were carried out at elevated temperatures up to 480 ℃to evaluate the formability of AZ31B extruded tube for internal high pressure forming （IHPF） process. The total elon...Ring hoop tension test and tube bulging test were carried out at elevated temperatures up to 480 ℃to evaluate the formability of AZ31B extruded tube for internal high pressure forming （IHPF） process. The total elongation along hoop direction and the maximum expansion ratio （MER） of the tube were obtained. The fracture surface after bursting was also analyzed. The results show that the total elongation along hoop direction and the MER value have a similar changing tendency as the testing temperature increases, which is quite different from the total elongation along axial direction. Both the total elongation along hoop direction and the MER value increase to a peak value at about 160 ℃. After that, they begin to decrease quickly until a certain rebounding temperature is reached. From the rebounding temperature, they begin to increase rapidly again. Burnt structure appears on the fracture surface when tested at temperatures higher than 420 ℃. Therefore, the forming temperature of the tested tube should be lower than 420 ℃, even though bigger formability can be achieved at higher temperature.展开更多
With the rapid rising of heat flux and reduction of heat dissipating space of microelectronic devises, flattened sintered heat pipe has become an ideal conducting element of use in the electronic cooling field. A manu...With the rapid rising of heat flux and reduction of heat dissipating space of microelectronic devises, flattened sintered heat pipe has become an ideal conducting element of use in the electronic cooling field. A manufacturing technology named phase change flattening process is presented to fabricate the flattened grooved-sintered wick heat pipe （GSHP for short）. Deformation geometry of flattened GSHP and the elasto-plastic deformation of flattening process are analyzed theoretically and verified by experiments. The results show that the vapor pressure inside sintered heat pipe during flattening process is determined by the saturated vapor pressure equation; the width and vapor area of flattened heat pipe change greatly as the flattening proceeds; the maximum equivalent strain distributes at the interface between wick and vapor in the fiat section; the buckling phenomenon can be well eliminated when the flattening temperature reaches 480 K; phase change flattening punch load increases with flattening temperature and displacement.展开更多
In order to study the laws of the extrusion pressure changing with the extrusion parameters in the process of hydrostatic extrusion for the tungsten alloys, the large deformation elasto plastic theory and the sof...In order to study the laws of the extrusion pressure changing with the extrusion parameters in the process of hydrostatic extrusion for the tungsten alloys, the large deformation elasto plastic theory and the software of ANSYS 5 5 are used to carry out the numerical simulation research. The laws of the extrusion pressure changing with the extrusion parameters, such as the die angle, extrusion ratio, and friction coefficient, are obtained. The simulation results are in good agreement with the experimental ones, and the simulated results are believable.展开更多
The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch...The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch, equations that are used to decide the lubricating oil flow and the number of oil films (i.e. the number of rotating and stationary plates) are deduced theoretically. Also key parameters are provided for the design of the hydraulic system. All these together provide the theoretical basis for the soft start design of the belt conveyor and references for the application of the oil film clutch in similar fields.展开更多
A Fe/Al clad tube was prepared by explosive welding.Then the bonding characteristic of the interface was investigated by compression,flattening and compression-shear test.The test results exhibit that the clad tubes p...A Fe/Al clad tube was prepared by explosive welding.Then the bonding characteristic of the interface was investigated by compression,flattening and compression-shear test.The test results exhibit that the clad tubes possessing good bonding interface have higher shear strength than that of pure aluminum and can bear both axial and radial deformation.The original interface between aluminum layer and ferrite layer was observed by scanning electron microscopy（SEM）.The results show that the clad tubes with good bonding properties possess the interface in wave and straight shape.The Fe/Al clad tube was used to manufacture the T-shape by hydro-bulging.It is found that the good-bonding interface of the Fe/Al clad tube plays a dominant role in the formation of the T-shape.展开更多
Using magnetorheological (MR) fluids in hydraulic engine mount for damping vehicle noise and vibration is opposed firstly, the structure of passive type and its mechanical model are described. The analysis of the expe...Using magnetorheological (MR) fluids in hydraulic engine mount for damping vehicle noise and vibration is opposed firstly, the structure of passive type and its mechanical model are described. The analysis of the experimental data show that the dynamic characteristics of MR mount such as dynamic stiffness and loss angles vary distinctly as the excitation frequency, and MR fluids as one type of attracting controllable fluids are fit for hydraulic engine mounts. The author advises to work out potentialities of MR fluids, the semi control or active control MR fluids filled hydraulic engine mount must be developed.展开更多
Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio o...Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.展开更多
Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio o...Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.展开更多
A nonlinear dynamics model and a mathematical expression were set up to investigatethe mechanism and conditions of vibration creep acceleration.The model showsthat hydraulic spring and nonlinear friction are major fac...A nonlinear dynamics model and a mathematical expression were set up to investigatethe mechanism and conditions of vibration creep acceleration.The model showsthat hydraulic spring and nonlinear friction are major factors that can affect low-speed instability.The mathematic model was established to obtain the change rule of speed andinstantaneous acceleration of the hydraulic motor.Then, Matlab was used to simulate theeffect of nonlinear friction force and hydraulic motor parameters such as coefficient of leakand compression ratio, etc., under low speed.Finally, some measures were proposed toimprove the low-speed stability of the hydraulic motor.展开更多
The non-random two liquids （NRTL） equation together with the Pitzer/Curl Virial equation of state are used to investigate the simultaneous representation of excess enthalpies （h^E） and vapour-liquid equilibria （...The non-random two liquids （NRTL） equation together with the Pitzer/Curl Virial equation of state are used to investigate the simultaneous representation of excess enthalpies （h^E） and vapour-liquid equilibria （VLE） and the VLE prediction from h^E data. The calculation strategy for properly determining NRTL parameters and the effect of their temperature dependence on the simultaneous correlation of h^E and VLE data and the VLE extrapolation are analysed in detail.展开更多
基金Project(50805033)supported by the National Natural Science Foundation of ChinaProject(E200804)supported by the Natural Science Foundation of Heilongjiang Province of China
文摘Ring hoop tension test and tube bulging test were carried out at elevated temperatures up to 480 ℃to evaluate the formability of AZ31B extruded tube for internal high pressure forming （IHPF） process. The total elongation along hoop direction and the maximum expansion ratio （MER） of the tube were obtained. The fracture surface after bursting was also analyzed. The results show that the total elongation along hoop direction and the MER value have a similar changing tendency as the testing temperature increases, which is quite different from the total elongation along axial direction. Both the total elongation along hoop direction and the MER value increase to a peak value at about 160 ℃. After that, they begin to decrease quickly until a certain rebounding temperature is reached. From the rebounding temperature, they begin to increase rapidly again. Burnt structure appears on the fracture surface when tested at temperatures higher than 420 ℃. Therefore, the forming temperature of the tested tube should be lower than 420 ℃, even though bigger formability can be achieved at higher temperature.
基金Project(50905119)supported by the National Natural Science Foundation of ChinaProject(2012M510205)supported by China Postdoctoral Science Foundation+1 种基金Project(PEMT1206)supported by the Open Foundation of Guangdong Province Key Laboratory of Precision Equipment and Manufacturing Technology,ChinaProject(S2012040007715)supported by Natural Science Foundation of Guangdong Province,China
文摘With the rapid rising of heat flux and reduction of heat dissipating space of microelectronic devises, flattened sintered heat pipe has become an ideal conducting element of use in the electronic cooling field. A manufacturing technology named phase change flattening process is presented to fabricate the flattened grooved-sintered wick heat pipe （GSHP for short）. Deformation geometry of flattened GSHP and the elasto-plastic deformation of flattening process are analyzed theoretically and verified by experiments. The results show that the vapor pressure inside sintered heat pipe during flattening process is determined by the saturated vapor pressure equation; the width and vapor area of flattened heat pipe change greatly as the flattening proceeds; the maximum equivalent strain distributes at the interface between wick and vapor in the fiat section; the buckling phenomenon can be well eliminated when the flattening temperature reaches 480 K; phase change flattening punch load increases with flattening temperature and displacement.
文摘In order to study the laws of the extrusion pressure changing with the extrusion parameters in the process of hydrostatic extrusion for the tungsten alloys, the large deformation elasto plastic theory and the software of ANSYS 5 5 are used to carry out the numerical simulation research. The laws of the extrusion pressure changing with the extrusion parameters, such as the die angle, extrusion ratio, and friction coefficient, are obtained. The simulation results are in good agreement with the experimental ones, and the simulated results are believable.
文摘The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch, equations that are used to decide the lubricating oil flow and the number of oil films (i.e. the number of rotating and stationary plates) are deduced theoretically. Also key parameters are provided for the design of the hydraulic system. All these together provide the theoretical basis for the soft start design of the belt conveyor and references for the application of the oil film clutch in similar fields.
基金Project(BA2006067)supported by Achievement Transitional Foundation of Jiangsu Province,China
文摘A Fe/Al clad tube was prepared by explosive welding.Then the bonding characteristic of the interface was investigated by compression,flattening and compression-shear test.The test results exhibit that the clad tubes possessing good bonding interface have higher shear strength than that of pure aluminum and can bear both axial and radial deformation.The original interface between aluminum layer and ferrite layer was observed by scanning electron microscopy（SEM）.The results show that the clad tubes with good bonding properties possess the interface in wave and straight shape.The Fe/Al clad tube was used to manufacture the T-shape by hydro-bulging.It is found that the good-bonding interface of the Fe/Al clad tube plays a dominant role in the formation of the T-shape.
文摘Using magnetorheological (MR) fluids in hydraulic engine mount for damping vehicle noise and vibration is opposed firstly, the structure of passive type and its mechanical model are described. The analysis of the experimental data show that the dynamic characteristics of MR mount such as dynamic stiffness and loss angles vary distinctly as the excitation frequency, and MR fluids as one type of attracting controllable fluids are fit for hydraulic engine mounts. The author advises to work out potentialities of MR fluids, the semi control or active control MR fluids filled hydraulic engine mount must be developed.
文摘Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.
文摘Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.
基金Supported by the Natural Science Foundation of Fujian Province of China(2009J01259)Scientific Research Foundation of Department of Education(JB08182)
文摘A nonlinear dynamics model and a mathematical expression were set up to investigatethe mechanism and conditions of vibration creep acceleration.The model showsthat hydraulic spring and nonlinear friction are major factors that can affect low-speed instability.The mathematic model was established to obtain the change rule of speed andinstantaneous acceleration of the hydraulic motor.Then, Matlab was used to simulate theeffect of nonlinear friction force and hydraulic motor parameters such as coefficient of leakand compression ratio, etc., under low speed.Finally, some measures were proposed toimprove the low-speed stability of the hydraulic motor.
基金Supported by Deutsche Forschungsgemeinschaft(DFG) (LE 886/4-1)
文摘The non-random two liquids （NRTL） equation together with the Pitzer/Curl Virial equation of state are used to investigate the simultaneous representation of excess enthalpies （h^E） and vapour-liquid equilibria （VLE） and the VLE prediction from h^E data. The calculation strategy for properly determining NRTL parameters and the effect of their temperature dependence on the simultaneous correlation of h^E and VLE data and the VLE extrapolation are analysed in detail.
